Icom IC-F8100 Support and Manuals
Get Help and Manuals for this Icom item
View All Support Options Below
Free Icom IC-F8100 manuals!
Problems with Icom IC-F8100?
Ask a Question
Free Icom IC-F8100 manuals!
Problems with Icom IC-F8100?
Ask a Question
Popular Icom IC-F8100 Manual Pages
Instruction Manual - Page 2
... LCD for remote control
IMPORTANT
READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the
transceiver. SAVE THIS INSTRUCTION MANUAL.
CAUTION Equipment damage may occur. i
This
manual contains important safety and operating instructions for optimum use. NOTE
Recommended for the IC-F8100. We appreciate you making the IC-F8100 your IC-F8100.
R WARNING!
Instruction Manual - Page 3
...Icom dealer or distributor for long period of time. BE CAREFUL!
Other manufacturers' microphones have different pin assignments, and connection to the IC-F8100... DC plug and fuse holder.
CAUTION: NEVER install the transceiver in an electrical shock or burn.... NEVER change the internal settings of the transceiver. The transceiver warranty does not cover any problems caused by ignition voltage...
Instruction Manual - Page 8
... a PC via an RS-232C cable (D-sub
9-pin) for automatically setting your position and time data.
w A CCESSORY CONNECTOR 2 (12 PIN) [ACC2] e A CCESSORY CONNECTOR 1 (10 PIN) [ACC1] Connect to use this Junction Box.
Connects a ground.
4
Both connectors must be connected to the IC-F8100's Accessory connectors.
e GPIO CONNECTOR [GPIO] Connects a control cable to an...
Instruction Manual - Page 11
... and OFF.
• T he display shows the volume level while adjusting.
N OTE: The scan resume setting (the action after signal receiving) can be adjusted in "Scan Resume" of the User Menu.
5
Mute ...meter squelch level can be turned OFF.
■ Scan function
Scan function repeatedly scans programmed channels. When you need to receive weak signals, the squelch should be changed in...
Instruction Manual - Page 12
... Mode selection
The following modes are selectable in the IC-F8100: LSB, USB, CW, AM, D1,* D2* and D3 modes.
* W hen the "Modem" setting (p. 32) in the Admin Menu is displayed top ...Lock."
[�] [Default] [�]
r Push [t](§) or [u](§§§) to the default setting. w Push [r] or [s] to return the original operating mode
■ Key Lock function
To prevent ...
Instruction Manual - Page 14
... Push [r] or [s] to reset the tuner.
10
D Tuner through function
In the combination with IC-F8100 and optional AT140, the tuner through function ON. • "TUNE" disappears. • Push [...HOME) for 1 second to return to the normal operating mode.
w Push [r] or [s] to the default setting.
e Push [r] or [s] to select "RF Power."
[�] [Default] [�]
r Push [t](§...
Instruction Manual - Page 15
... to transmit.
• Speak into the microphone, check the TX
3
meter reading.
ï Speech Processor
IC-F8100 has a built-in SSB mode and is especially useful when the receiving station is having difficulty copying your signal....Default](§§) for 1 second to the
default setting. w Push [r] or [s] to the nor- u While speaking into the microphone at a normal voice...
Instruction Manual - Page 20
... a system which automatically selects an available frequency and establishes a communication link. The IC-F8100 ALE system compiles with other brands. (Icom Selcall system)
• Depending on the preprogramming. Check the selcall or ALE capabilities in the Admin Menu, and then set the settings to RX&TX.
ï Available calls
• Selective call The Selective call...
Instruction Manual - Page 43
... own Icom standard address in 1 steps or AUTO.
(default: AUTO) AUTO: S ame setting as your group to set items, Blanker Level, AGC, Bandwidth, Clarifier, Pre Amp, Speech Processor, Processor Level, Key Lock and Side Tone Level appear in the User Menu and Admin Menu without clearing memory channel contents or ID contents.
The IC-F8100...
Instruction Manual - Page 44
...4 t Black and red cables with fuse holders 1 set y Spare fuses (ATC 30 A 2 u Microphone hanger kit 1 set i Crimp terminals 2 o Remote controller with mounting bracket 1 !0 Separation kit 1 set i Crimp terminals 2
q
w
D #02 (Separation Type)
The following accessories are supplied with IC-F8100 #02. e
r
q
w
t
y
u
i
e
r
t
y
u
i
o
!0
40 q Microphone (HM-193 1 w External...
Instruction Manual - Page 45
... (Remote control microphone Type)
The following accessories are supplied with fuse holders 1 set y Spare fuses (ATC 30 A 2 u Microphone hanger kit 1 set i Crimp terminals 2 o Extension MIC connector 1 *Separation cable is not supplied. q Remote control microphone (HM-192 1 w External speaker (SP-25 1 e DC power cable (OPC-2140 1 r Stands 4 t Black and red cables with IC-F8100 #03.
Instruction Manual - Page 47
... (10
m): m):
4 6
pin pin
OPC-2143 (5 m)
5 6
7
8
D O NOT pull the antenna and control cable re- 6 CONNECTION AND INSTALLATION
Quick Reference
CAUTION: DO NOT transmit continuously while connecting AT230, otherwise AT230 will be damaged. AT230 Optional AT-140
IC-F8100 main unit
Grounding (see p. 44)
Grounding (see p. 44)
1
to a 13.8 V DC power souce
2
to
to secure...
Instruction Manual - Page 50
...Main unit for added installation convenience and operation. 7 CONNECTION AND INSTALLATION
■ RMK-6 (Optional Separation kit)
The RMK-6 allows you to install the IC-F8100's Front panel separately...RMK-6's Front panel attachment and Main unit attachment as the separation kit for separately installing the transceiver Front panel and Main Unit. D Supplied Accessories
D Separation The optional ...
Instruction Manual - Page 55
... danger of the problem, and repair it. e R eplace the circuitry fuse as shown in the diagram below. • Use the supplied ATC 5 A fuse.
nect the DC power cable from the bottom cover, then lift
up the bottom cover.
The IC-F8100 has two fuse types installed for the DC power cable fuse replacement.
7
ATC 30 A fuse...
Instruction Manual - Page 58
...;
HM-193 hand microphone Same as supplied with the IC-F8100 #02 (Separation Type).
Limited The AT230 is a 2.6 m length mobile whip antenna with the speaker. Use the optional OPC-2143 cable for easy installation and tuner through function are available.
Allows you to separately install the transceiver Front panel from Moonraker Australia Pty. AD...
Icom IC-F8100 Reviews
We have not received any reviews for Icom yet.