Fujitsu CG01000-464802 - Scan Partner 15c Color 15ppm-bl 30 Bit SCSI Cent50 Adf Lgl Support and Manuals
Get Help and Manuals for this Fujitsu item
View All Support Options Below
Free Fujitsu CG01000-464802 manuals!
Problems with Fujitsu CG01000-464802?
Ask a Question
Free Fujitsu CG01000-464802 manuals!
Problems with Fujitsu CG01000-464802?
Ask a Question
Popular Fujitsu CG01000-464802 Manual Pages
User Manual - Page 2
... the Shipping Bracket 2-3
2.2 SCSI INTERFACE DEVICE ID 2-3 2.3 ADF PAPER CHUTE (FIGURE 2-4 2-5 2.4 ADF OUTPUT TRAY (FIGURE 2-5 2-6 2.5 DOCUMENT LOADING ...2-7 2.6 ADF SCANNING...2-8 2.7 CONNECTING THE CABLE ...2-9
3. SPECIFICATIONS 5-1
5.1 SCANPARTNER 15C SPECIFICATIONS 5-2
ii TROUBLESHOOTING 4-1
4.1 QUESTION AND ANSWER ...4-1 4.2 PAPER JAM IN THE ADF...4-3
5. Table of Contents
1.
User Manual - Page 3
... the Scanner is packed. INTRODUCTION
Congratulations on how to read through this manual. You can check all items against your "checklist", included with the proper instructions on your Scanner.
1-1 Before you with your purchase of Fujitsu Scanpartner 15C Scanner. It provides you install and operate the new Scanner, please take a few minutes to unpack...
User Manual - Page 5
INSTALLATION AND ...uneven surfaces may cause damage to the sun or excessive
heat may
cause mechanical or paper-feeding problems. y Retain the Scanner box and packing materials for shipping purposes.
2.1 Shipping Bracket The ...JAM light will turn the power off, disconnect all cables and follow the instructions below to remove the shipping bracket. 2.1.1 Removing the Shipping Bracket (refer to...
User Manual - Page 7
...side. Use a suitable screwdriver to figure 2-1 and 2-2 iv). vii). Please follow the instructions below to SCSI adapter or host. ii). Carefully place the Scanner in the use . ...factory setting for Scanner is assigned to an internal
hard disk drive, and ID 7, to refit the shipping bracket. Carefully place the Scanner back into the Scanner base. This setting assigns a specific "device...
User Manual - Page 8
SCSI ID Selector
Figure 2-3 Adjusting the SCSI ID setting.
2-4
User Manual - Page 9
Pull out the paper chute extension to about 45 degrees. Figure 2-4 Setting the ADF Paper Chute
2-5 Pull down the wire leg from under the paper chute.
iv). Raise the right side of the paper chute to the length you want. iii). Insert the wire leg into the grips on the document cover. 2.3 ADF Paper Chute (Figure 2-4) i). ii).
User Manual - Page 10
Release the paper tray gently. Insert the three protrusions on the output paper tray to the ADF. iii). Protrusions
Figure 2-5 Install the ADF Output Paper Tray
2-6 Hold the output paper rack some 30 degrees aslant as shown in Figure 2-5. iv). ii). Make sure the tray is ...
User Manual - Page 12
... the auto feeder entrance. To prevent occasional paper jam when automatically feeding multiple documents, fan the paper before loading.
ii). Adjust the left and right guides so that they are snug against the sides of the documents. Use ADF to figure 2-7. iii). Let the balance wire rest on the top of...
User Manual - Page 13
... be off .
Turning the Power On
Depress the side marked "I" to turn the power on. Host PC Term. 2.7 Connecting the Cable
i).
ii). SCSI Termination
The Fujitsu Scanpartner 15C comes complete with a built in Figure 2-8.
Connect the power cable and SCSI signal cable as shown in SCSI terminator.
The POWER LED will...
User Manual - Page 15
... paper dust. Rotate the rollers forward with your Scanner to return your finger and repeat the above cleaning procedures until the rollers are available from Fujitsu.)
?
User Manual - Page 18
....
4.1 Question and Answer
Question: The LED indicates that the Scanner is correctly installed. Question: Paper becomes jammed during scanning. Answer: a) Open the ADF unit. TROUBLESHOOTING
The Scanner will help spot major system errors in the paper guide. This will automatically perform a simple self-test each time it off and then on . When the test...
User Manual - Page 19
...your host adapter. In that is not a problem, but when scanning, the Scanner or system will not
a) You forgot to your authorized local dealer to replace the invertor.
Answer: Please check
a) If ... to change the lamp.
do the cleaning if
necessary. (See Section 3.1)
b) Use the paper guide when feeding the paper.
Question: Getting image from the TWAIN user interface for low speed PC.
...
User Manual - Page 20
... Paper Jam - Open the ADF cover to get a brighter image. Answer: Use the Brightness or Threshold setting to adjust the line art image.
4.2 Paper Jam in the ADF In the event of the original.... Pull the paper out of the Scanner as shown in Figure 4-1, arrow A.
b) Use Brightness setting from the TWAIN user interface to the full open position, arrow B. iii). Press the button at the...
User Manual - Page 22
... to change without notice. y Items other than 8.5"; y Paper with wrinkles, curls, folds or tears; y Paper with inconsistent thickness, such as cloth, metal or OHP film; SPECIFICATIONS
All specifications are subject to scan documents that cannot be properly fed by the ADF.
5-1 The following can not be fed by ADF: y Paper with clip or...
User Manual - Page 23
... Scale (256 levels) y Line Art/Halftone (64 levels) y Error Diffusion (single bit) y 300 x 600 dpi in a dpi increments y Cold Cathode fluorescent lamp y 50 pages y 15 PPM (200dpi, B/W mode, ADF) y ADF ... 80% y 10 to 40 y -10 to 50 y 570 x 350 x 165 mm(WxDxH) y Appropriate 26.5 lbs (12 kg)
5-2 5.1 Scanpartner 15C Specifications
Scanner Type
Scanning Mode
Optical Resolution Light Source ADF Capacity...
Fujitsu CG01000-464802 Reviews
We have not received any reviews for Fujitsu yet.