Homelite UT43160 Support and Manuals
Get Help and Manuals for this Homelite item
View All Support Options Below
Free Homelite UT43160 manuals!
Problems with Homelite UT43160?
Ask a Question
Free Homelite UT43160 manuals!
Problems with Homelite UT43160?
Ask a Question
Most Recent Homelite UT43160 Questions
How To Replace Trigger On Homelite Pole Chain Saw
How to replace trigger in handle on homelite pole chainsaw?
How to replace trigger in handle on homelite pole chainsaw?
(Posted by ruthdavis550 9 years ago)
Homelite UT43160 Videos
Homelite Pole Saw (UT43160)
Duration: :21
Total Views: 11,652
Duration: :21
Total Views: 11,652
Popular Homelite UT43160 Manual Pages
User Manual - Page 4
Replace damaged cords immediately. Damaged cords increase the risk of electric shock.
Make sure your product will draw. The smaller the gauge number, the heavier the cord. Contact at an angle over 60° from one heavy enough to accidents.
Use pole saw chain and be driven rapidly back toward you or pull you...
User Manual - Page 6
...personal injury hazard.
Wet Conditions Alert
Do not expose to observe safe practices can result in electric shock.
away. DANGER! Failure to use in dry conditions and to rain or use ...duty protective gloves when handling the pole saw and the blade. Read the Operator's Manual
Wear Eye and Head Protection
To reduce the risk of Electrocution
Electric Shock
No Hands Symbol
Volts Amperes...
User Manual - Page 7
..., if not avoided, may result in the operator's manual, do not use only identical replacement parts. WARNING:
To avoid serious personal injury, do not ...INSTRUCTIONS
Page 7 - English SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with head protection. When servicing, use this product.
Call Homelite customer service for repair...
User Manual - Page 10
... are replaced. WARNING:
Do not attempt to power supply until the parts are ...parts are attempting. PACKING LIST
Pole Saw Scabbard Operator's Manual
WARNING:
Do not use . WARNING:
If any parts on this product until assembly is misuse and could result in accidental starting , the lock-out button must be adjusted to the product by the manufacturer and require customer installation...
User Manual - Page 14
...cutting procedures will result in the bar and chain binding and becoming pinched or trapped in ...pole saw . away. This should happen:
n Stop the motor and disconnect from the ground, lift the limb while holding the saw shaft to position the unit at least 50 ft. n Plan the cut . Do not stand directly under the branch being cut carefully. n Work slowly, keeping both hands on the specific...
User Manual - Page 15
... instruction manual maintenance instructions, should be damaged by competent chain saw chain is no slack on the drive links hang out of any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in fig. 11. Make sure the guide bar nut is running.
APPROX .050 in serious personal injury or property damage. Refer to Replacing...
User Manual - Page 17
... decreasing the chain's cutting ability. n Check and refill the bar lube reservoir every time the pole saw is formulated to perform over a wide temperature range with no dilution required.
BAR NUT
REMOVE CAP
RAKER (DEPTH GAUGE) CLEARANCE
Fig. 16
BAR LUBE RESERVOIR
Fig. 17
.025 in.
n Depth gauge (or raker clearance) setting determines the...
User Manual - Page 19
.... Store idle unit indoors in this manual. This is inaccessible to ensure your name, mailing address, phone numbers, email address, Homelite product(s) purchased with this manual.
TROUBLESHOOTING
PROBLEM
CAUSE
REMEDY
Bar and chain running hot and smoking.
Inspect guide bar and chain for each product. Mail the card to www.homelite.com and register your product, call...
User Manual - Page 20
... and Straps, Guide Bars, Saw Chains
Homelite reserves the right to change or improve the design of warranty shall be defective in this operator's manual. ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE STATED WARRANTY PERIOD. HOMELITE'S OBLIGATION UNDER THIS WARRANTY IS STRICTLY AND EXCLUSIVELY LIMITED TO THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS AND HOMELITE DOES NOT ASSUME...
User Manual 2 - Page 1
UT43160
ALL VERSIONS REPAIR SHEET HOMELITE ELECTRIC POLE SAW MODEL NO.
User Manual 2 - Page 2
... the motor housing. SEE NOTE
SECTION "A"
5
1 34
2
9
6
8
7
KEY PART
PARTS LIST
NO. Always mention the model number in all correspondence regarding your nearest Homelite authorized service dealer.
2 To avoid the possibility of the Double Insulated System. ALL VERSIONS
The model number will be performed by your ELECTRIC POLE SAW or when ordering replacement parts. HOMELITE...
User Manual 2 - Page 3
...
28
29 30
25
3 2
15
9 22
10
22 8
54
17
29 30
26
27 13
23 18
16
12
11
20
Section "A" represents an important part of the double insulated system of this tool requires dielectric testing to insure customer safety and to this tool. SECTION "A"
HOMELITE ELECTRIC POLE SAW -
User Manual 2 - Page 4
HOMELITE ELECTRIC POLE SAW - PART NUMBER
DESCRIPTION
QTY
31305163G Power Cord 1 31309152G Pole Assembly (Incl. Key Nos. 25-26 1 31302152G Handle Assembly 1 3410801G Cord Clamp 3 3220905G Screw (M4 x 12 mm 6 33402161G Compression Spring 2 34110152G Lock-off Button 1 32907152G Lock Nut (M6 2 34204152G Rubber Pad 2 31311152G Motor Assembly 1 31314152G Oil Tank ...
User Manual 2 - Page 5
ALL VERSIONS
BLACK WHITE
WIRE NUT WHITE
SWITCH
BLACK
WHITE BLACK
WIRING DIAGRAM
5 MODEL NUMBER UT43160 - HOMELITE ELECTRIC POLE SAW -
Replacement Parts List - Page 2
...NO.
1 2 3 4 5 6 7 8 9
part NUMBER 901289001 3290875G 33302102G 33902102G 31306152G 32901152G 31308152G 310605001 31307152G 987000228
PARTS LIST
DESCRIPTION
QTY
Chain...1
Retaining Ring...1
Washer...1
Sprocket...1
Oil Cap...1
Hex Nut (M6)...1
Chain Cover Assembly 1
Bar...1
Chain Adjustment Assembly 1
Operator's Manual...1
2 homelite electric Pole saw Model No...
Homelite UT43160 Reviews
We have not received any reviews for Homelite yet.