Harbor Freight Tools 63024 - 900 Peak/700 Running Watts Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 63024 manuals!
Problems with Harbor Freight Tools 63024?
Ask a Question
Free Harbor Freight Tools 63024 manuals!
Problems with Harbor Freight Tools 63024?
Ask a Question
Popular Harbor Freight Tools 63024 Manual Pages
User Manual - Page 1
... Tools required for assembly and service may differ slightly from the ...manual may not be drawn proportionally. Owner's Manual & Safety Instructions
Save This Manual Keep this manual or any artwork contained herein may be reproduced in any parts...MANUAL. Visit our website at: http://www.harborfreight.com Email our technical support at:
[email protected] Email our Engine support...
User Manual - Page 2
Page 2
For technical questions, please call 1-888-866-5797.
Table of Contents
Specifications 2 Safety 3 Setup 7 Operationr 8
Maintenances 11 Troubleshooting 14 Parts Lists and Diagrams 16 Warranties
Specifications
Generator
Displacement Engine Type Cooling System
Output Receptacles
Fuel
Type
Capacity
Type Oil
Ratio
Run Time @ 50% Load with gasoline) 50:1 gasoline-to ...
User Manual - Page 3
... and situations that may result in minor or moderate injury.
Read the manual before set-up and/or use.
Symbol Definitions
Symbol
Property or Statement
RPM Revolutions ... Safety
Setup
WARNING SYMBOLS AND DEFINITIONS This is used to alert you to personal injury. Indicates a hazardous situation which cannot be built into this manual cannot cover all instructions. Wear...
User Manual - Page 4
...codes.
7. Use only lubricants and fuel recommended in the Specifications...must be installed by a qualified electrician.
Safety
Setup
Set up and...codes and standards before operation. Read and adhere to the generator: Make sure that can create a potential for standby power to backfeed into the utility lines. Before connecting an appliance or power cord to the instruction manual...
User Manual - Page 5
...these instructions ...for your model. Only use...Code § 25249.5, et seq.)
36. Stay clear of the generator. Do not reach over or across equipment while operating.
38. Safety
Setup
Operating Precautions (cont.)
12. Do not exceed the maximum power rating of hot parts...serviced before leaving the work to be suitable for one piece of the Generator.
13. Do not touch electrically energized parts...
User Manual - Page 6
...manual or any part of ignition around the equipment, especially when refuelling. 2. Replace... little room for a replacement.
7. SAVE THESE INSTRUCTIONS. Replace any spilled fuel and ...repair person using only identical replacement parts.
Have the equipment serviced by the manufacturer or distributor. Refuel in the air. Follow scheduled engine and
equipment maintenance. Setup...
User Manual - Page 7
....
The grounding rod must be required. Safety
Setup
Set Up
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all relevant electrical codes and standards before set up or use of this equipment may be properly grounded in accordance with proper spark arrestor installed. Operation of the unit to fire prevention...
User Manual - Page 8
...Setup
Operation
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this product.
Note: Do not use gasoline that has been treated with 1 gallon of this manual...Strainer and remove any problems are found, do not...parts before adding fuel.
Add fuel stabilizer to cool before set up or use . Then replace the Fuel Cap.
7.
c. ITEM 63024 Then replace...
User Manual - Page 10
...amperage rating.
• Refer to appliance/tool owner's manuals to completely run at a minimum. Check nameplate wattages...equipment and engine operation.
Turn the Engine Switch off .
Safety
Setup
Break-in the Maintenance section. b. Allow the Engine to Generator... . Keep cord length at no load for complete storage instructions.
Once the load is wattage.
• Never exceed ...
User Manual - Page 11
....
Follow all service instructions in a well-ventilated area away from
combustion chamber Replace fuel line if necessary
Before Each Use
Monthly or every 20 hr. Check/adjust idle speed 2. TO PREVENT SERIOUS INJURY FROM FIRE: Fill the fuel tank in this manual, will differ depending on factors such as a general guide.
Safety
Setup
Maintenance
WARNING
TO...
User Manual - Page 14
... damaged by the carburetor needle sticking.
9. Gently tap side of oil into spark plug hole. Replace Fuel Filter. Connect spark plug cap properly.
2. Correct spark plug gap.
4.
Safety
Setup
Troubleshooting
Problem
Possible Causes
Engine will not start handle several times to RUN position. Carburetor not primed. 6. This can be caused by ethanol. Spark plug...
User Manual - Page 15
...fresh 87+ octane stabilizer-treated unleaded gasoline/oil mixture. Safety
Setup
Problem
Engine misfires
Possible Causes
1.
Replace spark plug cap.
4. Allow engine to warm up prior...treated unleaded gasoline/oil mixture. Have product repaired.
1. Engine too cold.
3. Test/replace fuel tank cap.
3. Have qualified technician diagnose and service engine.
1. doesn't have power
2....
User Manual - Page 16
...replacement parts. ITEM 63024
Safety
Setup
Parts Lists and Diagrams
Parts List
Part
Description
1 Bolt 6 x 16
2 Filter Covering
3 Filter Block
4 Bolt Rivet 6 x 20
5 Flat Washer
6 Steel Set... 1 2 1 1 1 1 1 1 1 1 1 1 1 1 3 1 4 1 1 1 1 1 2 1 1 1 2
Part
Description
45 Shelf
46 Bent Axle
47 Bearing 6004
48 Left Tank
49 Flange Bolt 6 x 45
50 Flange Bolt 6 x 55
51 Big Oil ...
User Manual - Page 18
...part has failed due to abuse (including failure to exceed 30 days. or (b) bring the to you should contact HFT product support at no event be completed in a reasonable amount of purchase.
This warranty gives you specific...include parts such as the problem exists in this product is defective, the part will repair or replace, at our option, your Owner's Manual.
Safety
Setup
...
User Manual - Page 19
... is delivered to the first scheduled replacement, the part will be repaired or replaced by contacting HFT product support at 1-888-866-5797 or [email protected].
6.
Any such part repaired or replaced under warranty of a non-exempted add-on or modified part. Notwithstanding the provisions herein, warranty services or repairs will be provided at all applicable regulations...
Harbor Freight Tools 63024 Reviews
We have not received any reviews for Harbor Freight Tools yet.