Lacie 12big Rack Serial 2 Support and Manuals
Get Help and Manuals for this Lacie item
View All Support Options Below
Free Lacie 12big Rack Serial 2 manuals!
Problems with Lacie 12big Rack Serial 2?
Ask a Question
Free Lacie 12big Rack Serial 2 manuals!
Problems with Lacie 12big Rack Serial 2?
Ask a Question
Popular Lacie 12big Rack Serial 2 Manual Pages
Datasheet - Page 1
... resolved within 24 hours. It even supports mixed SAS and SATA drive configurations. 100% of the enclosures and 100% of failure.
Within the 12big Rack Serial 2, there is compatible with 12 drives • Fully redundant**
Fully Redundant-Fully Reliable
In addition to the 12 hot-swappable disks and individually tested enclosures, the LaCie 12big Rack Serial 2's I /O Module
Right Power...
Datasheet - Page 2
...
12 x 600GB
Hot-swappable enterprise class drives SAS 15 krpm or SATA II 7200 rpm (3Gb/s)
Single SAS I/O module
Mini SAS (SFF 8088): 1 x IN, 1 x OUT
SES (SCSI Enclosure Services) 2.0
Through daisy chaining of several LaCie 12big Rack Serial 2 units (96 SAS drives or 60 SATA drives)
Height: 87.9mm (3.46") 2 EIA units Width: 443.7mm (17...
Quick Install Guide - Page 2
... a replacement can weigh up to take the weight.
1.2.
INTRODUCTION
1.1. Safe Handling
ƒƒ A LaCie 12big Rack Serial 2 enclosure can be grounded before applying power. ƒƒ Provide a suitable power source with electrical overload protection to a telecommunications network. IMPORTANT: The enclosure MUST be immediately added.
Safety
ƒƒ All plug-in modules and...
Quick Install Guide - Page 3
... remove a PCM unless a replacement can be run without all conventional ESD precautions when handling plug-in the rack. The system must meet the safety requirements of electric shock inside. Earth connection essential before connecting supply". ƒƒ The rack when configured with the units must not be immediately added. LaCie Quick Install Guide
2 Rack System Precautions
The...
Quick Install Guide - Page 4
... and use with the correct firmware, BIOS and drivers. Before You Begin
Before you begin, make sure the site where you have the following: ƒƒ SAS HBA ƒƒ Mini-SAS to Host Cable ƒƒ Power Cord ƒƒ Rack kit (if installing within a rack)
Refer to set up your enclosure ensure you intend...
Quick Install Guide - Page 5
Inspect the packaging for future reference photograph the packaging before opening.
2.
See Figure 1. Unpacking the Storage System
1. Unpacking the Storage System
LaCie Quick Install Guide
4 If any damage appears present, for crushes, cuts, water damage or any other evidence of mishandling during transit. Figure 1 - Unpack the system. 2.2.
Quick Install Guide - Page 6
Attach left and right chassis slides to Enclosure
LaCie Quick Install Guide
5 Securing Chassis Slides to the enclosure sides using 8 M3 x 4 buttonhead screws (see Figure 2). 3. Mounting the System into a Rack
1. Remove the Rack Mounting Rail Kit from the Accessory Box and check for damage. 2.
INSTALLATION
3.1. Figure 2 -
Quick Install Guide - Page 7
... is orientated as follows (see Figure 3).
5. c. d. d.
Securing Brackets to the front rack post using the special chassis latch screws. b. Attach the bracket to Rack
3. b. LaCie Quick Install Guide
6 Assemble the left loose. Mount the enclosure into the rack as shown in Figure 2, with the rack rails. Lift the enclosure and align it reaches the hard stops (approx...
Quick Install Guide - Page 8
Figure 4 - e. Mounting the System into a Rack
LaCie Quick Install Guide
7 Return the enclosure to the fully home position.
Quick Install Guide - Page 9
... appropriate method mentioned in the LaCie 12big Rack Serial 2 User Manual. IMPORTANT: Connections can be updated using this product as an expansion chassis for several min-
3.2. of the system. • When using this product as an expansion chassis, software update may automatically occur. Figure 5 - Single Enclosure
LaCie Quick Install Guide
8 utes for the update and then reboot of...
Quick Install Guide - Page 12
No Activity Host Port Connection Activity I/O Module VPD Error X = Disregard
I/O Module Fault (Amber) Off On X X X X
I /O Module LED States
Figure 8 - I /O Module OK (Green) On Off X X X Flashing
Host Port Activity (Green) X X Off Off Flashing X
LaCie Quick Install Guide
11 LED STATES
4.1. I/O Module LEDs
Status
I/O Module OK I/O Module Fault No Host Port Connection Host Port ...
Quick Install Guide - Page 14
4.3. Drive LED States
Status
No drive installed Drive installed and operational
SES device identity set SES device fault bit set Power control circuit failure Failed disk array X = Disregard
Green LED
Amber LED
Off On/Blink with ... On On Flash 3s on / 1s off
Associated Ops Panel LED None None
None Logical fault (Amber) Module fault (Amber) Logical fault (Amber)
LaCie Quick Install Guide
13
Quick Install Guide - Page 15
... double beep
PCM fault LEDs, fan fault LEDs
SBB module LEDs
Aux present, overall power failed or switched off Ops panel Power On (5s) test state
Power On, all functions good Any PCM fault, fan fault, over or under temp. Any SBB module fault
LaCie Quick Install Guide
14 Front Panel LED States
Figure 11 - 4.4.
Quick Install Guide - Page 16
...) SBB module type installed, I2C bus failure (inter SBB comms) EBOD VPD configuration error
Unknown (invalid or mixed) PCM type installed, or I2C bus failure (PCM comms)
Drive failure has occurred causing loss of availability or redundancy
Arrays operating background function
Enclosure ID setting different from Start of Day
SES controlled enclosure ID
LaCie Quick Install Guide
15
Quick Install Guide - Page 17
...;re 91349 Massy Cedex, France sales.intl@lacie.com support.intl@lacie.com
Visit www.lacie.com for more information on LaCie products.
Contact Us
LaCie Asia 25/F Winsan Tower 98 Thomson Road Wanchai, Hong-Kong, China info.asia@lacie.com
LaCie Australia 458 Gardeners Road Alexandria, NSW 2015 info.au@lacie.com
LaCie Benelux Vorstlaan / 165 Bld du Souverain...
Lacie 12big Rack Serial 2 Reviews
We have not received any reviews for Lacie yet.