Manual/User Guide
Page 3
... the system frame, do not allow the system frame to touch parts (cover and base) other than parts to which the HDD is connected to Signal Ground (SG). The tightening torque must be mounted in Figure 3.2. The mounting frame is attached. Use M3 ...screw and the screw length should satisfy the specification in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is zero. 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf•cm).
... the system frame, do not allow the system frame to touch parts (cover and base) other than parts to which the HDD is connected to Signal Ground (SG). The tightening torque must be mounted in Figure 3.2. The mounting frame is attached. Use M3 ...screw and the screw length should satisfy the specification in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is zero. 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf•cm).
Manual/User Guide
Page 5
For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. Figure 3.3 Location of breather hole is shown as Figure 3.3. Locating of breather C141-E262 3-5 3.2 Mounting Because of breather hole mounted to the HDD, do not allow this to block.
For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. Figure 3.3 Location of breather hole is shown as Figure 3.3. Locating of breather C141-E262 3-5 3.2 Mounting Because of breather hole mounted to the HDD, do not allow this to block.
Manual/User Guide
Page 7
...and after installation. Ensure that the disk drive is not affected by the edges. (6) Handling cautions Please keep the following cautions, and handle the HDD under the safety environment. Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor ...contact, which may cause damage to the disk drive. C141-E262 3-7 Pressing it by external magnetic fields....
...and after installation. Ensure that the disk drive is not affected by the edges. (6) Handling cautions Please keep the following cautions, and handle the HDD under the safety environment. Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor ...contact, which may cause damage to the disk drive. C141-E262 3-7 Pressing it by external magnetic fields....
Manual/User Guide
Page 8
Installation Conditions - Figure 3.6 Handling cautions - HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening ...1200-3056-8 SKY-8A (Color Seiden Mat) SS-6500 Maker SUMITOMO 3M Achilles HIOS 3-8 C141-E262 Do not place HDD vertically to avoid falling down. Installation (1) Please use an electric driver. ESD mat Shock absorbing mat Place the shock... mat on the operation table, and place ESD mat on it. Do not drop. Do not hit HDD each other. M3 0.49N • m (5 kgf • cm). - General notes Wrist strap Use the Wrist strap. ...
Installation Conditions - Figure 3.6 Handling cautions - HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening ...1200-3056-8 SKY-8A (Color Seiden Mat) SS-6500 Maker SUMITOMO 3M Achilles HIOS 3-8 C141-E262 Do not place HDD vertically to avoid falling down. Installation (1) Please use an electric driver. ESD mat Shock absorbing mat Place the shock... mat on the operation table, and place ESD mat on it. Do not drop. Do not hit HDD each other. M3 0.49N • m (5 kgf • cm). - General notes Wrist strap Use the Wrist strap. ...