Husqvarna 525iECS Support and Manuals
Get Help and Manuals for this Husqvarna item
View All Support Options Below
Free Husqvarna 525iECS manuals!
Problems with Husqvarna 525iECS?
Ask a Question
Free Husqvarna 525iECS manuals!
Problems with Husqvarna 525iECS?
Ask a Question
Popular Husqvarna 525iECS Manual Pages
Owner Manual - Page 2
Speak to increase your servicing dealer for more information.
Work is constantly in progress to your...use the product for lawns. Note: National regulations can set limit to cut edges for other tasks than lawn edging.
Contents
Introduction 2 Safety 4 Assembly 11 Operation 14 Maintenance 16
Troubleshooting 18 Transportation, storage and disposal 18 Technical data 19 ...
Owner Manual - Page 3
Be careful and use .
Read the operator's manual carefully and make sure that you understand the instructions before maintenance. Use approved hearing protection.
Keep a minimum distance of 15 m to the operator or others.
Cutting attachment guard 4. Drive disc 8. Support flange 10. User interface 19. Speed mode button 21. Battery 23.
The blade continues ...
Owner Manual - Page 4
...repaired with parts that are not from the manufacturer or not approved by the manufacturer.
• the product has an accessory that the cutting blade and cutting guard are not damaged or cracked. Failure to follow the warnings and instructions may result in the presence of
damage to in the manual... service center or by an approved authority. Check that all warnings and instructions for...
Owner Manual - Page 6
...to be injured by a qualified repair person using the machine, always ...replacement cutting heads and trimmer cutters or lines specified by the manufacturer or authorized service providers.
Charging improperly or at temperatures outside the temperature range specified in the instructions...8226; Keep all parts of debris. Incorrect replacement parts may result in personal...
Owner Manual - Page 7
...the safety checks, maintenance and service instructions described in the use of the...manual.
• Children should consult an expert before moving.
• Never put the product down without approval from its initial specification. This can result in case you use parts that could be supervised to given regulations. General safety instructions
WARNING: Read the warning
instructions...
Owner Manual - Page 8
...or stones can result in a particular installation. Le présent appareil est...Part 15 of the eyes.
8
1847 - 002 - 13.02.2023 These limits are wearing hearing protection. This product meets the applicable Innovation, Science and Economic Development Canada technical specifications...com/us/support/e-mail/
Personal protective equipment
WARNING: Read the warning
instructions that ...
Owner Manual - Page 9
... or
flashes, refer to Troubleshooting on . See instructions under the heading Introduction on the display is not a servicing dealer, ask him for ...service and/or repairs are located on twigs and branches. B
A
C
CAUTION: All servicing and repair work
on the product
WARNING: Read the warning
instructions that it repaired. When you need further information please contact your service...
Owner Manual - Page 11
... and servicing shown in the opposite direction to your product.
• Only use original spare parts. Turn...in this operator's manual are professional repairs and servicing available for maintenance
WARNING: Read the warning
instructions that the cutting attachment... or assemble the product.
• The operator must be replaced after you have done maintenance, turn to the direction of...
Owner Manual - Page 12
... disc, that its outer edge presses against the blade.
5. Fit the locknut / blade mounting bolt (D). a) For model 525iECS:
E
C A
D
B
12
1847 - 002 - 13.02.2023 Fit the support flange (C). a) For model 525iECS:
A B
b) For model 525iES:
C D
A E
B
b) For model 525iES:
B A
To assemble the cutting attachment WARNING: Never use a cutting
attachment without an approved cutting attachment...
Owner Manual - Page 13
...13
To install the harness support hook
1.
Adjust the ring to make
it . Adjust the length of the cutting attachment guard.
2. To install the front ...Tighten the wing nut. Refer to use . Install the harness support hook between the loop handle and the throttle ...
support hook is in level with your right hip. Battery information
Refer to the operator's manual of the loop handle. 3. Set ...
Owner Manual - Page 14
...of the product. • Do the safety inspections, maintenance and
servicing that stops the product if the product is not installed correctly. Use the power trigger to the product.
3. To ...damage to control the speed.
The green LED for start position. 2.
Put the product in this manual. • Make sure that all nuts and screws are obstacles such as stones, branches and ditches...
Owner Manual - Page 16
... is a list of the product with Husqvarna Fleet Services™
1. Maintenance Clean the external parts of the maintenance steps that the start and stop button...Replace the cutting attachment guard if it is also possible for more information about Husqvarna Fleet Services™, refer to the Husqvarna Fleet Services™ app.
3. Husqvarna Fleet Services™
Husqvarna Fleet Services...
Owner Manual - Page 17
... while inserting it so that the bevel gear is filled to be changed except if repairs are clean before the battery is put in the bevel gear does not normally need ...dirt.
Reinsert the flexible driveshaft in the bevel gear.
6. a) For model 525iECS:
b) For model 525iES:
To lubricate the flexible drive shaft
Only for model 525iECS. 1. Clean the product with a dry cloth. Lubricate the ...
Owner Manual - Page 18
...Speak to a person with your local authorities, domestic waste service or your dealer for electrical and electronic equipment.
The ...battery. The cutting attachment is active. ange
Red error LED flashes
Overload. Put the battery in the ... action Charge the battery. Let the product cool down. Troubleshooting
User interface
LED display
Possible faults
Battery LED indicator flashes ...
Owner Manual - Page 19
... data for equivalent sound pressure level for the product has a typical statistical dispersion (standard
deviation) of 3 dB (A). 3 Reported data for lawn edger. na.com/uk/services-solutions/vibration-calculator/.
1847 - 002 - 13.02.2023
19 Vibration levels 3
Vibration levels at the operator's ear, measured according to IEC 62841-1, m/s2
1.3 / 1.2
1.6 / 1.8
Equipped with...
Husqvarna 525iECS Reviews
We have not received any reviews for Husqvarna yet.