Icom M400BB Support and Manuals
Get Help and Manuals for this Icom item
Popular Icom M400BB Manual Pages
Instruction Manual - Page 1
COMMANDMICIV™ (HM-195) may not be supplied, depending on the transceiver version. Operation is subject to the condition that this device does not cause harmful interference. INSTRUCTION MANUAL
VHF MARINE TRANSCEIVER
iM400BB
This device complies with Part 15 of the FCC Rules.
Instruction Manual - Page 2
...-M400BB.
i
IMPORTANT
READ ALL INSTRUCTIONS carefully and completely
before using the
optional MA-500TR Class B AIS Transponder
* May not be supplied, depending on the transceiver version. In that case, purchase separately. The IC-M400BB vhf marine transceiver is designed and built with Icom's state of personal injury, fire or electric shock. With proper care, this Icom...
Instruction Manual - Page 3
... selected. 3. Hold down [DISTRESS]
for 3 seconds until you have one long beep. 2. Wait for maximum efficiency and the installation height should be continuously operated for revised installation recommendations. Keep your position). 5. Or, transmit your Icom distributor for long periods if any person is within a distance of 1.4 meters of the vessel (AND
9 digit DSC...
Instruction Manual - Page 4
...not greater than the allowable MPE level set by a grounded metallic barrier.
This ...GAIN OF 9dBi ARE USED FOR A SHIP MOUNTED SYSTEM. RADIO OPERATOR WARNING
Icom requires the radio operator to meet all RF exposure compliance requirements. An ...order to avoid RF exposure higher than 9 dBi must be mounted so as driver or radio operator) are within the MPE radius of the antenna, unless such ...
Instruction Manual - Page 6
... harmful interference in the diagram below. COUNTRY CODE LIST
• ISO 3166-1
Country
Codes
Country
Codes
1 Austria
AT 18 Liechtenstein
LI
2 Belgium...instruction manual, may cause harmful interference to part 15 of the radio as to be required to correct the interference at his own expense. This equipment generates, uses, and can radiate radio frequency energy and, if not installed...
Instruction Manual - Page 8
... 6 ■■Supplied accessories 8 ■■Fuse replacement 8 ■■ Cleaning 8
vii
■■Mounting the transceiver 8 ■■ Antenna 8 ■■Microphone installation 9
5 SPECIFICATIONS AND OPTIONS 11-12 ■■ Specifications 11 ■■ Options 12
6 CHANNEL LIST 13-14
7 TROUBLE SHOOTING 15 TABLE OF CONTENTS
FOREWORD i IMPORTANT...
Instruction Manual - Page 10
... is displayed.
After being set it . yyThe "MMSI CONFIRMATION" screen is displayed.
To program the MMSI code, turn OFF the power,...code in the MENU screen. 2 PREPARATION
■■MMSI code programming
The 9 digit MMSI (Maritime Mobile Service Identity: DSC self ID) code can be required after programming the MMSI code. NOTE: Depending on the transceiver version, the ATIS code...
Instruction Manual - Page 11
... the following manner: • Select a desired number using the HM-195. In this programming is displayed.
4
This initial code setting can be performed only once.
5
After being set it ON again. To program the ATIS code, turn OFF the power, then turn it . • T o move the cursor, select either arrow, "←" or "→," then...
Instruction Manual - Page 12
... If the transceiver cannot make the call type is automatically set the CH70 SQL LEVEL. erwise, you cannot make sure you... the detail screen of the HM-195 instruction manual. See page 7 for connecting instructions. To ensure correct operation of the DSC... function, make an individual DSC call can also go to enter the target's MMSI code...
Instruction Manual - Page 14
nector.
White: Talker A (Data-H)
Connects to an NMEA In Positive line of a PC or NMEA0183
ver. 3.01 sentence format DSC,...: Public Address Speaker (-) Connects to a PA speaker. • PA output power: More than 10 W at 10% distortion with a 4 ˘ load
Both black and blue leads are attached to a marine VHF antenna cable's PL-259 con- NOTE for NMEA In/Out and AF Out leads: The...
Instruction Manual - Page 15
...code.
* The OPC-2014 is correct. Red : Positive + terminal Black : Negative _ terminal
CAUTION: After connecting the DC power cable, NMEA leads, external speaker leads and PA speaker...M400BB and HM-195
separately.
6
When connecting the HM-195 for the first time,
7
a firmware update...A (Data-H) lead (White): Connects to lead 5 of the OPC-2014.
7 The update
10
will automatically
8
...
Instruction Manual - Page 16
...problem, repair it clean with a new one of any communication system is the antenna.
A key element in the performance of the proper rating.
■■Mounting the transceiver
Using the supplied template on the leaflet, mount the ICM400BB securely to a surface which is installed...9632;Fuse replacement
One fuse is more than 10 mm thick and can support more than 5 kg using the ...
Instruction Manual - Page 20
... is not manufactured or approved by Icom.
12 5 SPECIFICATIONS AND OPTIONS
DDDimensions
216 (8.5) 165 mm (6.49)
108.3 (4.26)
124.5 (4.9)
190 (7.48)
Unit: mm (inch)
42 (1.65) 79 (3.11)
■■Options
• HM-195 commandmiciv™ External microphone-type controller. 6 m (20 ft) microphone
cable included.
Black and white colors are available.
• OPC-1541...
Instruction Manual - Page 21
... 156.525 80 157.025 161.625
9
*1 DSC operation only.
10
*2 Channels 15 and 17 may also be used in its territorial 11
waters.
12
*3 UK Marina Channels: M1=37A (157.850 MHz), M2=P4 (161.425 MHz) for example by means geographical separation.
14
15
16
13 The use of...
Instruction Manual - Page 23
7 TROUBLE SHOOTING
PROBLEM
POSSIBLE CAUSE
SOLUTION
REF.
1
The transceiver does • Bad connection to the power supply.
• Check the connection to the HM-195 commandmiciv™ instruction manual.
13
14
15
16
15 power or receive only by regulations.
grammed.
12
* Refer to the transceiver and p. 6
2
not turn ON. b*,
6
ble, or high power ...
Icom M400BB Reviews
We have not received any reviews for Icom yet.