Hayward RC9742WCCUBY Support and Manuals
Get Help and Manuals for this Hayward item
This item is in your list!
View All Support Options Below
Free Hayward RC9742WCCUBY manuals!
Problems with Hayward RC9742WCCUBY?
Ask a Question
Free Hayward RC9742WCCUBY manuals!
Problems with Hayward RC9742WCCUBY?
Ask a Question
Popular Hayward RC9742WCCUBY Manual Pages
Robotic Cleaners Troubleshooting Guide - Page 2
... & TigerShark QC Important safety instructions Service Tools Filter Removal/Cleaning and Drain Flaps Handle Removal Venturi Removal Bottom Lid Disassembly Side Cover Removal Drive Track and Idlers Power Cord and Motor Box Wheel Tube Brush and Bearings Using the Scanner Tool Power Supply and Flotation Cord Testing Basic Operation Troubleshooting
Page 1 Page 2 Pages...
Robotic Cleaners Troubleshooting Guide - Page 3
Table of Contents Continued
SharkVAC & E-Vac Service Tools Power Supply Filter Removal Filter Replacement Wheel and Tire Removal Side Cover Removal Drive Track and Idlers Main Drive Pulley Removal Wheel Tube Removal Wheel Tube Brush Power Cord Removal Motor Box Removal Power Supply and Flotation Cord Testing Troubleshooting
Page 44 Page 45 Pages 46...
Robotic Cleaners Troubleshooting Guide - Page 5
Service Tools
Pin Removal Tool
Torque Driver
Torx Bit Spanner Tool
Torx Driver
Scanner
Page 2
Robotic Cleaners Troubleshooting Guide - Page 6
Lighted
Quick Clean LED (QC Models Only)
Power Cord
Full Cycle Button and LED
(QC Models Only)
Flotation Power Cord Connector
Page 3 Power Supply
On/Off Switch -
Robotic Cleaners Troubleshooting Guide - Page 9
Page 6 Be careful not to use
in heavy spring cleaning. Filter elements removed
Spring cleanup filter elements. Filter Removal
Note: Elements must be installed with support ribs facing outward
Filter cartridge assembly
Note: Elements can be cleaned by gently spraying with a garden hose. For temporary use high
pressure or this may damage the element.
Robotic Cleaners Troubleshooting Guide - Page 30
It does not contain oil and is a sealed unit and cannot be replaced.
Motor assembly removed. Impeller removal
Page 27 Note: The motor assembly is water cooled. The impeller
can be serviced, only replaced.
Power Cord & Motor Box Removal
Output shaft key on motor, mates with drive gear.
Robotic Cleaners Troubleshooting Guide - Page 32
Page 29
Wheel Tube Brush
Brush replacement can be done leaving the machine assembled or broken down. Unsnap the tabs, these
run length wise of the brush.
Robotic Cleaners Troubleshooting Guide - Page 34
Using The Scanner Tool
Power switch on
Scanner female end
Initializing Please wait
Startup Screen
Scanner male end
Scanner Setup
Power cord to cleaner
Page 31
Robotic Cleaners Troubleshooting Guide - Page 36
... the water/pool. 2.
Remove impeller and
inspect for hair or grass around the pump impeller. Unit will stop after placing the unit in manufacture or repair. 4.
Robotic Cleaners Troubleshooting Guide - Page 38
... power supply and and the PCB (printed circuit board) in pin terminal 1 and 2 and turn on power supply
21 to .8 ohm's is not repairable and must be replaced if defective.
Page 35 The power
supply is acceptable. Insert voltage probes in the motor assembly box.
Testing Power Supply & Flotation Cord
CheCcokmPmowuneircantidon ConFnaeilcutrioe...
Robotic Cleaners Troubleshooting Guide - Page 41
... use of TigerShark for pool maintenance as often as required.
• Increase frequency of the TigerShark for pool maintenance. Service and inspect the pool filter system, vacuum the pool and resume use .
Troubleshooting
Will not climb walls
Filter Too Dirty to Allow Proper Machine Performance
• Pool condition is in the...
Robotic Cleaners Troubleshooting Guide - Page 42
... foam rollers only if a dirty pool condition is ruled out. • Clean vinyl or tile pool surface is too slick. Machine problem
• Broken impeller. Replace the motor box assembly. Troubleshooting
Will not climb walls
Pool design or configuration • The pool bottom corner design may allow objects to pass through and...
Robotic Cleaners Troubleshooting Guide - Page 43
Install the Restrictor Plate Kit RCX11206 in the venturi.
• Inspect bottom lid filter plate gasket and replace if torn or missing. • Set handle position at Waterline, Blows Air Bubbles Through the Exit Venturi
• Above average traction in the
center or straight position. • Check water chemical balance. Page 40 Troubleshooting
Will...
Robotic Cleaners Troubleshooting Guide - Page 47
Pin Removal Tool
Torx Bit T-20
(not supplied)
Spanner Tool
Service Tools
Power Driver (not supplied)
Torx Drivers T-10 & T-25 (not supplied)
Belt Installation Tool
Torque Driver
Page 44
Robotic Cleaners Troubleshooting Guide - Page 65
Output shaft key on motor, mates with drive gear.
The impeller
can be serviced, only replaced. Note: The motor assembly is water cooled. Motor Box Removal
Rotate motor slightly to remove drive output shaft from side of unit, then lift out motor assembly.
Impeller removal
Page 62 It does not contain oil and is a sealed unit and cannot be replaced.
Hayward RC9742WCCUBY Reviews
Do you have an experience with the Hayward RC9742WCCUBY that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Hayward yet.
Earn 750 points for your review!