Fantec MR-35HDC Support and Manuals
Get Help and Manuals for this Fantec item
View All Support Options Below
Free Fantec MR-35HDC manuals!
Problems with Fantec MR-35HDC?
Ask a Question
Free Fantec MR-35HDC manuals!
Problems with Fantec MR-35HDC?
Ask a Question
Popular Fantec MR-35HDC Manual Pages
Manual - Page 1
FANTEC MR-35HDC HARD DISK COPYSTATION
POWER
Red=RAID Blue=Dup
RAID0 RAID1 BIG JBOG
Copy Compare Prescan Erase
Start Mute Reset
RAID DUP
USER MANUAL
Manual - Page 2
...Serial ATA HDD ...15 4.3 Four Working Mode ...15 4.4 Support system Windows 2000/XP/VISTA & Mac os 9.0 or ...flash.
(7) Press the "Start" button for two times. Package contens FANTEC MR-35HDC User manual AC Cable USB 2.0 Cable
1
22 Package contents ...22
8. NOTE ...... LED will beep for more than the "Source-HDD".
(2) Set the function switch to "DUP" (Duplicate) operation and mode switch...
Manual - Page 3
...Erase-LED" will stay green. Troubleshooting
EVENT
EFFECT
No HDD detected or HDD failed Detection OK HDD access
HDD Read Failure Copy error
Compare error
Prescan error
Erase error
HDD Status LED will send ...than the SourceHDD, the remaing space will twinkle in DUP function (duplicate)
ATTENTION:
Please set the switch to DUP operation.
Front
POWER
Red=RAID Blue = Dup
RAID
RAID0 RAID1...
Manual - Page 4
...lock at the instructed point , then you change the HDD in slot 1 was replaced (due to... Rebuild after power off the device without connection to install/ unload the hard disk. 2. RAID Fail = ...Troubleshooting: (1) HDD Status LED (left side) a. Mode no action = twinkle in RAID function
ATTENTION:
Please set the switch to end the buzzer beep.
6. After your PC detects the FANTEC MR-35HDC...
Manual - Page 5
...host through USB, turn on the power and press the "Start" button (Instruction will beep for data usage. Before extend:
2. Quick Start Operation in ...-240V
(1) Pull the doorknob to insert hard disks.
(2) Set the function button to BIG, BIG LED will keep bright, and...entering the RAID1 active status. After using the disk part utility to your selected RAID mode. Now the system...error.
4
Manual - Page 6
... material transmission completes when LED sends the blue light
The following LED condition will be updated to display the existing volumes on the computer.
4.
The material transmission completes when HDD2...light and the HDD1 LED continue glittering in turn with blue& red lights. In this manual. Under the material transmission condition: The HDD1 LED glitters with purple light, and the HDD2...
Manual - Page 7
.... Please check and see if the HDD has installed correctly. 2. The resulting storage capacity of the ...time to
17
6 Additional third-party products (such as follow:
4.4 Support system Windows 2000/XP/VISTA & Mac os 9.0 or above version ...replace formatted HDD instead. USB&Power Cable were connected; For Windows 2000 or Windows XP Home Edition, you must download the "disk part...
Manual - Page 8
... hard disk operating speed by using only a single hard disk drive connected to Port 0, and then increase the storage capacity of Port 1 will get a single driver letter if each hard drive to create a BIG volume using many disks in parallel. Opening the power switch, pulling MODE switch to BIG and press...
Manual - Page 9
USB Features The FANTEC MR-35HDC provides the following Universal Serial Bus (USB) features: USB 1.0 and USB 2.0 specification compliance For detailed information about USB ...virtual drives are imposed by a clew to RAID0 and press START button. Hard drive A and B are installed. Re-zoning which format). BIG The BIG storage policy concatenates a series of the physical hard drives A and...
Manual - Page 10
.... NOTE : 1. Press power switch, set MODE switch to acknowledge the warning. Features 4.1 High speed external storage solution, USB2.0 480 Mbps SATA Features The FANTEC MR-35HDC provides the following Serial Advanced Technology Attachment (SATA) features: Automatic negotiation between SATA I (1.5Gbps) and SATA II (3.0 Gbps) Serial ATA 2.5 specification compliance (Gen2m) For detailed...
Manual - Page 11
... your data and drag the old drive to the trash to open the Windows Disk Manager.
3. 8. Refer to the new configuration. 1. Review the file system settings and click Finish to create the logical partition.
Fantec MR-35HDC Reviews
We have not received any reviews for Fantec yet.