Haier HSU-24CVA03 Support and Manuals
Get Help and Manuals for this Haier item
View All Support Options Below
Free Haier HSU-24CVA03 manuals!
Problems with Haier HSU-24CVA03?
Ask a Question
Free Haier HSU-24CVA03 manuals!
Problems with Haier HSU-24CVA03?
Ask a Question
Most Recent Haier HSU-24CVA03 Questions
Not Cooling
My Haier (24cva03) Aplit Aircondition not functioning properly with remote control. It automatically...
My Haier (24cva03) Aplit Aircondition not functioning properly with remote control. It automatically...
(Posted by pappunancy 12 years ago)
Popular Haier HSU-24CVA03 Manual Pages
User Manual - Page 1
SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
HSU-18CV03(T3) HSU-24CV03(T3) HSU-24CVA03(T3)
Please read this operation manual before using the air conditioner
No.0010556977
User Manual - Page 2
...
adequate recycling. package of your
people, don't install unit by professional
Disposal of the packaging of your local waste disposal center for
the user of the safety,the air con- All electrical repairs must be disposed without any parts of an old air conditioner and instruction. Inadequate repairs may result in an air conditioner can...
User Manual - Page 4
... seriousness of possible risks and damages as follows. Do not install in the following Safety Instructions carefully prior to use .
inflammable gas leakage around the unit. Installation
WARNING
Please call Sales/Service Shop for safety use . CAUTION
Connect the earth cable. Do not install in the Do not get the unit place where there is...
User Manual - Page 6
... unit
Outlet Air filter(inside) UV light degerming device (inside)
Anion generator (inside )
Inlet grille
Vertical flap (adjust up and down air flow. Parts and Functions
Indoor unit
Display board Inlet
Air Purifying Filter (inside )
Power plug
1
1
4
1
1
4
2 3
HSU-18CV03(T3)
3
2
HSU-24CV03(T3) HSU-24CVA03(T3)
1 INLET 2 DRAIN HOSE
3 OUTLET 4 CONNECTING PIPING AND ELECTRICAL WIRING
5
User Manual - Page 7
... HEALTH button Used to select CODE A or B with heating.
6 Operation mode display
Operation mode AUTO COOL DRY
HEAT FAN
33
Remote controller
Display board
1.CODE Used to set correct time.
6. SLEEP button... use a sharp pointed article to press this button to confirm timer and clock settings.
32. TIMER ON display
12. Parts and Functions
19
18
34 11 15 23
9. ON/OFF button Used for ...
User Manual - Page 8
...case unit won't be within 7m without any display after replacing batteries in line with the "+" / "-". If the button is confirmed, press SET, "AM" or "PM" stop flashing, while clock starts...are any obstacle as illustrated. Parts and Functions
Clock Set
When unit is started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the room, the receiver...
User Manual - Page 13
... mode, the unit will not operate in COOL or HEAT mode but only in FAN mode ,AUTO is not available in FAN mode.And temp.setting is not available.
12 For each press, operation mode changes as follows:
Remote controller:
4.Unit stop
LOW MED
HI
Press ON/OFF button, the unit stops.
User Manual - Page 15
... of remote controller:
button, remote controller displays as follows :
Pos.1 Pos.2 Pos.3 Pos.4 Pos.5 Pos.6 Pos.7 Pos.8
The horizontal louvers will automatically
memorize the previous set swing position.
14
User Manual - Page 16
... 't be too high for your sleep. If it is higher than temp. In COOL,DRY mode
1 hours after sleeping. is low wind, no SLEEP function.
5.Set the wind speed change .
15 rises by 1OC further. The unit will become 2 OC lower than temp. is high or middle before which the clock...
User Manual - Page 17
... x hour x min. (TIMER ON or TIMER OFF).
5.Cancel TIMER mode Just press TIMER button several times until TIMER mode disappears. Hints: After replacing batteries or a power failure happens, time setting should be displayed on the remote controller stops flashing. Every time the button is the same as follows: Remote controller:
BLANK
TIMER...
User Manual - Page 18
...It can be adjusted within 24 hours.
4.Timer confirming for TIMER OFF
After time setting,press SET button to change TIMER mode.
According to confirm " " on the remote controller stops blinking. ...Every time the button is pressed, time setting decreases
1 min, if kept depressed, it will be displayed on LCD. 2.
" " starts ...
User Manual - Page 19
... outlet grille will run correctly, stop for a long time under the condition before the setting of health airflow function. Otherwise, the grille will close automatically. If the grille is ...outlet grills. Notice: Cannot pull direct the outlet grille by remote controller. Note: 1 .After setting the health airflow function, the position of inlet and outlet grills is fixed. 2.In heating,...
User Manual - Page 21
OFF
20 Maintenance
For Smart Use of The Air Conditioner
Setting of proper room Do not block the air inlet
temperature
or outlet
Proper temperature
Close doors and windows Use the timer effectively during operation
During ...
User Manual - Page 25
Connecting the earthing cable.
EARTHING
Do not block the air inlet or outlet. Caution
Incomplete earthing may cause troubles.Be sure to attach both right and left filters prior to the operation. Maintenance
Before Setting in Caution
After brush away dust at the plug, insert the plug of the power supply cord into...
User Manual - Page 26
... every 15 days. Multiple check
Does not work for service, check the following first. Poor cooling
Is power plug...electric plug is stopped, it should be heard.
Is temperature set correctly?
At first 2-3 minutes after unit start, this noise...immediately until 3 minutes have elapsed to protect the system. Trouble shooting
Before asking for 3 minutes to protect the air conditioner...
Haier HSU-24CVA03 Reviews
We have not received any reviews for Haier yet.