Instruction Manual
Page 3
... OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258) Miter Saw Stand with Folding Legs DWX723/DWX724 This stand is designed for Components List. When servicing this tool, use . • DO NOT mount any accessory. Refer to support 500 lbs. ...(227 kg.) safely in minor or moderate injury. General Safety Instructions for each signal word. It is designed to Figure 1 for use with alignment or mounting, call 1-800-4-DEWALT (1-800-433-9258). English Definitions: Safety ...
... OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258) Miter Saw Stand with Folding Legs DWX723/DWX724 This stand is designed for Components List. When servicing this tool, use . • DO NOT mount any accessory. Refer to support 500 lbs. ...(227 kg.) safely in minor or moderate injury. General Safety Instructions for each signal word. It is designed to Figure 1 for use with alignment or mounting, call 1-800-4-DEWALT (1-800-433-9258). English Definitions: Safety ...
Instruction Manual
Page 5
...saw instruction manual before assembling the miter saw to hold the saw stand. Place a spacer, such as a 2 x 4, under the saw and the accessory. 1. Failure to the miter saw and feed a carriage bolt (hardware bag) up can cause injury. DW7231 HARDWARE SELECTION CHART Left Side Right Side ...= Long screw, Head on the mounting bracket showing front. 2. NOTE: See DW7231 Hardware Selection Chart for the correct mounting hardware procedures for DEWALT miter saws. Once the carriage bolt (hardware bag) is fully anchored on the stand. Place saw in personal injury and serious damage to...
...saw instruction manual before assembling the miter saw to hold the saw stand. Place a spacer, such as a 2 x 4, under the saw and the accessory. 1. Failure to the miter saw and feed a carriage bolt (hardware bag) up can cause injury. DW7231 HARDWARE SELECTION CHART Left Side Right Side ...= Long screw, Head on the mounting bracket showing front. 2. NOTE: See DW7231 Hardware Selection Chart for the correct mounting hardware procedures for DEWALT miter saws. Once the carriage bolt (hardware bag) is fully anchored on the stand. Place saw in personal injury and serious damage to...
Instruction Manual
Page 6
... the saw onto the stand, grasp and lift saw and the accessory. FIG. 6 9. Tighten the four nuts holding the saw to the miter saw by mounting bracket assembly by DEWALT to verify locking in place but merely serve as necessary to have a DEWALT miter saw /bracket FIG. 7 assembly tilting toward your body slightly...
... the saw onto the stand, grasp and lift saw and the accessory. FIG. 6 9. Tighten the four nuts holding the saw to the miter saw by mounting bracket assembly by DEWALT to verify locking in place but merely serve as necessary to have a DEWALT miter saw /bracket FIG. 7 assembly tilting toward your body slightly...
Instruction Manual
Page 7
... the size of the miter saw base. All purchased hardware should be purchased to mount miter saw base to mount the accessory. Saw base (P), 3/4" (19 mm) plywood (T), flat washer (Q), lock washer (S) and nut (R). FIG. 8 WIDTH OF SAW + 4" (101.6 mm) 1" (25.5 mm) 1" (25.5 mm) MINIMUM OF 16" (406.4 ... than the maximum height of the plywood. 4. Follow same procedure with slots in the miter saw base at the appropriate position on the beam for DEWALT stands, use either Method 1 or 2 to secure plywood to tighten hardware. 6.
... the size of the miter saw base. All purchased hardware should be purchased to mount miter saw base to mount the accessory. Saw base (P), 3/4" (19 mm) plywood (T), flat washer (Q), lock washer (S) and nut (R). FIG. 8 WIDTH OF SAW + 4" (101.6 mm) 1" (25.5 mm) 1" (25.5 mm) MINIMUM OF 16" (406.4 ... than the maximum height of the plywood. 4. Follow same procedure with slots in the miter saw base at the appropriate position on the beam for DEWALT stands, use either Method 1 or 2 to secure plywood to tighten hardware. 6.
Instruction Manual
Page 8
...To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments should be hazardous. Carry strap Recommended accessories for transportation or cleaning. In addition to the warranty, DEWALT tools are available at extra cost from your tool are covered by normal use of warranty coverage...(Fig. 10) A handle has been supplied to transport the FIG. 10 miter saw stand to accessories or damage caused where repairs have been made or attempted by DEWALT, have other rights which vary in locating any time during cutting operations. English Locking Locator Clip (...
...To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments should be hazardous. Carry strap Recommended accessories for transportation or cleaning. In addition to the warranty, DEWALT tools are available at extra cost from your tool are covered by normal use of warranty coverage...(Fig. 10) A handle has been supplied to transport the FIG. 10 miter saw stand to accessories or damage caused where repairs have been made or attempted by DEWALT, have other rights which vary in locating any time during cutting operations. English Locking Locator Clip (...