Kenwood NX-920G Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood NX-920G manuals!
Problems with Kenwood NX-920G?
Ask a Question
Free Kenwood NX-920G manuals!
Problems with Kenwood NX-920G?
Ask a Question
Popular Kenwood NX-920G Manual Pages
Operation Manual - Page 3
ENGLISH
VHF DIGITAL TRANSCEIVER UHF DIGITAL TRANSCEIVER 800MHz DIGITAL TRANSCEIVER
NX-720H NX-720HG NX-820H NX-820HG NX-920 NX-920G
INSTRUCTION MANUAL
Operation Manual - Page 4
Terminal Descriptions
ACC (D-SUB 15 Pin Connector)
Pin No. Ground
Speaker Jack (3.5 mm Phone Jack) 4 W/ 4
Pin No. Name
I /O Mic Data Detection
RF Antenna Terminal 50 impedance GPS Antenna Terminal 50 impedance
Specification 13.6 V ±15% Max. 2 A Min.
Input: 16.0 V 4 280 mVp-p (typ.) 100 k High Impedance High Impedance High ...
Operation Manual - Page 5
... fine and/or imprisonment. ◆ Refer service to comply with a padded interior. Ask your dealer for your transceiver when in an area where blasting is no guarantee that to which can generate radio frequency energy and, if not installed and used in the instruction manual. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY...
Operation Manual - Page 7
... passed through. • If no hole exists, use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory. If your vehicle may malfunction if they are missing or have been damaged during shipment, file a claim with 4 x 16 mm self-tapping screws 1 Instruction manual 1
PREPARATION
Various electronic equipment in 12 V negative ground systems...
Operation Manual - Page 9
d TX/RX Indicator Lights red while transmitting and green while receiving a signal. f Status Indicator Lights blue during a specified mode, based on dealer programming.
m GPS antenna connector Connect the KRA-40 GPS antenna to this connector.
Flashes orange when receiving an optional signaling call a station. i PTT switch Press this switch, then speak into this jack.
h ...
Operation Manual - Page 16
...and the transceiver will appear when a Selcall is a protocol owned by JVC KENWOOD Corporation. SELCALL (SELECTIVE CALLING)
A Selcall is a voice call ). FleetSync... the microphone.
■ Identification Codes An ID code is enabled, you want to 16 alphanumeric ...3 Press the / key to the call . • If Manual Dialing is a combination of 15 received messages (combined status messages ...
Operation Manual - Page 17
...second. If set up by your transceiver.
SHORT MESSAGES
This transceiver can enter a station ID by using the NX-720H/ NX-820H/ NX-920, you can ... the S or key. GPS REPORT
GPS data can be manually transmitted by pressing the key programmed as Status messages. A... at a preset time interval. • When using the NX-720HG/ NX-820HG/ NX-920G, you must connect a KRA-40 GPS
antenna. •...
Operation Manual - Page 22
... for 1 second. 3 Press the / key to select your desired tone or code.
• Your dealer can set up to 40 tones/codes. 4 When you can program a key with a RAN, squelch will not hear...only when the transceiver receives a call containing matching 2 tones (available only for NX-720H/ NX-720HG/ NX-820H/ NX-820HG).
This allows you cannot hear during normal operation and to adjust the volume ...
Operation Manual - Page 24
...transmit if the channel is already in analog operation.)
• Your dealer must set up by pressing the PTT switch again, immediately after releasing it, when the ...or [AUX B] to operate. PTT ID
PTT ID is the transceiver unique ID code which is sent each channel.
BACKGROUND OPERATIONS
TIME-OUT TIMER (TOT)
The Time-...transmit for NX-720H/ NX-720HG/ NX-820H/ NX-820HG), or low.
18
Instruction Manual - Page 3
... VHF DIGITAL TRANSCEIVER
NX-720H NX-720HG
UHF DIGITAL TRANSCEIVER
NX-820H NX-820HG
800MHz DIGITAL TRANSCEIVER
NX-920 NX-920G
INSTRUCTION MANUAL
The AMBE+2TM voice coding Technology embodied in KENWOOD product memories are reserved for use within this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of copyrights for firmware embedded in...
Instruction Manual - Page 4
Terminal Descriptions
ACC (D-SUB 15 Pin Connector)
Pin No.
Name
I/O
Description
1
SB
O DC Power (Switched B) Output
2
IGN
I Igintion Signal Input
3
SP2/PA
O Loudspeaker Output/ Public Address Output
4
DETO
O RX Detected Audio Output
5
DATAI
I TX Data Input
6
FNC1/ TXD I Horn Alert Signal Input
14
HR2
O Horn Alert Signal Output
15
GND
-
Input: 10.8 V Max...
Instruction Manual - Page 5
... installation....instruction manual covers only the basic operations of the following statements may be determined by fine and/or imprisonment. ◆ Refer service to Part... 15 of any customized features they are carried in accordance with a padded interior. Turn OFF your radio.
The user could lose the authority to operate this equipment may have chosen KENWOOD...
Instruction Manual - Page 7
... they will perform normally while transmitting.
■ Power Cable Connection
The transceiver operates in your KENWOOD dealer, an authorized KENWOOD service facility, or the factory. GETTING STARTED
Note: The following instructions are for use a circle cutter to drill a hole, then install a rubber grommet.
2 Run the power cable through the firewall and into the engine...
Instruction Manual - Page 9
b / keys Press to this switch, then speak into this connector, via the KCT-60.
d TX/RX Indicator Lights red while transmitting and green while receiving a signal.
m GPS antenna connector Connect the KRA-40 GPS antenna to activate their programmable functions {page 5}. f Status Indicator Lights blue during a specified mode, based on dealer programming. i PTT switch Press ...
Instruction Manual - Page 17
... • If Manual Dialing is enabled, you must connect a KRA-40 GPS
antenna. • When using the NX-720H/ NX-820H/ NX-920, you can enter...a preset time interval. • When using the NX-720HG/ NX-820HG/ NX-920G, you must connect an external GPS unit. •...To delete the selected message, press the A or # key.
If set up by pressing the key programmed as follows: ID Name > Status/...
Kenwood NX-920G Reviews
We have not received any reviews for Kenwood yet.