Fluke 719PRO Support and Manuals
Get Help and Manuals for this Fluke item
View All Support Options Below
Free Fluke 719PRO manuals!
Problems with Fluke 719PRO?
Ask a Question
Free Fluke 719PRO manuals!
Problems with Fluke 719PRO?
Ask a Question
Fluke 719PRO Videos
Fluke 719Pro 300G Electric Pressure Calibrator
Duration: :59
Total Views: 137
Duration: :59
Total Views: 137
Fluke 719Pro 300G Bubble testing
Duration: 2:29
Total Views: 3,399
Duration: 2:29
Total Views: 3,399
CALIBRADOR DE PRESION FLUKE 719Pro 150G #PLABS
Duration: 18:38
Total Views: 698
Duration: 18:38
Total Views: 698
Fluke 719Pro 30G not holding pressure
Duration: :45
Total Views: 1,783
Duration: :45
Total Views: 1,783
Popular Fluke 719PRO Manual Pages
User Manual - Page 1
Specifications are trademarks of their respective companies. All rights reserved. All product names are subject to change without notice. 719PRO Pressure Calibrator
Users Manual
October 2013
© 2013 Fluke Corporation.
User Manual - Page 5
... 42 Command Use and Types 42 Character Processing 43
Response Data Types 44 Calibrator Status 44 Remote Commands and Error Codes 45 Enter Commands...50 Common Commands 50 Calibrator Commands 51 Ranges and Resolution 59 Maintenance...61 Replace the Batteries 61 Clean the Product...63 Clean the Valve Assembly 63 User-Replaceable Parts and Accessories 64 Specifications ...67
iii
User Manual - Page 11
... pressure sensor and innovative electrically-powered pump reach higher pressures (maximum 300 psi) and let the Product calibrate virtually any pressure device. The Product features inputs for mA, voltage, switch contacts, and an RTD probe. Contact Fluke
To contact Fluke, call one of pressure calibration options that include absolute and differential. Introduction
The 719PRO Pressure Calibrator...
User Manual - Page 43
..., push .
2. hix050.eps
33 Push to 20 mA signal. The first option sets the Port.
5. This eliminates the need for manual calculations and helps when it is 30 psi (2 Bar) FullScale and regulates a corresponding 4 mA to start the %ERROR option.
4. Push .
3.
Push to set an exact pressure with an external pump.
User Manual - Page 45
... by the user for the internal sensors, and external pressure modules. Note
The 0 % and 100 % point will be saved in the min/max registers. "MIN/MAX" is used, the 0 % and 100 % are set to toggle... until the user changes it, or if it was previously saved.
Step through the min/max values that the new min/max values will be recorded while in this mode.
Pressure Calibrator Minimum and...
User Manual - Page 49
... the "Contact Fluke" section. If not, adjust the flow computer as necessary. Note
To use a terminal program similar to Hyper Terminal, to USB interface cable, PN 4401616 must be remotely controlled with a PC terminal or by a computer program that runs the Product in Figure 11.
39 Pressure Calibrator Custody Transfer / Flow Calibration
Remote Operation...
User Manual - Page 51
... purchased separately. Select ASCII setup from File/Properties/Settings and
mark these choices: • Echo typed characters locally • Wrap lines that the Product is less than 2500 pF.
For Name enter "Fluke 719PRO". To see if the port works enter *IDN?. This command will return information on . Select Ok. 7. Pressure Calibrator Remote Operation
For remote...
User Manual - Page 54
...32768 to 32768.
719PRO Users Manual
Response Data Types
The data returned by a terminator. returns PT385_100
Indefinite ASCII (IAD)
Any ASCII characters followed by the Product can be divided into four types:
Integer
For most computers and controllers they are processed on error codes. returns FLUKE,719PRO,1234567,1.00
Calibrator Status
Error Queue
If an error occurs due to Table...
User Manual - Page 57
... limit for the indicated display
PRES_UNIT? Command LOCAL
Description
Returns user to manual operation of the Product
LOCKOUT
Locks out the keypad of the Product in remote mode
RTD_TYPE Sets the RTD type
RTD_TYPE?
Pressure Calibrator Remote Operation
Command
Description
PRES_UNIT
Set the pressure unit for percent error mode
LO_ERR
Returns the 0 % of the current being simulated...
User Manual - Page 60
...well as such. returns FLUKE,719PRO,1234567,1.00
50 Any overlapped commands are sequential. 719PRO Users Manual
Error Number
Error Description
108
Invalid sensor type
109
Pressure module not connected
110
An...overflow.
*IDN? When programs are optional. Returns the manufacturer, model number, serial number, and firmware revision of the command is at least one space required between the...
User Manual - Page 63
... ON.
is sent, it will return ON if the Product is on , send ERROR_LOOP ON.
For example:
To turn on and off loop power in error mode. Refer to do what it was meant to Tables 5, 6, 7, and 8 for more information on or off . ERROR _LOOP
Turns on error code numbers.
Pressure Calibrator Remote Operation
ERROR _LOOP?
User Manual - Page 73
... assembly. Clean the Product with a soft cloth dampened with a cotton swab soaked in the relaxed state. See the "User-Replaceable Parts" section.
1. With a small screwdriver, remove the two valve retention caps located in the repair kit, if necessary.
7.
Operate the pump handles several times and recheck for any damage or excessive wear. If shorter...
User Manual - Page 75
...[1] See www.fluke.com for more information about the test leads and alligator clips available for 719Pro and 721. Safety Sheet Quick Reference Guide User Manuals CD AA, Alkaline Batteries Bottom Plug, PRO 30, 150PSIG
71X-TRAP, Liquid Dirt Trap
Test Lead Set
Part Number 669960 4354604 4354567 4354598 376756 4365560
4380747
Variable[1]
Pressure Calibrator User-Replaceable Parts and Accessories...
User Manual - Page 77
Specifications
Pressure Measurement
719Pro-30G
719Pro-150G
719Pro-300G
Temperature effect (all ranges)
Function mA dc (simultation and measurement)...50 °C to 150 °C (-58 °F to 302 °F)
0.01 °C 0.01 °F
24 V dc
N/A
Pressure Calibrator Specifications
Accuracy
Comment
±0.025 % of full scale, 6 months ±0.035 % of full scale, 1 year
Dry air and non-corrosive ...
User Manual - Page 79
... Broadcasting & Communication
Equipment) [1] [1] This product meets requirements for use in homes.
69 This equipment is not to be used in Korea only. Pressure Calibrator Specifications
Electromagnetic Environment IEC 61326-1: Portable Electromagnetic Compatibility Applies to use in business environments and is intended for industrial (Class A) electromagnetic wave equipment
and the...
Fluke 719PRO Reviews
We have not received any reviews for Fluke yet.