Hayward LPCUS11150 Support and Manuals
Get Help and Manuals for this Hayward item
View All Support Options Below
Free Hayward LPCUS11150 manuals!
Problems with Hayward LPCUS11150?
Ask a Question
Free Hayward LPCUS11150 manuals!
Problems with Hayward LPCUS11150?
Ask a Question
Popular Hayward LPCUS11150 Manual Pages
ColorLogic-CrystaLogic-Installation-Operation-Manual-092467RevG - Page 2
... PROPERTY OWNER
2
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Read and follow all instructions.
Light has no more than 72 in death or serious injury to the cord are only made in this manual have been read and fol-
and no user serviceable parts inside.
Disconnect electrical power before installing or servicing this equipment. This product to keep any...
ColorLogic-CrystaLogic-Installation-Operation-Manual-092467RevG - Page 11
.... An LKBUN1000 is designed to install into the Hayward LTBUY11300 300 Watt and Hayward Junction Box transformers.
Replacement Parts
ITEM 1 2 3 4 5
Pool Light Parts
PART NUMBER
LN(x)UY1000 SPX0800Z1 SPX0800RW SPX0800LPAK2 LPXADAPT1
DESCRIPTION
QTY
Pool Trim Rings
1
Metal Light Screw Kit
1
Spacer Washer for mounting and wiring instructions. For Network Control Only: Hayward...
ColorLogic-CrystaLogic-Installation-Operation-Manual-092467RevG - Page 12
...OmniLogic or OmniHub pool controller only. ColorLogic 2.5 & earlier mode: Use this mode when installing your new light in Networked mode or Omni Direct mode. Refer to the next mode.... to change modes, turn off for more information. The light will then advance to the controller's manual for between 11-15 seconds. 2.
To change modes, turn off for at the desired mode. ...
ColorLogic-CrystaLogic-Installation-Operation-Manual-092467RevG - Page 13
... or OmniHub pool control to the OmniLogic or OmniHub manuals for over 60 seconds, and is controlled through power...to white for 15 seconds for programs and operation instructions.
13 UUSSEE OONNLLYY HHAAYYWWAARRDD GGEENNUUIINNEE RREEPPLLAACCEEMMEENNTT PPAARRTTSS Programs
... programs which requires no special controller or interface. Once installed, all display the same colors and shows at the ...
ColorLogic-CrystaLogic-Installation-Operation-Manual-092467RevG - Page 14
... these instructions to a cooler color (Deep Blue Sea, Royal Blue, etc.) until air/water temperatures cool off. Follow the steps in the proper mode (page 12). SOLUTION: Install a Hayward GLX-HAL-XSNUB snubber capacitor across the primary leads (line to neutral) of the light
switch or relay.
14 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS PROBLEM...
Replacing 120V Pool Spa Light With UCL Light Instructions - Page 1
...service panel! Remove the light from moving freely through conduit You have duct tape for more information) Light fixture housing (Niche) has been installed per the National Electrical Code...code requirements and wiring methods
Installation Preparation Read the entire Universal ColorLogic/CrystaLogic manual Read this Guide... is no junction box in manual) If replacing a SwimQuip® light, ...
Replacing 120V Pool Spa Light With UCL Light Instructions - Page 2
... RevB
READ SAFETY INSTRUCTIONS AND COMPLETE SAFETY CHECKLIST INSIDE FRONT COVER OF MANUAL
Hayward (R) is a registered trademark ColorLogic (TM) and CrystaLogic (TM) is in the light being inadequately fastened. Some niches may result in place. Replacing 120 volt pool or spa lights with Universal ColorLogicTM or CrystaLogicTM
STEP 6a: Install Light to most Niches...
Universal ColorLogic and CrystaLogic Installers/Inspectors Sheet - Page 1
...07207
www.hayward.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
POOL WATER BONDING NEC PROVISIONS: For Pool...FORMING SHELL) ALREADY INSTALLED IN THE FIELD. For assistance with unbreakable lens and no serviceable parts. UNBONDED LIGHTING NEC...INSTALLED PER THE NATIONAL ELECTRICAL CODE. For all other product installation or usage assistance, contact Hayward Technical Support at 888-898-9674.
Replacing 12V Pool Spa Light With UCL Light Instructions - Page 1
... as shown below. Replacing 12 volt pool or spa lights with the new light (refer to compatibility table in manual) If replacing a SwimQuip® ...Guide if your light is wired to pull freely through the conduit.
Firmly pull on electrical wiring and understand electric code requirements and wiring methods
Installation Preparation Read the entire Universal ColorLogic/CrystaLogic manual...
Replacing 12V Pool Spa Light With UCL Light Instructions - Page 2
... and make the wiring connection at the light end for placing the light on the deck if pool servicing ever requires light removal. READ SAFETY INSTRUCTIONS AND COMPLETE SAFETY CHECKLIST INSIDE FRONT COVER OF MANUAL
Hayward (R) is a registered trademark ColorLogic (TM) and CrystaLogic (TM) is not in the niche.
Plastic gunite type niches...
Universal ColorLogic and CrystaLogic Troubleshooting Guide - Page 8
... following sequence should be conducted manually by entering and toggling relays in the lower right hand corner. Step 1
Step 2
Tap on the right side of water the lights are associated with (all bodies if applicable). How To: Resync Lights -
Step 4
Locate and tap the resync icon, in service mode. Step 3
Select the...
Universal ColorLogic and CrystaLogic Troubleshooting Guide - Page 24
... 2 minutes)
Problem solved
Does this issue YES
still exist? NO
Check the
YES primary side of
the transformer for 120VAC, is
voltage correct? 3. NO
Check all connections, if correct contact tech support (908)355.7995
NO
There is a break in the line, bad connection, OR a voltage drop
issue
Check connections and
replace the...
Universal ColorLogic and CrystaLogic Troubleshooting Guide - Page 25
The LED(s) will flash if not enough power is a problem with a connection, or a potential problem with the light. After restoring power and cycling, IF lights are still dim/flashing, go to step 3B.
IF correct, check connections and call tech support (908) 355.7995.
25
IF no/low voltage, go to step 3C. Verify...
Universal ColorLogic and CrystaLogic Troubleshooting Guide - Page 35
...
Check the junction box, for at least 2 minutes)
Problem solved
Does this issue YES
still exist? NO
Check all connections, if correct contact tech support (908)355.7995 NO
There is a break in the... line, bad connection, OR a voltage drop
issue
Check connections and
replace the transformer if
necessary
Correct ...
Universal ColorLogic and CrystaLogic Troubleshooting Guide - Page 36
The LED(s) will flash if not enough power is a problem with a connection, or a potential problem with the light.
IF correct, check connections and call tech support (908) 355.7995.
36 Network: Light(s) Flashing/Dim
Lights generally become dim or flash when a voltage drop is affecting light power, there is being supplied. ...
Hayward LPCUS11150 Reviews
We have not received any reviews for Hayward yet.