Cisco SD208T-NA Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco SD208T-NA manuals!
Problems with Cisco SD208T-NA?
Ask a Question
Free Cisco SD208T-NA manuals!
Problems with Cisco SD208T-NA?
Ask a Question
Popular Cisco SD208T-NA Manual Pages
Administration Guide - Page 31
... the firmware image.
• Language File-The dictionary that controls the operations and functionality of a specific operating state. You can be displayed in the selected language.
• Flash Log-SYSLOG messages stored in the Downloading or Backing-up a Configuration or Log
• Viewing Configuration Files Properties
Cisco Small Business 200 Series Smart Switch Administration Guide...
Administration Guide - Page 33
...network. Cisco Small Business 200 Series Smart Switch Administration Guide
34...Upgrade/Backup Firmware/Language
4
Select one link local address is used).
Enter the following actions:
• Upgrade Save Action-Specifies that the file type on the switch...supported. The options are described in the Files and File Types section).
• TFTP Server Definition-Select whether to be replaced...
Administration Guide - Page 53
... SNTP Server Mode-The switch sends Unicast queries to a list of the switch through a DHCP server, where:
-
SNTP Modes
The switch can be set on the closest stratum (distance from the reference clock). Cisco Small Business 200 Series Smart Switch Administration Guide
54 Dynamic DST, when enabled and available, always takes precedence over the manual configuration of the following ways...
Administration Guide - Page 54
... set manually and the switch is rebooted, the manual time settings must also configure a connection to an SNTP server in order for example: Time Based ACL, Port, 802.1 port ...Cisco Small Business 200 Series Smart Switch Administration Guide
55 To use this , the system time is no alternate source of the above in the SNTP Interface Settings page. The local time is manual, you must be set...
Administration Guide - Page 55
... following :
- Recurring-DST occurs on the switch.
NOTE The DHCP Client supports Option 100 providing dynamic time zone setting.
Time Zone Settings-The local time is 60.
• Daylight...page. To-Day and time that DST starts.
- Cisco Small Business 200 Series Smart Switch Administration Guide
56 European-DST is set manually, typically for New York is enabled, you must also...
Administration Guide - Page 74
....3 MAC-PHY-Duplex and bit rate capability and the current duplex and bit rate settings of the sending device. The following fields relate to the Management Address:
• Advertisement Mode-Select one of the MAC/ PHY implementation. Cisco Small Business 200 Series Smart Switch Administration Guide
75 This includes the system's name and versions of the...
Administration Guide - Page 75
...), Emergency Call Service (E-911) by using IP Phone location information.
• Troubleshooting information. Some of...Manual Advertise-Select this option and the management IP address to the Running Configuration file. QoS policy misconfigurations
Cisco Small Business 200 Series Smart Switch Administration Guide
76 STEP 3 Enter the relevant information, and click Apply. The port settings...
Administration Guide - Page 104
... is manually created, the LACP option cannot be added or removed, until the LAG is edited and a member is removed (which candidate ports are supported:
• Static-A LAG is static if the LACP is disabled on it .
The group of ports assigned to dynamic LAG are always active members.
Cisco Small Business 200 Series Smart Switch Administration Guide
105...
Administration Guide - Page 159
... ID after reboot.
The 200 Series switch supports up to a port. All packets classified to the Discard...replace the default VLAN ID after you reboot the switch. STEP 4 Click Save (in the upper-right corner of the window) and save the Running Configuration to one port, either manually...Cisco Small Business 200 Series Smart Switch Administration Guide
160
The Add/Edit VLAN page is displayed.
Administration Guide - Page 162
... ), must be to the VLAN. Cisco Small Business 200 Series Smart Switch Administration Guide
163
When a port is displayed with its current registration to the VLAN. This is the default for each port or LAG is currently not a member of the VLAN are sent untagged to display and configure the ports within a specific VLAN.
Otherwise, traffic might leak from...
Administration Guide - Page 166
... Ethernet MAC address. VSDP is enabled.
Cisco Small Business 200 Series Smart Switch Administration Guide
167 A different voice VLAN can also be added dynamically if the switch is defaulted to VLAN 1. By default, the voice VLAN is manually configured as a candidate to join the voice VLAN, the switch dynamically adds the port to the voice VLAN if it receives...
Administration Guide - Page 227
... characters from at least three character classes (uppercase letters, lowercase letters, numbers, and special characters available on a standard keyboard).
• Are different from the current password.
• Contain no password).
NOTE Password aging also applies to change . Cisco Small Business 200 Series Smart Switch Administration Guide
228
Administration Guide - Page 236
... in this window. Cisco Small Business 200 Series Smart Switch Administration Guide
237 Configuring Security
Configuring TCP/UDP Services
STEP 5 Click Apply, and the rule is added to the access profile.
17
Configuring TCP/UDP Services
The TCP/UDP Services page enables TCP or UDP-based services on the displayed services.
• HTTP Service-Indicates whether the HTTP service is enabled or...
Administration Guide - Page 248
... that SCT is enabled by default on it. The Security Suite Settings displays.
Denial of Service Prevention > Security Suite Settings page (Details button).
CPU Protection Mechanism: Enabled indicates that the switch receives and processes management and protocol traffic, no interactions with other features. Cisco Small Business 200 Series Smart Switch Administration Guide
249
Administration Guide - Page 274
... CoS/ 802.1p trusted mode or DSCP trusted mode. STEP 4 Select the Port or LAG interface. QoS State displays whether QoS is enabled on the system wide configured trusted mode, which is based on the interface. Configuring Quality of Service > General > Interface Settings. QoS State of ports or LAGs.
Cisco Small Business 200 Series Smart Switch Administration Guide
275
Cisco SD208T-NA Reviews
We have not received any reviews for Cisco yet.