Fender MA6 Mixer Amplifier Support and Manuals
Get Help and Manuals for this Fender item
This item is in your list!
View All Support Options Below
Free Fender MA6 Mixer Amplifier manuals!
Problems with Fender MA6 Mixer Amplifier?
Ask a Question
Free Fender MA6 Mixer Amplifier manuals!
Problems with Fender MA6 Mixer Amplifier?
Ask a Question
Popular Fender MA6 Mixer Amplifier Manual Pages
Owners Manual - Page 3
...
•
Depth Height
23 Inches 7.5 Inches
58.0 cm 19.0 cm
13.5 Inches 36.5 Incnes
34.0 cm 93.0 cm
P.O. PHYSICAL DIMENSIONS (APPROXIMATE, FOR SHIPPING PURPOSES)
MIXER AMPLIFIER
SPEAKER COLUMN
U.S. •
MA6
MIXER AMPLIFIER
OPERATION INSTRUCTION MANUAL
BY
d
MADE IN U.S.A.iSts°1.°
•
it141 zittl;id .
Owners Manual - Page 5
... Output
7
1
Speaker Fuse
7
1
Accessory AC Outlet
7
3 3
Line Cord Receptable Circuit Breaker
7 7
3 SECTION II
3 Setting Up The System
8
3
Speaker Placement
8
3
Speaker Connection
8
3
Microphones
8
3
AC Power Cord
8
3
Preliminary Control Settings
9
5
Final Control Adjustments
9
5
Volume
9
5
Tone
9
5
Master Section Reverb Return and Effects
5
Return Switches...
Owners Manual - Page 6
... Section Level Controls
4
7 Equalizer Controls and VU Meter
5
8 Equalizer Response Curves 9 Master Section Effects, Direct Inputs, Reverb Jacks
• 6
6
10 Rear Panel
7
11 Typical Stage Setup
8
12 Speaker Connections
8
13 Effects Jack Connections
10
15 Typical Speaker, Monitor, and Tape Recording Connections
11
16 MA6 System with Auxiliary and Monitor Speakers...
Owners Manual - Page 7
... frequency compression
•
driver with six input
channels and two output channels, a reverb unit, a 200
watt power amplifier, and two speaker system...MANUAL.
•
The remaining pages of this Manual detail the functions of a mixer with associated horn and crossover network mounted in
one compact package, hereafter referred to as the
"Mixer." •
INTRODUCTION
The Fender...
Owners Manual - Page 8
... of the Mixer to provide the optimum signal-to that channel. Normally, once the Gain Control has been set . Treble Control (Fig. 3 - Pre-Amp Section (one preamplifier is shown, the actual System has...high frequency content of the input signal. Item 6) is just flickering, the control is properly set , it will not need to avoid audible distortion.
INPUT
LO2 INPUT
INPUT AMP
GAIN
BASS CONTROL...
Owners Manual - Page 10
... the internal reverb unit (or an auxiliary unit if one is independent of the Channel Level control so that is, the level of the summing amplifier thereby preventing it from this control clockwise from the center detented position sends the signal from overloading. Item 4)
Turning this channel to the Effects/ Reverb...
Owners Manual - Page 12
...chaining additional mixers. This jack allows use of the five controls is useful for the Monitor summing amplifier.
4 f'14Pa isvaniarrimemmgmeimor.vv:
NIMUMILINP
-FLAT
Each channel is provided with a three pin low...- Equalizer Controls and VU Meter
Item 1) This jack allows connection of the internal power amplifier. Item 6)
Controls the amount of 50 to be used at any one time on ...
Owners Manual - Page 13
...) providing that the Eff/ Rev knob (Fig. 3 - Equalizer Response Curves
5K
10K
20K
MAN
Send (Fig. 9 -
It functions only if the front panel controls are set to the Effects Return control. Item 3)
This jack is used to send the signal from the external effects device and routes the signal to provide...
Owners Manual - Page 14
...red button.
5
4
7 8
9 T
FIGURE 10 - Line Cord Receptacle (Fig. 10 - Item 10) Connection for storage of an amplifier failure and protects the amplifier from a low impedance load. Circuit Breaker (Fig. 10 - • AUXILIARY JACKS (Rear Panel)
Auxiliary Reverb Send (Fig. 10 - ...ohms.
Monitor (Pre-Amp) Output (Fig. 10 - Item 9)
This can be replaced only with the speaker jacks.
Owners Manual - Page 15
...
Microphones
High impedance microphones plug into the Lo-Z 3 pin connectors (Fig. 5 Item 1). •
SECTION II SETTING UP THE SYSTEM
Speaker Placement
Placing the speakers forward of the microphones (Fig. 11) will cause a loss of volume. Typical Stage Setup
FROM SPEAKER 12) JACKS
os
P
E
A
MA6
A
K
MIXER
K. Item 2).
Low impedance microphones plug into the...
Owners Manual - Page 16
...Item 8). Item 6) to feedback or ring. Item 3) (Fig. 6 - Item 6). Item 8).
7. Set the Channel Level controls (Fig. 5-Item 3) for the monitors. The Gain control is singing into the ...- These equalizers are some reverb (through the Monitor speakers. Exam- Item 2 and 3) to set to glow, indicating overload of the Channel. If external effects are "ahead" of the Mixer ...
Owners Manual - Page 17
... the Effects Send jack can be connected to the input of the signal processing device and the output of an Additional Mixer (Fig. 13)
The Fender MA6 can be used as Submasters. Item 5) should be used for several functions. DIRECT INPUTS MONITOR^
FIGURE 13 - Phasers, Flangers, Delay lines, or other mixer...
Owners Manual - Page 18
...Connect the Pre-Amp Output jack (Fig. 10 Item 4) to the Effects Receive jack (Fig. 9 - amplifier which could be used for highs, reverse the System.
Pre-Recorded Tapes
To play back pre-recorded tapes,... the tape recorder to one of
the crossover to the Input of less than 4 ohms. Replace the fuse only with Auxiliary and Monitor Speakers Tape Recording (Fig. 18)
1.
Speaker Output ...
Owners Manual - Page 20
... 12" low frequency speakers mounted in parallel will provide the desired 4 ohm amplifier load.
•
•
FIGURE 19 - Speaker Column An internal crossover... Speaker Enclosure System (Fig. 19)
The Fender MA6 Public Address System is 8 ohms. The two speaker systems connected in a Thiele aligned vented box enclosure and a compression driver mid and high frequency horn. The electrical ...
Fender MA6 Mixer Amplifier Reviews
Do you have an experience with the Fender MA6 Mixer Amplifier that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Fender yet.
Earn 750 points for your review!