Cisco WS-X4606-X2-E - Line Card Expansion Module Support and Manuals
Get Help and Manuals for this Cisco item
This item is in your list!
View All Support Options Below
Free Cisco WS-X4606-X2-E manuals!
Problems with Cisco WS-X4606-X2-E?
Ask a Question
Free Cisco WS-X4606-X2-E manuals!
Problems with Cisco WS-X4606-X2-E?
Ask a Question
Cisco WS-X4606-X2-E Videos
Popular Cisco WS-X4606-X2-E Manual Pages
Hardware Maintenance Manual - Page 3
... license to any installation, handling, maintenance, or operating instructions supplied by Cisco, (3) has been subjected to restrictions as authorized by the Government is subject to unusual physical or electrical stress, misuse, negligence, or accident, (4) is error free or that Customer will substantially conform to everyone are service marks, and Cisco, Cisco Systems, EtherSwitch...
Hardware Maintenance Manual - Page 4
... and supporting documentation are provided with the then-current return material authorization (RMA) procedures. Upon any termination of this License at any time by Cisco, (2) has not been installed, operated, repaired, or maintained in Technical Data and Computer Software clause at Cisco's option and through a Sales or Service Partner if necessary, to either (i) provide advance replacement...
Hardware Maintenance Manual - Page 15
... contains the initial site preparation, installation, troubleshooting, and selected upgrade and maintenance procedures.
Audience
This publication is included in your local sales representative or call Customer Service. About This Manual xv Note To order UniverCD, Cisco's online library of the Cisco 4000 series features
and physical specifications.
• Chapter 2, "Preparing for...
Hardware Maintenance Manual - Page 16
... Hardware Configuration," includes a troubleshooting
overview, problem-solving instructions, environmental reporting features, and understanding front-panel and network-processor module LED indicators.
• Chapter 5, "Maintaining and Upgrading the Router," includes instructions for opening the
chassis, replacing or adding network processor modules, and replacing single in-line memory modules...
Hardware Maintenance Manual - Page 20
... (FDDI), ISDN BRI, G.703, channelized T1/PRI, channelized T1/PRI, and ATM modules. Series Specifications
Figure 1-1 shows the front panel of the single and dual Token Ring, dual Ethernet, and FDDI modules.
1-2 Cisco 4000 Series Hardware Installation and Maintenance The Cisco 4000-M can support only one is present. For optimum heat dissipation, use the center slot position...
Hardware Maintenance Manual - Page 22
... 4000 Series Virtual Configuration Register," the appendix "Cisco 4000-M ROM Monitor," and the appendix "Cisco 4500-M and Cisco 4700 ROM Monitor.")
Figure 1-2
Cisco 4000 Series Memory Systems and Software Images
Cisco 4000 and Cisco 4000-M
EPROM-based
Flash-memory based
Boot helper (xboot)
Cisco IOS
ROM monitor
Cisco 4500, Cisco 4500-M, Cisco 4700, and Cisco 4700-M
EPROM-based
Flash...
Hardware Maintenance Manual - Page 43
... in NRZI mode. An error message will be generated if there is not configured. To set , or if the cable is DCE and the clock rate is a mismatch between the cable and the software configuration of the dte-invert-timing command must be manually changed. Figure 2-22 Dual Serial Network Processor Module Jumpers, J4 and J5...
Hardware Maintenance Manual - Page 54
... that supports ISDN PRI. By default, the CE1 module is presented to 120-ohm.
2-32 Cisco 4000 Series Hardware Installation and Maintenance On the CE1, the controller provides up to 120-ohm or 75-ohm. To set capacitive coupling between the chassis and external devices, as described in the G.703 specification. Each virtual channel is set to...
Hardware Maintenance Manual - Page 55
... 2
J5, J71
2 and 3
Sets cable impedance to 120-ohm Sets cable impedance to AC. All of these jumpers must be configured by trained service personnel only. For the CE1 module, four serial cables are available from Cisco Systems. All three have DB-15 connectors on the CE1end and either impedance option, a jumper installed at J2 bypasses the...
Hardware Maintenance Manual - Page 67
...approved for such apparatus, or covered by a General Approval. The BRI network processor module is regarded as a BRI module connection. Installation Requirements (Special Considerations) Read the following subassemblies:
• BRI network processor module mother card (part number 73-1219) • 1 or 2 BRI adapter interface cards (part number 73-1220) • BRI-ISDN (point-to-point use of...
Hardware Maintenance Manual - Page 74
...prompt, specify the interface, serial, unit number, and channel-group to configure the new CE1 module. Press the Return key after each step. Router(config-controller)# framing crc4...the configuration mode.
3-16 Cisco 4000 Series Hardware Installation and Maintenance
End with the ip address configuration subcommand as follows:
Router# conf t Enter configuration commands, one per line.
...
Hardware Maintenance Manual - Page 88
... command, see the appropriate Cisco IOS software publication.)
Note An error message will be generated if there is not configured.
Figure 4-9
Dual Serial Port LED Card-Side View
XX Serial LED 78-0851-01 REV
DO TXC DI RXC
DCD RS TS1 TS2
LP DCE
H1046a
4-8 Cisco 4000 Series Hardware Installation and Maintenance Note the locations...
Hardware Maintenance Manual - Page 123
...-second window, you set the configuration to the ROM monitor prompt. Cisco 4000-M ROM Monitor C-1 The ROM monitor prompt is provided. If you set the software configuration register (bits 3, 2, 1, and 0) to zero, you can break to 0x0, you must manually boot the system each time you isolate or rule out hardware problems encountered when installing your router. Timesaver...
Hardware Maintenance Manual - Page 127
... value, 0x0, takes effect after the router is configured to be off by setting the configuration register. The Cisco 4500-M and Cisco 4700 ROM monitor supports more features than the familiar Cisco 4000-M ROM monitor. During the 60-second window, you isolate or rule out hardware problems encountered when installing your router. The ROM Monitor can help initialize the processor...
Hardware Maintenance Manual - Page 141
... 4-8 power LED indication 3-22 light 4-3 specifications 1-3 supply features 2-4 system, troubleshooting 4-2 preparing for installation 2-1 to make connections 2-7 preventing ESD damage 2-3 preventive site configuration 2-4 printing summary of ROM monitor commands problem indications 4-3 temperature 4-3 problem solving 4-1 processor specifications 1-3 protocol analyzer, attaching 2-9 publications...
Cisco WS-X4606-X2-E Reviews
Do you have an experience with the Cisco WS-X4606-X2-E that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!