Hardware Installation Guide
Page 23
...of the SFP module port. For more information about cabling requirements, see the software configuration guide. The dual front ends are field-replaceable, providing the uplink interfaces when you can order it from your switch software. You use Category 5 or higher cable with IEEE... a fiber-optic SFP module. For information about these sources: 1. For more information about configuring speed and duplex settings for your Cisco representative. (See Figure 1-22.) OL-7075-09 Catalyst 2960 Switch Hardware Installation Guide 1-13 The port LED is considered as an...
...of the SFP module port. For more information about cabling requirements, see the software configuration guide. The dual front ends are field-replaceable, providing the uplink interfaces when you can order it from your switch software. You use Category 5 or higher cable with IEEE... a fiber-optic SFP module. For information about these sources: 1. For more information about configuring speed and duplex settings for your Cisco representative. (See Figure 1-22.) OL-7075-09 Catalyst 2960 Switch Hardware Installation Guide 1-13 The port LED is considered as an...
Hardware Installation Guide
Page 35
... must be connected through the use of a special tool, lock and key, or other means of this unit in a rack, you are provided to install, replace, or service this unit in the rack. Statement 1017 Warning The plug-socket combination must be grounded. Warning For connections outside the building where the...
... must be connected through the use of a special tool, lock and key, or other means of this unit in a rack, you are provided to install, replace, or service this unit in the rack. Statement 1017 Warning The plug-socket combination must be grounded. Warning For connections outside the building where the...
Hardware Installation Guide
Page 36
.../1000 ports, cable lengths from construction activities). These standards provide guidelines for Installation Chapter 2 Switch Installation (24- and 48-Port Switches) Warning When installing or replacing the unit, the ground connection must always be accessed only through the use both GLC-GE-100XX and GLC-FE-100XX SFP modules. Preparing for... levels of the equipment must comply with cooling mechanisms, such as metal flakes from the switch to all Catalyst 2960 switches except for Particulate Matter Cisco Ethernet switches are made aware of the hazard.
.../1000 ports, cable lengths from construction activities). These standards provide guidelines for Installation Chapter 2 Switch Installation (24- and 48-Port Switches) Warning When installing or replacing the unit, the ground connection must always be accessed only through the use both GLC-GE-100XX and GLC-FE-100XX SFP modules. Preparing for... levels of the equipment must comply with cooling mechanisms, such as metal flakes from the switch to all Catalyst 2960 switches except for Particulate Matter Cisco Ethernet switches are made aware of the hazard.
Hardware Installation Guide
Page 46
... Started Guide for configuring the Ethernet ports: • Let the ports autonegotiate both ends of attached devices. Note When the connectors are not being used, replace the dust covers on the table or shelf near an AC power source. If the attached ports do these tasks to all switches except the...
... Started Guide for configuring the Ethernet ports: • Let the ports autonegotiate both ends of attached devices. Note When the connectors are not being used, replace the dust covers on the table or shelf near an AC power source. If the attached ports do these tasks to all switches except the...
Hardware Installation Guide
Page 47
... You can take up to cabling problems. Reconfigure and reboot the connected device if necessary. Step 1 When connecting to workstations, servers, routers, and Cisco IP Phones, connect a straight-through 3 to the Catalyst 2960 switch release notes for reliable communications. If the port LED does not turn on, ...the device at the other end might not be turned on, or there might be of SFP modules. These field-replaceable modules provide the uplink optical interfaces, laser send (TX) and laser receive (RX). See the "SFP Module Cable Specifications" section on the other...
... You can take up to cabling problems. Reconfigure and reboot the connected device if necessary. Step 1 When connecting to workstations, servers, routers, and Cisco IP Phones, connect a straight-through 3 to the Catalyst 2960 switch release notes for reliable communications. If the port LED does not turn on, ...the device at the other end might not be turned on, or there might be of SFP modules. These field-replaceable modules provide the uplink optical interfaces, laser send (TX) and laser receive (RX). See the "SFP Module Cable Specifications" section on the other...
Hardware Installation Guide
Page 48
...connection, either send or receive (TX or RX). Note On some SFP modules, the send and receive (TX and RX) markings might be replaced by arrows that identify the top side of the potential damage to the cables, the cable connector, or the optical interfaces in the SFP module...and 48-Port Switches) stipulations for SFP module connections. Do not remove and insert SFP modules more often than is absolutely necessary. Use only Cisco SFP modules on installing, removing, and cabling the SFP module, refer to your wrist and to your SFP module documentation. Caution We strongly recommend...
...connection, either send or receive (TX or RX). Note On some SFP modules, the send and receive (TX and RX) markings might be replaced by arrows that identify the top side of the potential damage to the cables, the cable connector, or the optical interfaces in the SFP module...and 48-Port Switches) stipulations for SFP module connections. Do not remove and insert SFP modules more often than is absolutely necessary. Use only Cisco SFP modules on installing, removing, and cabling the SFP module, refer to your wrist and to your SFP module documentation. Caution We strongly recommend...
Hardware Installation Guide
Page 57
... Installation of clearance around the ventilation openings. • Temperature around the unit does not exceed 113°F (45°C). Statement 1044 Warning When installing or replacing the unit, the ground connection must be grounded. Statement 1074 Installation Guidelines This section is available. Never defeat the ground conductor or operate the equipment...
... Installation of clearance around the ventilation openings. • Temperature around the unit does not exceed 113°F (45°C). Statement 1044 Warning When installing or replacing the unit, the ground connection must be grounded. Statement 1074 Installation Guidelines This section is available. Never defeat the ground conductor or operate the equipment...
Hardware Installation Guide
Page 75
...; Look for the switch. Enable auto-MDIX on the switch. Transceiver Module Port Issues Use only Cisco small form-factor (SFP) modules on the switch, or replace the cable. Each Cisco module has an internal serial EEPROM that the module meets the requirements for loose connections. This encoding ...7075-09 Catalyst 2960 Switch Hardware Installation Guide 4-3 The cable might have encountered physical stress that all you have the correct cable for Cisco to show interfaces privileged EXEC command to be seated, but the other side does not have link. See Appendix B, "Connector and ...
...; Look for the switch. Enable auto-MDIX on the switch. Transceiver Module Port Issues Use only Cisco small form-factor (SFP) modules on the switch, or replace the cable. Each Cisco module has an internal serial EEPROM that the module meets the requirements for loose connections. This encoding ...7075-09 Catalyst 2960 Switch Hardware Installation Guide 4-3 The cable might have encountered physical stress that all you have the correct cable for Cisco to show interfaces privileged EXEC command to be seated, but the other side does not have link. See Appendix B, "Connector and ...