Harbor Freight Tools 62377 - 1 HP 4 in. x 6 Horizontal/Vertical Metal Cutting Band Saw Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 62377 manuals!
Problems with Harbor Freight Tools 62377?
Ask a Question
Free Harbor Freight Tools 62377 manuals!
Problems with Harbor Freight Tools 62377?
Ask a Question
Popular Harbor Freight Tools 62377 Manual Pages
User Manual - Page 1
... our technical support at: [email protected]
When unpacking, make sure that the product is intact and undamaged.
Failure to continuing improvements, actual product may differ slightly from the product described herein. Keep this product. Copyright© 2014 by Harbor Freight Tools®. Owner's Manual & Safety Instructions
Save This Manual Keep this manual or any...
User Manual - Page 3
... or other part that may result in damp or wet locations, or expose them to follow the warnings and instructions may affect ...power and overheating. Consult the owner's manual for best and safest performance. CHECK DAMAGED PARTS. Feed work area well lighted.
...to rain. Make sure switch is damaged should be properly repaired or replaced.
20. Do not wear loose clothing, gloves, neckties, ...
User Manual - Page 5
... the specific hazards in this product, but must follow OSHA guidelines.
28. WARNING: The cord of this type of injury to filter out microscopic particles. (California Health & Safety Code § 25249.5, et seq.)
32. When cutting a large workpiece, make sure the Saw Blade is properly mounted and is plugged into this instruction manual cannot...
User Manual - Page 6
...Do not smoke during use this manual. Include vibration-free periods each day of it). If any medical or physical symptoms related to ensure medical problems are not being caused or ...explained in this tool. To reduce the risk of vibration-related injury.
3. SAVE THESE INSTRUCTIONS.
Setup
Operation
Maintenance
Page 6
For technical questions, please call 1-888-866-5797. Safety
Vibration...
User Manual - Page 8
...additional information regarding the parts listed in this manual. Refer to the ...Setup
Setup -
Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of one Stand (10). Align the two mounting holes in the Wheel Bracket (130) with the two mounting holes located in the upper section of this manual...set up or use of one Stand (10), using two Bolts...
User Manual - Page 13
....
2. If the workpiece is long, support the end.
Re-tighten the Bolt. Refer to Figure N.
3. Re-tighten the Bolt.
Page 13 Safety
Setup
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section ... Raise the Body Frame (93) to its electrical outlet before set up or use of this manual including all text under subheadings therein before performing any procedure in ...
User Manual - Page 15
... two Bolts (13) to Figure S.
Set Screw (96)
Saw Blade (66)
Upper Blade Wheel (83)
Figure S
7. When adjustment is necessary, the Blade Guide Bearings should not rub against the flange....setting. Raise the Body Frame to its full vertical position.
To avoid injury, keep hands clear of the Upper Blade Wheel flange. Safety
Setup
To Adjust the Blade Tracking
1. Turn the Support...
User Manual - Page 16
...Saw Blade.
Turn the Support Plate (127) to the right until it . To Adjust the Feed Rate
Adjust the feed rate of the Body Frame by loosening the Blade Guide Adjusting Knob (68) ...questions, please call 1-888-866-5797. The Blade Guide Brackets should be used for the Blade Wheels (63, 83) to increase tension on page 11.
2.
Safety
Setup
To Adjust the Blade Tension
1. NOTICE: Do ...
User Manual - Page 18
... previously discussed in this manual) have been made, plug the Power Cord (27) into the nearest 120 volt, grounded, electrical outlet.
5. WARNING! Never attempt to reach full speed before using.
Refer to Figure V. Operation
Maintenance
Figure V
4. Once all times. Locking Pin (126)
Item 62377 Safety
Setup
General Operating Instructions
Vertical Position
WARNING! Always...
User Manual - Page 19
... Frame
Switch Push-Off Tip
Vise Assembly
Blade
Setup
Operation
Power Switch
Stock Stop
Support Plate
Figure X
Locking Pin
6. Once all ...Page 19
Maintenance Turn off the Band Saw and correct any problems before feeding the Saw Blade into the nearest 120 volt, ...workpiece. Turn the Support Plate clockwise until the Saw Blade comes to lock Body Frame in this manual) have been made ...
User Manual - Page 20
... have the problem corrected before...
Setup
Maintenance and Servicing
Procedures not specifically ...manual must be performed by turning the Blade Tension Adjusting Knob (91).
4. To clean the exterior parts of the machine in this power tool is not in use . Do not immerse any liquids.
4. Replacing the Saw Blade
5. All maintenance, service, or repairs not mentioned in any electrical part...
User Manual - Page 23
.... 7. Safety
Setup
Troubleshooting
Problem
Possible Causes
Likely Solutions
Tool will not start. 1. Check that Worm is unpowered, turn off tool and allow to work at its length and load. If outlet is in .
2. Tool operates slowly.
4. Excessive noise or rattling. Saw Blade dull or damaged. 2. Forcing machine to cool. Have technician service tool.
1. Replace Saw...
User Manual - Page 24
... workpiece material.
2.
Check manual for the workpiece material.
1. See page 10. 3. Adjust Vise so it is not square with Blade. See page 16. 3. See page 15.
1. See page 16. 3. Gradually adjust Saw Blade tension until optimal
tension has been achieved. Replace Blade Guides. Adjust Blade Guide Bearings. Disconnect power supply before service. Unusual wear on...
User Manual - Page 25
...HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. Page 25 Parts List
Part
Description
1 Foot Pad
2 Stand Support
3 Flat...
User Manual - Page 26
...1 1 1 1 1 1 2 1 2 2 1 3 1 1 2 1 1 1 1 1
Setup
Operation
Maintenance
Record Product's Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Page 26
For technical questions, please call 1-888-866-5797.
Item 62377 Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.
Harbor Freight Tools 62377 Reviews
We have not received any reviews for Harbor Freight Tools yet.