Dewalt DWS716 Support and Manuals
Get Help and Manuals for this Dewalt item
This item is in your list!
View All Support Options Below
Free Dewalt DWS716 manuals!
Problems with Dewalt DWS716?
Ask a Question
Free Dewalt DWS716 manuals!
Problems with Dewalt DWS716?
Ask a Question
Dewalt DWS716 Videos
Popular Dewalt DWS716 Manual Pages
Instruction Manual - Page 3
...This instruction manual uses the following safety alert symbols and words to alert you have any questions or comments about this or any DeWALT tool, call us toll free at: 1-800-4-DeWALT (1-800-433-9258).
1 A
DWS716XPS ...bevel stop override levers 21 Vertical material clamp 22 Miter detent override 23 CUTLINE LED On/Off switch
(DWS716XPS only)
WARNING! DANGER: Indicates an imminently hazardous...
Instruction Manual - Page 4
... warnings, instructions, illustrations and specifications provided with this saw to cut...miter saw becoming unstable. in the workpiece. Abrasive dust causes moving parts such as additional support...replacement parts. Then work area clean and well lit.
Use of dust collection can cause severe injury within a fraction of cutting either side of the miter saw table can be repaired...
Instruction Manual - Page 5
...Sets
Volts
Total Length of this tool to prevent damage to hearing loss.
• Air vents often cover moving parts...miter saws. The polycarbonate material used in working order.
• ALWAYS USE THE KERF PLATE AND REPLACE... ALL WIRING CODES and recommended electrical connections to the instructions. Your risk...saw blade, increasing the risk of it is completely assembled and installed...
Instruction Manual - Page 6
... any adjustments or removing/installing attachments or accessories. Specifications
Capacity of power and overheating. Width 1.6" (40.6 mm)
Resulting Height 7.1" (180.3 mm)
45º bevel -
A)
WARNING: Never modify the power tool or any part of injury, keep thumb underneath the handle when pulling the handle down. Intended Use This heavy duty miter saw is designed for...
Instruction Manual - Page 7
...
27
Installing a Blade 1. Return the guard bracket to its original position and the screw tightened before activating the saw. • Failure to access the blade screw 34 . Loosen, but do so may be raised far
enough to do not remove guard bracket screw 39 until the miter detent locks it at this miter saw. Lower...
Instruction Manual - Page 8
...mum workpiece support, without ...serviced by giving the saw . Always be raised by hand when installing or removing saw...saw has been designed to clear. NOTE: The guide groove of the guard is not adjustable. If the guide...MANUALLY UNLESS THE SAW IS TURNED OFF. A, J)
NOTE: Adjust the bevel angles only after performing the 0° bevel angle and bevel pointer adjustment. • To set...
Instruction Manual - Page 9
... operation. Fig. A) DWS716XPS ONLY NOTE: The miter saw , unlock miter lock lever 5 by pulling the knob out and rotating it from the kerf. The saw is equipped to a non-detent miter angle. Flip the crown bevel pawl so the 30° text is functioning properly, re-lock miter lock handle to accurately and rapidly set a crown stop at...
Instruction Manual - Page 10
...) blade and a slower, even cutting rate will reduce the saw . Quality of cut The smoothness of recommended saw table or to the list of any angle. For varied cutting applications, refer to help feed, support or pull the workpiece. The left with the miter arm set up can be purchased at extra cost. Sketch A in...
Instruction Manual - Page 11
... example, the closest degree mark on the miter scale, as shown in Figure R. For settings that angle on saw (42°). The vernier scale allows you in the miter scale. Turn off miter saw is inscribed with the CLOSEST degree mark on the miter scale happens to
get miter
angle setting on the appropriate arc in the chart. the...
Instruction Manual - Page 12
... side of cut
Material up to fine tune your local DeWALT retailer or DeWALT service center. Save right side of cut
Right side
1. Cutting Crown Molding
Your miter saw , as shown in Figure X. Instructions for crown moldings are available at which goes against the wall when installed) is against the fence and the top of the molding...
Instruction Manual - Page 13
... replace ...models...Saw Blades under Accessories for miter saws. Never use of the sawdust produced. Periodically clean all air vents with some dust will capture the majority of such accessories with this procedure.
WARNING: Never use blades designed for cleaning the non-metallic parts of service center locations is extremely important when making any adjustments or removing/installing...
Instruction Manual - Page 14
... speed Machine vibrates excessively Does not make accurate miter cuts
Material pinches blade 12
Troubleshooting Guide
BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS
WHAT'S WRONG? Some states do not allow us to products sold in Latin America, see country specific warranty information contained in case there is a problem with your product. • CONFIRMATION OF OWNERSHIP...
Instruction Manual - Page 15
English
SET THIS MITER ANGLE ON SAW ANGLE OF SIDE OF BOX (ANGLE A)
TABLE 1: COMPOUND MITER CUT (POSITION WOOD WITH BROAD FLAT SIDE ON THE TABLE AND THE NARROW EDGE AGAINST THE FENCE)
10 20
30
40
10 20
10 20 30
30
40
6-SIDED
50
BOX
40
8-SIDED
50
BOX
60
60 70 80
70 80
50
SQUARE BOX
60
70
80
SET THIS BEVEL ANGLE ON SAW
13
Instruction Manual - Page 44
N748087 DWS716, DWS716XPS Copyright © 2018, 2019 DeWALT
The following are trademarks for one or more DeWALT power tools: the yellow and black color scheme, the "D" shaped air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of lozenge-shaped humps on the surface of the tool. DeWALT Industrial...
Dewalt DWS716 Reviews
Do you have an experience with the Dewalt DWS716 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Dewalt yet.
Earn 750 points for your review!