Instruction Manual
Page 4
... can use wires with one of any switch. • If the fuse blows, check wires for KAC-X1R.) 2CAUTION • Before connecting the remote controller cables, always turn the Bass boost level knob all the way to appropriate speaker connectors separately. FUSE (25As3) POWER IN Battery wire* Protective Fuse...by twisting it. 3 Install the wire Loosen the screw using the supplied hexagon wrench. CENTER UNIT (CD receiver, etc.) RCA cable* Power control wire 2CAUTION • If sound is not output normally, immediately turn the power off and check connections. • Be sure to fail. ...
... can use wires with one of any switch. • If the fuse blows, check wires for KAC-X1R.) 2CAUTION • Before connecting the remote controller cables, always turn the Bass boost level knob all the way to appropriate speaker connectors separately. FUSE (25As3) POWER IN Battery wire* Protective Fuse...by twisting it. 3 Install the wire Loosen the screw using the supplied hexagon wrench. CENTER UNIT (CD receiver, etc.) RCA cable* Power control wire 2CAUTION • If sound is not output normally, immediately turn the power off and check connections. • Be sure to fail. ...
Instruction Manual
Page 5
...) Master amplifier POWER IN 25 25 25 SPEAKER OUTPUT LINE OUT FILTER REMOTE OFF ON RESET LINE IN LINE OUT LINE OUT FILTER Remote controller 2CAUTION • Before connecting the remote controller cables, always turn the Bass boost level knob all the way to "0.2 V (max.)". Optional accessory for KAC-X1R.) You can control the Bass boost level of the remote controller).
...) Master amplifier POWER IN 25 25 25 SPEAKER OUTPUT LINE OUT FILTER REMOTE OFF ON RESET LINE IN LINE OUT LINE OUT FILTER Remote controller 2CAUTION • Before connecting the remote controller cables, always turn the Bass boost level knob all the way to "0.2 V (max.)". Optional accessory for KAC-X1R.) You can control the Bass boost level of the remote controller).
Instruction Manual
Page 6
... control Sets the cutoff frequency when the "LPF" switch is set to "ON". * BOOST LEVEL (Bass boost level) control Sets the level by eliminating unnecessary oscillations which the low frequency range should be boosted....with the "LPF FREQUENCY" control. ( INPUT SENSITIVITY control Set this unit. NOTE Use the Remote cable of the amplifier. NOTE For the pre-output level, refer to the in ..."ON" to "OFF". 8 RESET button Resets the microprocessor of the audio output to its controls for KAC-X1R.) 25 25 25 SPEAKER OUTPUT FUSE (25As3) POWER IN p q rs t LINE OUT FILTER...
... control Sets the cutoff frequency when the "LPF" switch is set to "ON". * BOOST LEVEL (Bass boost level) control Sets the level by eliminating unnecessary oscillations which the low frequency range should be boosted....with the "LPF FREQUENCY" control. ( INPUT SENSITIVITY control Set this unit. NOTE Use the Remote cable of the amplifier. NOTE For the pre-output level, refer to the in ..."ON" to "OFF". 8 RESET button Resets the microprocessor of the audio output to its controls for KAC-X1R.) 25 25 25 SPEAKER OUTPUT FUSE (25As3) POWER IN p q rs t LINE OUT FILTER...
Instruction Manual
Page 8
.../ -6 dB/ -12 dB Band Reject Filter Frequency...40 - 200 Hz (variable) Phase Inverter ...0° (Normal) / 180° (Reverse) Bass Boost Circuit...0 - 18 dB (variable) Bass Boost Frequency...40 - 100 Hz (variable) Bass Boost Frequency...General Operating Voltage ...14.4 V (11 - 16 V allowable) Current Consumption ...75 A Installation Size (W × H × D) ...340 ...kg (8.38 lbs) Weight ... 8 English Before calling service, first check the following table for possible problems. PROBLEM No sound. (Blown fuse.) The output level is distorted.) The Remote Controller does not function.
.../ -6 dB/ -12 dB Band Reject Filter Frequency...40 - 200 Hz (variable) Phase Inverter ...0° (Normal) / 180° (Reverse) Bass Boost Circuit...0 - 18 dB (variable) Bass Boost Frequency...40 - 100 Hz (variable) Bass Boost Frequency...General Operating Voltage ...14.4 V (11 - 16 V allowable) Current Consumption ...75 A Installation Size (W × H × D) ...340 ...kg (8.38 lbs) Weight ... 8 English Before calling service, first check the following table for possible problems. PROBLEM No sound. (Blown fuse.) The output level is distorted.) The Remote Controller does not function.