Owners Manual
Page 1
...the underside of the deck baffle weldment as shown in the illustration. 3. Clean any grass out from underneath the deck. 1 1 2 2 4. INSTALLATION INSTRUCTIONS 60" MULCH KIT - 966 444701 IMPORTANT: BEFORE PROCEEDING, PLACE ALL CONTROLS IN THE DISENGAGED OR OFF POSITION, REMOVE SPARK PLUG WIRES FROM THE SPARK PLUGS. Block... the front of the mower up to give access to the outside of the front deck. P/N 115 247027 R1 08/15/09 Set the assembly and hardware aside for...
...the underside of the deck baffle weldment as shown in the illustration. 3. Clean any grass out from underneath the deck. 1 1 2 2 4. INSTALLATION INSTRUCTIONS 60" MULCH KIT - 966 444701 IMPORTANT: BEFORE PROCEEDING, PLACE ALL CONTROLS IN THE DISENGAGED OR OFF POSITION, REMOVE SPARK PLUG WIRES FROM THE SPARK PLUGS. Block... the front of the mower up to give access to the outside of the front deck. P/N 115 247027 R1 08/15/09 Set the assembly and hardware aside for...
Owners Manual
Page 3
Wet grass does not mulch well and grass accumulates under deck. INSTALLATION INSTRUCTIONS 7. Make sure all hardware is 3", the mower deck cutting height should be set at maximum. • Blades must be kept sharp. • The underside of deck should not exceed 1/3 of all baffles. 9. P/N ... kit mulching blades using the existing blade bolt (torque to its normal position. Example: If grass height is tight. 10. Remove blocks and return the mower to 90 ft./lbs.). 8.
Wet grass does not mulch well and grass accumulates under deck. INSTALLATION INSTRUCTIONS 7. Make sure all hardware is 3", the mower deck cutting height should be set at maximum. • Blades must be kept sharp. • The underside of deck should not exceed 1/3 of all baffles. 9. P/N ... kit mulching blades using the existing blade bolt (torque to its normal position. Example: If grass height is tight. 10. Remove blocks and return the mower to 90 ft./lbs.). 8.
Installation Instructions
Page 3
.... In the front, blade tips should be equal from the floor surface up until rear blade tips are sharp. Faulty mower deck adjustments will place the mower deck in front-to align with a heavy cloth when handling. 22. If adjustment is required, loosen the locknut and adjust...Measure from side-to leveling the deck. 20. Turn both side-to the correct pressure. Four bolts control the height and pitch of the mower deck. Confirm measurements once again. Locknut a b 8065-037 If tires are inflated to -side measurements are equal. Wear heavy gloves. Blade ...
.... In the front, blade tips should be equal from the floor surface up until rear blade tips are sharp. Faulty mower deck adjustments will place the mower deck in front-to align with a heavy cloth when handling. 22. If adjustment is required, loosen the locknut and adjust...Measure from side-to leveling the deck. 20. Turn both side-to the correct pressure. Four bolts control the height and pitch of the mower deck. Confirm measurements once again. Locknut a b 8065-037 If tires are inflated to -side measurements are equal. Wear heavy gloves. Blade ...
Installation Instructions
Page 5
... position 2½" to 4" (63 to 102 mm) grass. • Lower position 4" to 5" (102 to support the deck. IMPORTANT INFORMATION Adjust anti-scalp rollers with the mower on a flat level surface.
... position 2½" to 4" (63 to 102 mm) grass. • Lower position 4" to 5" (102 to support the deck. IMPORTANT INFORMATION Adjust anti-scalp rollers with the mower on a flat level surface.
Parts Manual
Page 3
CONTENTS FRAME 4 ENGINE MOUNTING, GUARDS AND MUFFLER 6 STEERING 8 IGNITION SYSTEM 10 PARKING BRAKE 12 HYDRAULIC PUMP-MOTOR 14 WHEELS & TIRES 16 MOWER LIFT / DECK LIFT 18 PEDALS 20 MOWER DECK / CUTTING DECK 22 SPINDLE ASSEMBLY 24 BELT GUARDS AND PULLEYS 26 SEAT 28 DECALS 30 Illustrations may or may not represent the actual assemblies and it is not recommended to use this manual as a guide to assemble or disassemble the mower. NOTE: All fasteners are Grade 5 unless otherwise specified.
CONTENTS FRAME 4 ENGINE MOUNTING, GUARDS AND MUFFLER 6 STEERING 8 IGNITION SYSTEM 10 PARKING BRAKE 12 HYDRAULIC PUMP-MOTOR 14 WHEELS & TIRES 16 MOWER LIFT / DECK LIFT 18 PEDALS 20 MOWER DECK / CUTTING DECK 22 SPINDLE ASSEMBLY 24 BELT GUARDS AND PULLEYS 26 SEAT 28 DECALS 30 Illustrations may or may not represent the actual assemblies and it is not recommended to use this manual as a guide to assemble or disassemble the mower. NOTE: All fasteners are Grade 5 unless otherwise specified.