Icom M803 Support and Manuals
Icom M803 Videos
Popular Icom M803 Manual Pages
Instruction Manual - Page 1
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INSTRUCTION MANUAL
MF/HF MARINE TRANSCEIVER
|M803
This device complies with Part 15 of the FCC rules.
Instruction Manual - Page 2
..., this Icom product.
Icom, Icom Inc. zz Built-in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia, Australia, New ...Icom or Non-Icom equipment, if the malfunction is needed: 1. Wait for choosing this product should provide you with Icom's state of troublefree operation.
This instruction manual includes some functions that is not responsible for the IC-M803...
Instruction Manual - Page 7
...Push the key below the desired function.
Go back to enter or set. The following keys on the rear panel do not meet IPX7....level
Push [ENT], [CH/GRP], [►]
or
.
Contact your Icom distributor or your dealer for advice.
FUNCTION Select
ACTION Push [▲] ... display. KEY ICON DESCRIPTION
The keys are described in this manual as follows:
The keys that have words or letters on...
Instruction Manual - Page 8
... PREPARATION 9
Entering the MMSI code 9
4 MENU SCREEN 10
...Settings 65
Radio Information 67
CONNECTIONS AND INSTALLATION...Icom...installation 74 Transceiver dimensions 75
Acknowledgment 43 Fuse replacement...SPECIFICATIONS AND
DD Receiving a Distress Cancel call��45 DD Receiving a Distress Relay call��46
OPTIONS 80
DD Receiving a Distress Relay
11 TROUBLESHOOTING...
Instruction Manual - Page 12
... to enter numbers, letters, or symbols.
6 TUNE KEY [TUNE] When the AT-140 or AH-3 is connected: zzPush to start manual tuning.
7 POWER KEY [ ] Hold down to display the setting screens.
zzHold down for 1 second to turn the transceiver ON
or OFF.
4
8 VOLUME DIAL [VOL] zzRotate to adjust the speaker volume...
Instruction Manual - Page 16
LLThe manually entered data is set. Local Displayed when the offset time is held for only 23.5 hours. LLAfter 23.5 hours has passed, "No Time" ... Time area •• The current time is displayed when valid GPS data
is received, the time is manually entered. •• The date information is invalid. Blinks every 2 seconds instead of the time after 4 hours have passed since...
Instruction Manual - Page 17
... step 3 to set the
•• The "MMSI CONFIRMATION" screen is also displayed on the opening screen.
4. Enter the MMSI code. After entering, it ON again.
3. Hold down [ ] to confirm. Push
to enter all 9 digits. 5. You can be entered only once. 3 PREPARATION
■■Entering the MMSI code
The Maritime Mobile Service Identity (MMSI...
Instruction Manual - Page 22
... to transmit a CW signal. LLITU FSK channel group, Ch 4001 to Ch 22026, are
usable only when the "ITU FSK CH" setting is necessary before keying. Select the desired channel to
"ON." (p. 66)
3. zz OFF: Manual transmission with the
microphone's [PTT] switch, or grounding the SEND line of the [ACC] connector is...
Instruction Manual - Page 34
..."Position Input."
[MENU] > DSC Settings > Position Input
2. Push [MENU] or
to return to the Main
screen.
•• The entered position data and time, and "Manual" is
displayed in the Position data ...on the screen and push [ENT], or push a Keypad key when the cursor is received, manually enter the position and Universal Time Coordinated (UTC) time. 7 DSC OPERATION
■■Entering...
Instruction Manual - Page 45
...-DISTRESS" screen is set to "AUTO," the transceiver automatically transmits an Individual Acknowledgment. (p. 57)
DDSending a Group call
A Group call to
the Main screen.
Rotate
7
+ Push
3. Push
, and then
to return to only a specific group.
Confirm the contents. Rotate
+ Push
NOTE: When you to send a DSC call enables you select "Manual Input" in the...
Instruction Manual - Page 51
Push
.
•• The received call's information is set to "AUTO," the transceiver automatically transmits a Test Acknowledgment. (p. 57)
DSC...push to turn OFF the alarm.
2. DDSending a Test call Acknowledgment
When you have received a Test call is set to "Manual" (p. 57), do the following steps to send an Acknowledgment.
1. LLIf you want to immediately send an Acknowledgment,...
Instruction Manual - Page 65
...8226;• Auto (Able): Automatically sends "Able to comply."
•• Auto (Unable): Automatically sends "Unable to comply."
•• Manual: Manually sends an Acknowledgment.
Open "Auto ACK."
[MENU] > DSC Settings > Auto ACK
2. DSC OPERATION 7
When selecting or editing "Routine frequency" 1. Select a channel. Rotate
+ Push
3.
zz Test ACK
Rotate...
Instruction Manual - Page 66
... transceiver remains on the
current operating channel.
•• Manual:
After receiving a DSC call, you set this setting. 1. Rotate
+ Push
•• All stations: From any DSC data
from the station that is entered. •• The received position data has not been updated
for 10 minutes. •• The position data has not...
Instruction Manual - Page 80
... non-Icom tuners may be entirely usable.
However, these antennas cannot be connected directly to connect one.
The following antenna matcher and antenna tuner may not be helpful for DSC reception. Backstay Antenna
MN-100/MN-100L
When the antenna is used with a whip or long wire antenna. 9 CONNECTIONS AND INSTALLATION
■...
Instruction Manual - Page 90
...code is not set to the power supply.
→→Check the connection between '1' and '9' for low power or receive only by regulations.
→→Change channels. (p. 12)
zz The output power is blown.
→→Repair the problem, and then replace...be set
→→Set the MMSI (DSC self ID) code. (p. 9)
Individual or Group ID cannot be established.
zz The software error ...
Icom M803 Reviews
Do you have an experience with the Icom M803 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Icom yet.
Earn 750 points for your review!