Cisco SFE2000 - Small Business Managed Switch Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco SFE2000 manuals!
Problems with Cisco SFE2000?
Ask a Question
Free Cisco SFE2000 manuals!
Problems with Cisco SFE2000?
Ask a Question
Cisco SFE2000 Videos
SYS2U.COM - ???????? Cisco SFE2000 - 24-Port 10/100 Stackable L3 Switch
Duration: 3:22
Total Views: 644
Duration: 3:22
Total Views: 644
Popular Cisco SFE2000 Manual Pages
Administration Guide - Page 3
... Port
3
3 3 3 4 4 5 5 5 6 6 7 7 7
Chapter 3: Connecting the Switch 8
Overview
8
Before You Install the Switch...
8
Placement Options
9
Desktop Placement
9
Rack-Mount Placement
9
Wall-Mount Placement
10
Connecting the Cables
10
Stacking Multiple Switches
12
Connecting Cabling for Stacking
13
Managing Stacks
14
Building Automatically-Configured Stacks
14
Building Manually...
Administration Guide - Page 4
... Unit Startup Process
17
Configuring Units and Ports
20
Setting the Unit's Operational Mode
21
Configuring the Stack Master and Unit ID
21
Resetting the Unit to Factory Default Mode
23
Understanding LED Indicators
23
Stack Troubleshooting and Maintenance
24
Replacing a Failed Member Stack Unit in an Operational Stack
24
Replacing a Failed Stack Master Unit in an...
Administration Guide - Page 7
... entire PoE system can synchronize its clock with the Linksys One Portal - These instructions should be centrally powered by uninterruptible power supplies if necessary.
With Simple Network Time Protocol (SNTP), the Ethernet switch can be all facets of network devices, and significantly decreasing installation costs.
Chapter 1: Introduction
1
What's in this User Guide? It...
Administration Guide - Page 9
... ID 5 number of the Ethernet switch power, fan, RPS connectivity, and stack master.
These ports can be used to supply power to various Linksys products over -Ethernet (PoE) which support network speeds of the Linksys system. Chapter
Linksys One Ready Communications Solution
2 Getting to Know the Switch
Overview
The SFE2000 and SFE2000P models are shared with ports mini-GBIC 4 1 and...
Administration Guide - Page 10
... red FAN LED indicates that the Ethernet switch is powered by a remote power supply (RPS), this Ethernet switch is actively sending or receiving data over that port.
• On the SFE2000, a green Link LED indicates that the port is linked to a 10/100Mbps device.
• On the SFE2000P, a green Link LED indicates that PoE is connected and operating properly.
A green...
Administration Guide - Page 12
... Ethernet switch.
In stacking mode, two ports are shared with an RJ-45 connector.
The MGBSX1 and the MGBLH1 require fiber cabling with LC connectors, while the MGBT1 requires a Category 5e Ethernet cable with GBIC1 and GBIC2 ports, respectively.
For more details, refer to
"Power Port," on page 7.
1
2
3
DC INPUT FOR REMOTE POWER SUPPLY SPECIFIED IN MANUAL...
Administration Guide - Page 18
... device operates as regular network ports.
• Settings are Master-Enabled units. A stack unit can be running on FE units) are reserved for stacking links, and cannot be used for regular network connections.
• The Stack Master switch maintains the configuration.
• Stack cannot combine Linksys SFE2000 and SGE2000 family Ethernet switches. of-one Master Backup...
Administration Guide - Page 26
... the command-line interface (CLI) or GUI to configure the stack units. Linksys One Ready Communications Solution
3
20
Chapter 3: Connecting the Switch
Configuring Units and Ports If there are more units...NOTE: If a unit is the Stack Master, and one exists. Chapter
manually-set Unit ID number are shut down , its ports according to the configuration file present on the Stack Master. If a ...
Administration Guide - Page 31
... not joined to the default settings.
• If the units have uplink ports, then the first uplink port of the unit it replaced, then when possible, it was in memory, even though the first 24 are configured according to the configuration of the first 24 ports of the
Chapter 3: Connecting the Switch
25
Stack Troubleshooting and Maintenance The Stack...
Administration Guide - Page 42
... Use this screen to check firmware versions and general system information for the Ethernet switch. Help System Configuration Menu On the System Configuration Menu screen, you have these choices: 1. User & Password Settings 4. Restore System Default Settings 8. System Mode (Layer 2 / Layer 3) Selection 5.
System Configuration Menu 2. Port Configuration 4. IP Configuration 6. File...
Administration Guide - Page 43
... hardware firmware versions
of the Ethernet switch. Chapter
Linksys One Ready Communications Solution
4
Versions
Use the Versions screen to save your changes are complete, press the Esc key to return to make changes.
Chapter 4: Console Configuration
37
Configuring the Switch through the Console or Telnet Interface To change general system information:
a. b. Management Settings...
Administration Guide - Page 52
...change the settings. When you to make changes. File Management
The File Management screen allows you copy an image to the switch via the console port, the active image is replaced. Active ... on the Ethernet switch: Image 1 and Image 2.
Specify the source and destination of the file, the file name, and the IP address of the file server where the upgrade file is replaced.
Linksys One...
Administration Guide - Page 56
... for a particular screen, click on the Help button located on the default VLAN 100.
The IP address of the Ethernet switch is determined by default to manage it is part of your web browser. Refer to configure the Ethernet switch. NOTE: The Ethernet switch is accessible through your Ethernet switch is with the Linksys One Portal -
For example: type http://192...
Administration Guide - Page 63
... of your product or experience a problem with the product you with your product to Linksys at www.linksys.com. This limited warranty gives you specific legal rights, and you .
Appendix C: Limited Warranty
57
OBTAINING WARRANTY SERVICE
OBTAINING WARRANTY SERVICE
If you have other items with it, please go to www.linksys.com/support where you . Do not include any...
Administration Guide - Page 66
...
Models Standards
Ports
Cabling Type PoE
Switching Capacity LEDs Stack Operation
Buttons
• SFE2000 - 24-port 10/100 Ethernet switch • SFE2000P - 24-port 10/100 Ethernet switch with PoE
802.3 10BASE-T Ethernet, 802.3u 100BASE-TX Fast Ethernet, 802.3ab 1000BASE-T Gigabit Ethernet, 802.3z Gigabit Ethernet, 802.3x Flow Control, 802.3ad LACP,802.3af POE, 802.1d STP, 802.1Q/p VLAN...
Cisco SFE2000 Reviews
We have not received any reviews for Cisco yet.