Dewalt DWX726 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DWX726 manuals!
Problems with Dewalt DWX726?
Ask a Question
Free Dewalt DWX726 manuals!
Problems with Dewalt DWX726?
Ask a Question
Most Recent Dewalt DWX726 Questions
Can I Replace The Raise And Release Cables
(Posted by DonBaileypainting 1 year ago)
How Do I Adjust The Release Cabl
(Posted by paswansonsr1950 2 years ago)
Support Arms
Ounce I slide the support arms in.How do I take them all the way out?
Ounce I slide the support arms in.How do I take them all the way out?
(Posted by jstevens057 2 years ago)
How To Adjust Cable To Release Mechanism
just put together the dwx726. The release cable too loose the fully disengage and allow the stand to...
just put together the dwx726. The release cable too loose the fully disengage and allow the stand to...
(Posted by Jacsjmac 2 years ago)
Dewalt DWX726 Videos
DeWALT DWS780 12" Double Bevel Sliding Compound Miter Saw and the DWX726 Rolling Stand
Duration: 7:29
Total Views: 105,576
Duration: 7:29
Total Views: 105,576
DEWALT Rolling Miter & Planer Stand DWX726 REVIEW
Duration: 4:13
Total Views: 12,995
Duration: 4:13
Total Views: 12,995
Popular Dewalt DWX726 Manual Pages
Instruction Manual - Page 3
... product was designed to provide portability for miter saws and planers. Follow the mounting instructions carefully. Also use only identical replacement parts. DANGER: Indicates an imminently hazardous situation which , if not avoided, may result in the shop. This Rolling Miter Saw/Planer Stand is dusty. If you have any accessory. When servicing this tool, use face or dust mask...
Instruction Manual - Page 4
Components (Fig. 1)
WARNING: Never modify the stand or any part of the stand.
Damage or personal injury could result. WRENCH ... do not raise or lower stand until the assembly of the extension work support assembly 1 Handle 2 Wheel 2 Axle 2 Work support arms (1 with mineral spirits, paint thinner or denatured alcohol. English
Carton Contents
1 Rolling miter saw/planer stand 1 Leg extension 1 ...
Instruction Manual - Page 5
... of the wheels (D) on the axle and attach the nut (R). Align the holes and install two M8 x 15 mm buttonhead screws (L)
N
with the supplied hex wrench. With stand still upside down, insert the wheel/storage-foot connector (N) to be tightened completely later in the same manner. English
1. Continuing with the longer side...
Instruction Manual - Page 6
...the storage-foot connector screws that were
loosely installed in storage foot and storage foot connector. Place your left hand to two heights. The stand will adjust to push down , attach the...the next height setting.
After raising the stand a few inches, release the red activating lever.
S
4 Tighten screws securely with the supplied hex wrench. TO RAISE AND LOWER THE STAND (FIG. 8) ...
Instruction Manual - Page 7
... outside of the "T" in Figure 9. Insert the assembled extension work support arm (B) hole. Repeat for other extension work support into the hole (Z) from disengaging. FIG. 9
FIG. 10
W
H H1
E
ATTACHING THE EXTENSION WORK SUPPORTS (FIG. 9, 10) IMPORTANT: Be sure the longer side of stand. Refer to the red activating lever. Place the washer and nut...
Instruction Manual - Page 8
... a stand or supporting surface. Place miter saw or planer to the tool.
English
2. Refer to your tool manufacturer's
instructions regarding...miter saw or planer off, disconnect the tool from the mounting rails. Center the tool, both the instructions in STEP 1) through each of your tool manufacturer's manual before assembling the miter saw or planer on the stand.
4. If this manual...
Instruction Manual - Page 9
...of 3/4 inch (19 mm) plywood (See Figure 15 for dimensions). PRODUCT STABILITY TEST (FIG. 16-17) The rolling miter saw or planer to align with a non-warped, even piece of 16 inch (406.4 mm). English
WARNING: STABILITY ... plywood. If binding and/or inaccuracy occurs, replace the plywood with the slots in the mounting rails, mount the miter saw /planer stand is not warped or uneven.
Instruction Manual - Page 10
...-up can cause injury. All sliding compound miter saws MUST be raised on all miter
saws, compound miter saws and sliding compound miter saws.
If the stand tends to tip to the front, reposition...of
the stand so that the
front leg is turned
off and disconnected
from power source before installing and removing accessories, before adjusting or changing setups or when making repairs. Place ...
Instruction Manual - Page 11
.... 18) 1.
FIG 18
TO ADJUST EXTENSION WORK SUPPORT HEIGHT 1. The stand may raise unexpectedly when lever is released.
Tighten the vertical lock knob. 4. STORAGE AND TRANSPORTATION
WARNING: TIPPING HAZARD. Refer to the desired height. Refer to To Raise and Lower the Stand under Assembly to adjust the stand to Figure 19 for proper transporting position...
Instruction Manual - Page 12
...
WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use identical replacement parts. Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments should be performed by a DEWALT factory service center, a DEWALT authorized service center or other qualified service personnel. To reduce the risk of purchase with this...
Instruction Manual - Page 13
English
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-4-DEWALT (1-800-433-9258) for a free replacement.
11
Instruction Manual - Page 40
... on the handgrip; and the array of the tool. the "D" shaped air intake grill; the kit box configuration; DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (JUN11) Part No. N116787 DWX726 Copyright © 2011 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme;
Dewalt DWX726 Reviews
We have not received any reviews for Dewalt yet.