Fender SRA 400 Stereo Power Amplifier Support and Manuals
Get Help and Manuals for this Fender item
This item is in your list!
View All Support Options Below
Free Fender SRA 400 Stereo Power Amplifier manuals!
Problems with Fender SRA 400 Stereo Power Amplifier?
Ask a Question
Free Fender SRA 400 Stereo Power Amplifier manuals!
Problems with Fender SRA 400 Stereo Power Amplifier?
Ask a Question
Popular Fender SRA 400 Stereo Power Amplifier Manual Pages
Owners Manual - Page 3
SRA 400
STEREO POWER AMPLIFIER
OPERATION INSTRUCTION MANUAL
BY
MADE IN U.S.A.
System 43 pounds 19 inches 17.3 inches 5.25 inches
Metric System 19.5 kg 48.3 cm 44.0 cm 13.3 cm
P.O. flukes
A
CHI
MY. ...
Owners Manual - Page 4
...1 1
1 1 1 1 2 2 2 2
SECTION II SETTING UP THE SYSTEM Sound System Connections Rack Mounting Instructions Speaker Connection Stereo Program Connection Monophonic Connection Monophonic/Monitor Connection Stereo Bi-amplified Connections Monophonic Bi-amplified Connection Bridged Output Connection SECTION III Sound System Connections Preliminary Operating Sequence SRA 400 General Specifications
PAGE...
Owners Manual - Page 5
... for each channel. Sixteen 250 watt power transistors are mounted on a massive tunnel heatsink with 22 steps, calibrated to indicate amplifier gain in road travel.
BEFORE ATTEMPTING TO USE THE UNIT, FAMILIARIZE YOURSELF WITH THE INFORMATION CONTAINED IN THIS MANUAL.
These input attenuators allow for predictable and repeatable set-ups, accurate input sensitivity adjustments...
Owners Manual - Page 6
...The O VU CAL position indicates the calibrated setting at which O VU (1.23 volts RMS) will shut off AC power in the event of the amplifier is turned on each channel are unbalanced and ...
These electronic displays respond quicker than 4 ohms.
CHI
GAIN
8. The displays are color coded, with the red LED indicating full power. SRA 400 REAR PANEL
CHANNEL 1 INPUT (Fig. 2 - CHANNEL 1 OUTPUT (Fig...
Owners Manual - Page 7
...:
TO REDUCE THE RISK OF ELECTRICAL SHOCK. The input is 8 ohms. Operation into a single channel 400 watt amplifier. The load is not blocked during operation. SET MODE SWITCH TO BRIDGED. USE CH I INPUT. SA Ft
FIGURE 2 - REPLAC
ONLY WITH SAME TYPE 6A . 250V FUSES. CHANNEL 1 OUTPUT FUSE (Fig. 2 -
This mode eliminates the use...
Owners Manual - Page 8
...power amplification, and offers some of speaker cable (over 25 feet),#16 AWG or larger wire is recommended. SECTION II SETTING UP THE SYSTEM
SOUND SYSTEM CONNECTIONS
The SRA 400 is a stereo (two channel) amplifier and special care must be taken in setting... support is...install the screws into one channel's pair of output jacks (a parallel connection resulting in this purpose. The normal set...
Owners Manual - Page 9
... 400 channel 1 output is connected to the high frequency driver (tweeter) of the SRA 400 power amplifier in Figure 7, the SRA 400 was chosen as a 400 watts single channel amplifier. In this stereo system one program channel of a mixer, can also be as powerful as a monophonic bi-amplified system. Set mode switch to channel 1 input. Both channels will...
Owners Manual - Page 10
... 2 IN CH 2 OUT
LEFT SPEAKER
(MONO INFO)
RIGHT SPEAKER
(MONO INFO)
MODE SWITCH SET TO MONO
FIGURE 4 - CH 1 IN
SRA 400
CH 2 IN
CH 2 OUT
LEFT SPEAKER
RIGHT SPEAKER
FIGURE 3 - PROGRAM CHL. Two Channel Output From Single Source (Monophonic) 5 SECTION III
SRA 400 STEREO POWER AMPLIFIER
SOUND SYSTEM CONNECTIONS
MIXER
CH 1 OUT
L PROGRAM CHL.
R.
Owners Manual - Page 11
...CH 1 IN
SRA 400
CH 2 IN CH 2 OUT
CH 1 OUT CH 1 IN
ADDITIONAL STEREO AMP OP' CH 2 IN
CH 2 OUT
FIGURE 6 - Stereo Bi-amplified Connection #1
6
TO TWEETER
LEFT BIAMP SPEAKER SYSTEM
TO WOOFER
TO TWEETER
RIGHT BIAMP SPEAKER SYSTEM
TO ... 1 IN
SRA 400
CH 2 IN
CH 2 OUT
PROGRAM SPEAKER
MONITOR SPEAKER
FIGURE 5 - FREQ. SRA 400 STEREO POWER AMPLIFIER SOUND SYSTEM CONNECTIONS
MIXER
PROGRAM CHL.
FREQ.
Owners Manual - Page 12
... # 2
TOTWEETER
LEFT BIAMP SPEAKER
TOWSYOSTEOMFER
JTOTWEETER
RIGHT BIAMP SPEAKER
I
CH 1 OUT ► CH 1 IN
►C1HINADDITIONAL STEREO AMP CH2201 - Monophonic Bi-amplified Connection 7 SRA 400 STEREO POWER AMPLIFER SOUND SYSTEM CONNECTIONS
HLF.LF. .RRCEEHOOQQLUU,..TT
L.CHL.INPUT L.
CROSSOVER
HLRFF..
TWO CHANNEL
MIXER
ELECTRONIC
►RC. FIGURE 7 - PROGRAM CHL. REOQU...
Owners Manual - Page 13
... hum and possible shock. Connect the sound system required for your specific application. (See Sound System Connections.)
2. Plug in line cord of the SRA 400. Turn on the sound system's mixer, and any other equipment.
4. Item 2). SECTION III
SRA 400 STEREO POWER AMPLIFER SOUND SYSTEM CONNECTIONS
MIXER
PROGRAM (MONO)
lo CH 1 IN
CH...
Owners Manual - Page 14
... CHANGE WITHOUT NOTICE"
9
SRA 400 GENERAL SPECIFICATIONS
4,0, Load
8,Q Load
Output power, continuous, per channel with no more than .09% THD (Mono or Stereo mode)
200 W
100 W
Output power, Bridged mode, continuous with no more than .18% THD
not recommended
400 W
Damping Factor at 50 Hz
65
130
Dynamic Headroom
1.9 dB
2.9 dB
Intermodulation Distortion
....
Fender SRA 400 Stereo Power Amplifier Reviews
Do you have an experience with the Fender SRA 400 Stereo Power Amplifier that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Fender yet.
Earn 750 points for your review!