Kenwood TK-8360HU Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood TK-8360HU manuals!
Problems with Kenwood TK-8360HU?
Ask a Question
Free Kenwood TK-8360HU manuals!
Problems with Kenwood TK-8360HU?
Ask a Question
Popular Kenwood TK-8360HU Manual Pages
Instruction Manual - Page 3
ENGLISH
VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER
TK-7360H/ TK-8360H TK-7360HV/ TK-8360HU
INSTRUCTION MANUAL
Firmware Copyrights The title to and ownership of copyrights for firmware embedded in Kenwood product memories are reserved for JVC KENWOOD Corporation.
Instruction Manual - Page 5
...service stations. Turn OFF your transceiver when in an area where blasting is no guarantee that the interference will not occur in accordance with the instructions, may cause harmful interference to which can generate radio frequency energy and, if not installed and used in a particular installation...parked in the instruction manual. NOTICES TO...device, pursuant to Part 15 of any transceiver...
Instruction Manual - Page 6
...Kenwood dealer. • Use of the transceiver while you are driving may be against traffic laws. For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set... 12 TRUNKING CALLS 14 ADVANCED OPERATIONS 15 BACKGROUND OPERATIONS 18 VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT 19
ii PRECAUTIONS
Observe the following precautions to prevent fire, personal...
Instruction Manual - Page 7
... set • 5 x 16 mm self-tapping screw 4 • Hex-headed screw with washer 4 • Spring washer 4 • Flat washer 4 Microphone (with cable) • KMC-30 (TK-7360H/ TK-8360H 1 • KMC-35 (TK-7360HV/ TK-8360HU 1 Microphone hanger (with the carrier immediately.
SUPPLIED ACCESSORIES
Carefully unpack the transceiver. If your Kenwood dealer, an authorized Kenwood service...
Instruction Manual - Page 8
... break loose in the dash, using the mounting bracket as a template. Never replace a fuse with one that is sufficient space at the rear of the transceiver for servicing while keeping the power applied.
■ Installing the Transceiver
For passenger safety, install the transceiver securely using the supplied screws. • Mount the transceiver within easy...
Instruction Manual - Page 10
... zones, it will not appear when using Fix ID or Group ID enabled by dealer. Note: If this icon is on . The Scrambler function is set up for use in the stack memory. Signaling is the Channel/Group ID Recall channel. Lights while scanning or while paused on . The Horn Alert...
Instruction Manual - Page 11
...9632; keys can be programmed with the functions listed below. When assigned, the dealer must set the key assignment hold to "Enable" and second function as "Emergency".
5 Ask your dealer... ~ Status 3 • Stun (MDC-1200) • Talk Around • Telephone Disconnect • Transceiver Password • Voice Memo • Volume Down • Volume Up • Zone Del/Add • Zone Down...
Instruction Manual - Page 13
... of zones. The transceiver will remain paused on
the busy channel until you can temporarily remove specific channels from your desired zone and channel. 2 Press the microphone PTT switch and speak into the...is no longer scanned. SCAN
Scan monitors for a signal on the transceiver channels. If set up to the scan sequence. Scan will remain on the Recall channel until the signal is...
Instruction Manual - Page 15
... the cursor to the right.
• Press A or # to delete an incorrect digit. AUTODIAL
Autodial allows you must use an optional microphone with a DTMF keypad. MANUAL DIALING
1 Press and hold A or # to delete all digits.
10 Repeat steps 8 and 9 to enter the entire number. 11 Press S to transmit; Press and hold...
Instruction Manual - Page 18
... assignment list selection is configured as Paging Call to transmit your transceiver and can also manually send status messages.
12 Each transceiver must have its own Fleet and ID number.
Note... JVC KENWOOD Corporation.
STATUS MESSAGE
Status messages are reserved for special messages). Note: If set up by your dealer, your dealer, you want to 99 (80 ~ 99 are 2-digit codes ranging ...
Instruction Manual - Page 21
..., the transceiver will change to the Emergency channel and begin transmitting based on how the transceiver is set up.
2 To exit Emergency mode, press and hold the Emergency key again. • If the...as a power failure), you can continue to clearly hear what you are no geographical obstacles in service (such as Talk Around to toggle the Scrambler function ON or OFF. • The icon appears...
Instruction Manual - Page 22
... icon appears on the display while Monitor or Squelch Off is configured as "Enabled") or to select your
desired scrambler code. 3 Press S, , or to store the new setting.
• After changing your group members of your scrambler code, be sure to unlock the keys.
16 Your dealer can program a key with different scrambler...
Instruction Manual - Page 24
BUSY CHANNEL LOCKOUT (BCL)
If BCL is set up by your dealer, you will be high, medium, or low.
18 PTT ID
PTT ID is the transceiver unique ID code which is sent each channel. The auxiliary port is used with
optional boards.
• The
icon appears on the display when you press...
Instruction Manual - Page 25
... is no channel available on the display.
19
VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT
When using the optional VGS-1 voice guide & storage unit, you gain access to Individual Calls.
1 Press ... all transmitted and received
signals. VOICE RECORDER
The voice recorder provides you can set the transceiver to automatically respond to the voice recorder and voice announcement functions. ...
Instruction Manual - Page 26
VOICE GUIDE
If set up by dealer setting.)
20 Additionally, when changing a function setting, an audio voice will announce the new setting. (Voice announcements vary by your conversation, "STORE" will appear on the display, otherwise a recording channel with the time of the recording will appear.
2 Press / to ...
Kenwood TK-8360HU Reviews
We have not received any reviews for Kenwood yet.