Hitachi 937984Z - Wheel Guard For G23MR Support and Manuals
Get Help and Manuals for this Hitachi item
This item is in your list!
View All Support Options Below
Free Hitachi 937984Z manuals!
Problems with Hitachi 937984Z?
Ask a Question
Free Hitachi 937984Z manuals!
Problems with Hitachi 937984Z?
Ask a Question
Popular Hitachi 937984Z Manual Pages
Instruction Manual - Page 3
... use this power tool. MEANINGS OF SIGNAL WORDS
WARNING indicates a potentially hazardous situations which , if not avoided, may result in this Instruction Manual. Basic safety precautions are outlined in the "SAFETY" section of the safety precautions, warnings and operating instructions in death or serious injury.
Most accidents that has not been specifically recommended by observing...
Instruction Manual - Page 4
... area safety a) Keep work area clean and well lit. b) Avoid body contact with earthed (grounded) power tools. Keep cord away from heat, oil, sharp edges or moving parts. English
SAFETY
GENERAL SAFETY RULES
WARNING: Read all instructions
Failure to follow all of the warnings listed below may result in serious personal injury.
4 c) Do not...
Instruction Manual - Page 5
...devices can be repaired. f) Dress properly. Keep your power tool serviced by poorly maintained power tools. Use the correct power tool for appropriate conditions will ensure that have the power tool repaired before plugging in power tools that the safety of starting . c) Disconnect the plug from the power source and/or the battery pack from moving parts. If damaged, have...
Instruction Manual - Page 6
... -for applications other body parts near the tool's moving parts. Contact with a rated capacity which is GREATER than those specified. NEVER use proper guard with grinding wheel. Accessories must be sure to high intensity noise can fly apart and cause injury.
3. ALWAYS use a power tool for example- If maintenance or servicing requires the removal of a guard...
Instruction Manual - Page 7
... is running unattended. Blades and accessories must be used until it immediately and arrange for dust build-up frequently.
15. Check for repairs by a Hitachi authorized service center.
17. Operate the power tool at a higher voltage than the rated voltage, it may be dropped or struck against hard materials inadvertently, it will result in abnormally...
Instruction Manual - Page 8
...Either the symbol " " or the words "Double insulation" appear on the power tool or on page 12). 27. Touching these precautions: ⅜ Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this
power tool, and only genuine HITACHI replacement parts should be careful with this Instruction Manual, including not using " on the nameplate. Definitions for symbols used to...
Instruction Manual - Page 9
English
SAVE THESE INSTRUCTIONS AND
MAKE THEM AVAILABLE TO OTHER USERS AND OWNERS
OF THIS TOOL!
9
Instruction Manual - Page 10
... power tool. Weight
Wheel guard Fig. 1
G18SR
G23SR
Single-Phase Series Commutator Motor
Single-Phase 120 V AC 60 Hz / DC
15 A
6,000/min
7" (180 mm) 7/8" (22 mm)
9" (230 mm) 7/8" (22 mm)
9.5 lbs (4.3 kg)
10
NAME OF PARTS
Push button Gear cover
Housing
Handle
Packing gland
Switch Brush cap
Side handle
Depressed center wheel
SPECIFICATIONS
Model...
Instruction Manual - Page 11
...resulting in the ON position, the power tool will start operating immediately and can cause serious injury.
3.
If such a fautly receptacle is connected to make appropriate repairs. Contact a licensed electrician to a... or unauthorized personnel.
11
Power switch Ensure that the power source to be replaced or repaired.
4. WARNING: Damaged cord must be kept as short as practicable....
Instruction Manual - Page 12
...wheels rated at an angle that the push button is replaced 3 minutes or more
When starting daily work , test... protect the operator's body from
injury by a broken wheel piece.
[Installing and adjusting the wheel guard]
⅜ Slightly loosen the screw on...center wheel is disengaged by first clearing the area
of this manual for operation,
and make sure the grinder runs smoothly and
...
Instruction Manual - Page 14
... dust or dirt until it has come to assemble or disassemble the depressed center wheel,
unless the power switch is facing upward.
(2) Align the oval-shaped indentation of the wheel washer with the notched part of the
spindle, then attach them.
(3) Fit the protuberance of the depressed center wheel onto the wheel...
Instruction Manual - Page 15
...they are consumable parts.
CAUTION: Using ...trouble. of the screws be loosened, retighten them immediately. of the wear limit will stop carbon brush is worn in excess of carbon brush
44
74
NOTE: Use HITACHI carbon brush No. 44 or 74 indicated in the figure. Confirm that time, replace... switch power OFF and disconnect the plug from the receptacle
during maintenance and inspection.
Instruction Manual - Page 16
...-head screwdriver. B: Code No. This Parts List will be observed. C: No. MODIFICATIONS: Hitachi Power Tools are constantly being improved and modified to the Hitachi Authorized Service Center when requesting repair or other maintenance. To assure that only authorized replacement parts will eventually require servicing or replacement of parts because of power tools, the safety...
Instruction Manual - Page 17
... (230 mm) external dia. × 1/4" (6 mm) thickness × 7/8" (22 mm) hole dia. (Code No. 701090)
NOTE: Specifications are subject to change without any obligation on the part of the HITACHI. STANDARD ACCESSORIES
⅜ Wrench (Code No. 937913Z 1 ⅜ Side Handle (Code No. 322411 1
OPTIONAL ACCESSORIES ..... sold separately
⅜ Depressed center wheel (10pcs.
The use of...
Hitachi 937984Z Reviews
Do you have an experience with the Hitachi 937984Z that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Hitachi yet.
Earn 750 points for your review!