Software Guide
Page 16
.../100BASE-T Fast Ethernet ports are numbered Fast Ethernet 0/0 and Fast Ethernet 0/1, from right to left. Figure 1-2 Back-Panel Functions and Options (Cisco VG224 shown) 95914 1 2 VG224-24FXS 3 4 56 8 9 7 10 1 Chassis ground connection 6 AUX port 2 RJ-21 connector 7 Console port 3 Compact flash port 8 DC power input1 4 Fast Ethernet port 1 9 On/off switch 5 Fast...
.../100BASE-T Fast Ethernet ports are numbered Fast Ethernet 0/0 and Fast Ethernet 0/1, from right to left. Figure 1-2 Back-Panel Functions and Options (Cisco VG224 shown) 95914 1 2 VG224-24FXS 3 4 56 8 9 7 10 1 Chassis ground connection 6 AUX port 2 RJ-21 connector 7 Console port 3 Compact flash port 8 DC power input1 4 Fast Ethernet port 1 9 On/off switch 5 Fast...
Software Guide
Page 32
... the prompt changes to Router(config-if)#. Step 6 Router(config-if)# ipx network B005 Configures routing protocols on the Cisco VG224. In this example, IPX is not connected to the Cisco VG224. • Power on the interface. Password: password Router# You have previously enabled these protocols as required for...you plan to route, you begin, disconnect all WAN cables from the Cisco VG224 to keep it from trying to run AutoInstall whenever you power it on if there is a WAN connection on both ends and the Cisco VG224 does not have a valid configuration file stored in NVRAM (for instance...
... the prompt changes to Router(config-if)#. Step 6 Router(config-if)# ipx network B005 Configures routing protocols on the Cisco VG224. In this example, IPX is not connected to the Cisco VG224. • Power on the interface. Password: password Router# You have previously enabled these protocols as required for...you plan to route, you begin, disconnect all WAN cables from the Cisco VG224 to keep it from trying to run AutoInstall whenever you power it on if there is a WAN connection on both ends and the Cisco VG224 does not have a valid configuration file stored in NVRAM (for instance...
Software Guide
Page 36
... network module or WAN interface card. Note If the current configuration is valid, you need instructions for connecting a console, refer to the installation chapter of the Cisco VG224. In this procedure: Step 1 Step 2 Connect a console to the Cisco VG224. For instructions, see the user EXEC prompt (Router>). Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step...
... network module or WAN interface card. Note If the current configuration is valid, you need instructions for connecting a console, refer to the installation chapter of the Cisco VG224. In this procedure: Step 1 Step 2 Connect a console to the Cisco VG224. For instructions, see the user EXEC prompt (Router>). Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step...
Software Guide
Page 55
.../univercd/cc/td/doc/product/access/acs_mod/cis2600/hw_inst/cabling/ 2610ja.htm OL-5005-01 Cisco VG224 Voice Gateway Software Configuration Guide C-1 During normal operation, the ROM monitor helps to initialize the processor hardware and boot the operating system software. C A P P E N D I X ... that runs when you must have access to the console port. You can also use the ROM monitor, you power on connecting the console cable, refer to Quick Start Guide Cisco 2610 Router Cabling and Setup at the following sections: • Entering the ROM Monitor Mode, page C-1 • ROM Monitor Commands,...
.../univercd/cc/td/doc/product/access/acs_mod/cis2600/hw_inst/cabling/ 2610ja.htm OL-5005-01 Cisco VG224 Voice Gateway Software Configuration Guide C-1 During normal operation, the ROM monitor helps to initialize the processor hardware and boot the operating system software. C A P P E N D I X ... that runs when you must have access to the console port. You can also use the ROM monitor, you power on connecting the console cable, refer to Quick Start Guide Cisco 2610 Router Cabling and Setup at the following sections: • Entering the ROM Monitor Mode, page C-1 • ROM Monitor Commands,...
Software Guide
Page 62
...rom-monitor preference command in flash memory, you can recover the Cisco IOS image using one of main memory Main memory is configured to a Fast Ethernet port. xmodem [filename]-Establishes an xmodem connection between a console and the router console port for first time ...System Bootstrap, Version 12.3(4)T, RELEASE SOFTWARE (fc1) TAC Support: http://www.cisco.com/tac Copyright (c) 2002 by cisco Systems, Inc. Entering the ROM Monitor Mode Appendix...
...rom-monitor preference command in flash memory, you can recover the Cisco IOS image using one of main memory Main memory is configured to a Fast Ethernet port. xmodem [filename]-Establishes an xmodem connection between a console and the router console port for first time ...System Bootstrap, Version 12.3(4)T, RELEASE SOFTWARE (fc1) TAC Support: http://www.cisco.com/tac Copyright (c) 2002 by cisco Systems, Inc. Entering the ROM Monitor Mode Appendix...