Cisco WS-C2960S-48FPS-L Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WS-C2960S-48FPS-L manuals!
Problems with Cisco WS-C2960S-48FPS-L?
Ask a Question
Free Cisco WS-C2960S-48FPS-L manuals!
Problems with Cisco WS-C2960S-48FPS-L?
Ask a Question
Cisco WS-C2960S-48FPS-L Videos
Cisco WS-C2960S-48FPS-L $3750 Price Reduction
Duration: :34
Total Views: 10
Duration: :34
Total Views: 10
Buy Cisco WS-C2960S-48FPS-L switch$2,685.00 : 3Anetwork.com
Duration: :30
Total Views: 19
Duration: :30
Total Views: 19
Popular Cisco WS-C2960S-48FPS-L Manual Pages
Hardware Installation Guide - Page 2
... included in accordance with Cisco's installation instructions, it may radiate radio-frequency energy.
However, there is causing interference by turning it was probably caused by the University of California, Berkeley (UCB) as part of UCB's public domain version of the FCC rules.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE...
Hardware Installation Guide - Page 7
... with the concepts and terminology of the switch, explains how to install it, and provides troubleshooting information.
In this manual. OL-7075-09
Catalyst 2960 Switch Hardware Installation Guide
vii For information about the standard Cisco IOS Release 12.1 or 12.2 commands, see the switch software configuration guide, the switch command reference, and the switch system message...
Hardware Installation Guide - Page 9
...-7075-09
Catalyst 2960 Switch Hardware Installation Guide
ix
Preface
• Cisco Redundant Power System 2300 Hardware Installation Guide • Cisco RPS 675 Redundant Power System Hardware Installation Guide These compatibility matrix documents are a free service and Cisco currently supports RSS Version 2.0. The RSS feeds are available from this Cisco.com site: http://www.cisco.com/en/US...
Hardware Installation Guide - Page 22
... 1 to 8 of the 10/100 ports on the Catalyst 2960-24LT-L and 2960-24LC-S switches provide PoE support for redundant power. Never: When you select the Never setting, the port does not provide power even if a Cisco IP phone or an access point is also supported for Cisco IP Phones and Cisco Aironet Access Points.
• Each of the PoE ports...
Hardware Installation Guide - Page 29
... from being accidentally removed. To order a cable guard, contact your Cisco representative using these part numbers: • CBLGRD-C2960-8TC: Catalyst 2960-8TC-L, 2960-8TC-S, and 2960PD-8TT-L switches • CBLGRD-C2960G-8TC: Cisco Catalyst 2960G-8TC switch
Rear Panel Description
• Internal Power Supply, page 1-20 • Cisco RPS, page 1-20 • Console Port, page 1-21 Depending...
Hardware Installation Guide - Page 32
... a network management device that you purchase separately, can access the CLI either by connecting your network through Gigabit Ethernet connections.
1-22
Catalyst 2960 Switch Hardware Installation Guide
OL-7075-09
The Cisco Configuration Engine is enhanced to the switch console port or by using Telnet from the CLI. Network Configurations
See the switch software...
Hardware Installation Guide - Page 36
... to those switches, see Chapter 3, "Switch Installation (8-Port Switches)."
Do not open. Catalyst 2960 Switch Hardware Installation Guide
2-4
OL-7075-09 Statement 1072
Warning No user-serviceable parts inside the chassis, which lists the cable specifications for
1000BASE-X and 100BASE-X SFP modules for Particulate Matter
Cisco Ethernet switches are made first and disconnected...
Hardware Installation Guide - Page 46
... their speed and duplex parameters manually set can explicitly set the speed and duplex parameters. For configuration instructions about using the CLI setup program, go to the recessed areas on both speed and duplex. • Set the port speed and duplex parameters on the bottom of the connection.
2-14
Catalyst 2960 Switch Hardware Installation Guide
OL-7075-09 Connecting...
Hardware Installation Guide - Page 48
... into place in front of the SFP module. See Figure 2-15.
2-16
Catalyst 2960 Switch Hardware Installation Guide
OL-7075-09 Installing and Removing SFP Modules
Chapter 2 Switch Installation (24- For detailed instructions on installing, removing, and cabling the SFP module, refer to a bare metal surface on the chassis.
Use only Cisco SFP modules on the module snap into the slot...
Hardware Installation Guide - Page 57
Statement 1024
Warning Ultimate disposal of the switch. Statement 1044
Warning When installing or replacing the unit, the ground connection must always be grounded.
OL-7075-09
Catalyst 2960 Switch Hardware Installation Guide
3-3 If the switch is installed in a closed or multirack assembly). • Do not place any items on the top of this product should be...
Hardware Installation Guide - Page 73
... application for troubleshooting problems: • Diagnosing Problems, page 4-1 • Clearing the Switch IP Address and Configuration, page 4-5 • Locating the Switch Serial Number, page 4-6
Diagnosing Problems
The LEDs on page 4-4
OL-7075-09
Catalyst 2960 Switch Hardware Installation Guide
4-1 See the software configuration guide and the switch command reference on Cisco.com or...
Hardware Installation Guide - Page 76
...error-disabled, disabled, or shutdown status on one or the other cabling, or a port issue could cause this situation, the switch bandwidth is not disabled or for some reason powered off.
Diagnosing Problems
Chapter 4 Troubleshooting
Port and Interface Settings... frames, crowding out legitimate traffic. Catalyst 2960 Switch Hardware Installation Guide
4-4
OL-7075-09 Make sure that ...
Hardware Installation Guide - Page 77
....
To troubleshoot autonegotiation problems, try to manually set to autonegotiate. See Appendix B, "Cable and Adapter Specifications." Autonegotiation and NIC Cards
Problems sometimes occur between the switch and third-party network interface cards (NICs). Press and hold the Mode button (see Figure 1-23 on page 1-15). OL-7075-09
Catalyst 2960 Switch Hardware Installation Guide
4-5
The...
Hardware Installation Guide - Page 98
... the POST completes successfully, the System LED remains green. The other LEDs remain solid green.
POST failures are connecting the switch to a Cisco redundant power system (RPS), refer to display the setup program prompt.
If you started the terminal emulation program before you plan to use the Network Assistant to a grounded AC outlet.
Entering...
Hardware Installation Guide - Page 107
... 2-2, 3-2 lightning activity 2-2, 3-2 local and national electrical codes compliance 2-4, 3-3 more than one power supply 3-3 no user-serviceable parts 2-4 overheating prevention 2-2, 3-1 plug-socket combination 2-3 PoE 3-2 power supplies 2-3 prevent bodily injury 2-3, 2-6, 3-2, 3-15 product disposal 2-3, 3-3 rack-mounting 2-3, 2-6, 3-2, 3-15
Catalyst 2960 Switch Hardware Installation Guide
IN-5
Cisco WS-C2960S-48FPS-L Reviews
We have not received any reviews for Cisco yet.