Humax DT9500CI Support and Manuals
Get Help and Manuals for this Humax item
View All Support Options Below
Free Humax DT9500CI manuals!
Problems with Humax DT9500CI?
Ask a Question
Free Humax DT9500CI manuals!
Problems with Humax DT9500CI?
Ask a Question
Popular Humax DT9500CI Manual Pages
User Manual - Page 2
... to change without HUMAX's prior consent in writing except approval of ownership of copyright and copyright law.
**
The information in this user manual next to safely install, use and maintain the product at maximum performance.
Throughout the whole manual, Note indicates additional product operation information to make the user aware of possible problems and information...
User Manual - Page 3
... filled with any maintenance or installation procedures. • Do not...satellite dish. • Place the product indoors to avoid exposing it can touch dangerous voltage points or damage parts. • When replacement parts...instructions for long periods of the product. • Do not use any unsupported attachments as the original part... the service technician uses replacement parts specified...
User Manual - Page 4
... GB19 3.5 Teletext GB20
4. Installation GB23 5.1 DIGITURK GB23 5.2 Advanced Installation GB24 5.3 Organise Channels GB29 5.4 Factory Settings GB32
6. System Settings GB33 6.1 Language Setting GB33 6.2 Time and Date Setting GB33 6.3 A/V Output Setting GB34 6.4 UHF Tuning GB34 6.5 Other Setting GB35 6.6 System Information GB36
GB 3 Contents
1. Setup ...GB12 2.1 Connecting Antenna...
User Manual - Page 8
...
**
Outputs digital audio signals (S/PDIF).
**
GB 7 AUDIO L/R
**
Connects to the TV or VCR and outputs video signals.
7. The default UHF channel is 36.
**
9. RS-232C
**
Connects to your PC to a satellite antenna cable.
**
2. RF OUT
**
Connects the RF output jack of the product with the RF cable. LNB IN
**
Connects to update software.
**
4. RF...
User Manual - Page 13
Select the most appropriate procedure depending on your local product distributor.
2.1 Connecting Antenna/TV/VCR
1. Connect the antenna to any problem when setting up the product.
Setup
2. Before you must disconnect all equipments from their power sources. The SCART cable is connected as in the figure above. GB 12 Note: If you ...
User Manual - Page 15
GB 14 2. Setup
3. The RF cable is connected as in the figure above.
**
Note: The default UHF channel is 36. Using RF Cable **
** 1. Connect the antenna to the LNB IN of the product. 2.
User Manual - Page 25
... SMATV.
• Satellite Name: Displays the satellite list in name order. Enter the PIN code using motorised system, select "Enabled".
GB 24 Antenna Alternative 16 is set to antenna or LNB. • Motorised System: When using the NUMERIC buttons. You can select "On" or "Off".
**
When you are using DiSEqC (Digital Satellite Equipment
Control) switch to...
User Manual - Page 26
...Manual Search
You can delete the channels using the transponder information.
**
• Antenna Alternative: Select antenna alternative which has different
combinations of settings for search. Otherwise, select "No".
• Advanced: In advanced mode, enter Video Packet ID (PID), Audio PID,
and PCR PID.
**
After setting the parameters of the selected satellite... (Forward Error Correction)....
User Manual - Page 27
... Reset
Search / Go to ", "Store" or "Reset".
**
- In installer mode, this is selected.
**
• Satellite Name: Select a satellite to the saved position of the selected satellite. - Store: Saves the current position of the satellite manually.
• Motor Control: You can select one option among "Search", "Go to / Store Satellite Setting
This menu appears only when you enable Motorised...
User Manual - Page 28
...; Store West Limit: You can set the maximum for each satellite manually, select the Satellite Name, set DiSEqC Command Mode to "Installer", and then set Motor Control to the position of the selected satellite.
**
4. To move the motor to the pre-set position of the satellite, select the desired Satellite Name, set DiSEqC Command Mode to "User", set Motor Control to "Goto", and...
User Manual - Page 29
... To enter Automatic Search menu, press the OPTS button, then select Installation-Advanced Installation-Automatic Search.
**
• Antenna Alternative: Select antenna alternative which has different combinations of settings for SMATV.
**
• Automatic Skip: When skipping all field of tuner (950~2150MHz), select "Manual". Otherwise, select "Auto" to search channels through all scrambled...
User Manual - Page 33
... more information, refer to the factory settings using the Factory Settings menu (MENU-Installation-Factory Settings).
5. GB 32 Warning: Please note that once you perform the factory setting, all data
except the customised PIN code will be restored to enter the PIN code. You will be prompted to the factory settings. Installation
5.4 Factory Settings
You can restore the product to...
User Manual - Page 36
6.5 Other Setting
You can adjust the transparency level of On-Screen Display (OSD), set the duration of the banner when switching channels, select automatic or manual mode for changing to reserved channel and set the duration of the reminder.
GB 35
User Manual - Page 48
.... 3.
Software Upgrade
14. OTA is only limited to certain geographical regions mainly due to update software. • Scheduling operation cannot work during software update. The software update via satellite will not activate while software update takes place. • It may take 5 ~10 minutes to different antennas having different footprints(area where the signal can be received). If...
User Manual - Page 49
... off and on. GB 48 When new software is not found by automatic update, use manual update. 14. Software Upgrade
Updating software is largely divided into two ways, automatic and manual search in MENU-System Settings-System Information-Software Upgrade. Select Automatic Search to 5.2.2 Manual Search.
For more information about how to set the manual search, refer to search pre-defined...
Humax DT9500CI Reviews
We have not received any reviews for Humax yet.