User Manual
Page 9
... FRUs Before replacing parts Make sure that changed the symptoms. Attention: The setup configuration on the customer support site http://www.lenovo.com/think/ support Advise customers to contact the Customer Support Center at 800-565-3344 for replacing and servicing FRUs: v If...unnecessary expense for assistance or download information. Portions © IBM Corp. 2005. 3 Introduction Important service information Important BIOS and device driver fixes are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before replacing any FRUs...
... FRUs Before replacing parts Make sure that changed the symptoms. Attention: The setup configuration on the customer support site http://www.lenovo.com/think/ support Advise customers to contact the Customer Support Center at 800-565-3344 for replacing and servicing FRUs: v If...unnecessary expense for assistance or download information. Portions © IBM Corp. 2005. 3 Introduction Important service information Important BIOS and device driver fixes are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before replacing any FRUs...
User Manual
Page 65
...This combination of Fn with another user ID, and Fn+F3 is pressed, the panel does not appear. 2. v ThinkPad Power Management driver v OnScreen Display utility v Wireless device drivers Reserved. (continued) ThinkPad R50e, R51e and R52 Series 59 Put the computer in standby mode. If the user have logged on again..., press any key or press the TrackPoint pointing stick. Product overview Fn key combinations The following drivers must be turned off the computer display, leaving the screen blank. Key combination Fn+F1 Fn+F2 Fn+F3 Fn+F4 Fn+F5 Fn...
...This combination of Fn with another user ID, and Fn+F3 is pressed, the panel does not appear. 2. v ThinkPad Power Management driver v OnScreen Display utility v Wireless device drivers Reserved. (continued) ThinkPad R50e, R51e and R52 Series 59 Put the computer in standby mode. If the user have logged on again..., press any key or press the TrackPoint pointing stick. Product overview Fn key combinations The following drivers must be turned off the computer display, leaving the screen blank. Key combination Fn+F1 Fn+F2 Fn+F3 Fn+F4 Fn+F5 Fn...
User Manual
Page 67
... button is displayed only if the ThinkPad computer has been docked in a ThinkPad Mini Dock and one or more USB devices have the PM device driver installed on the screen for the Fn+F9 function. The computer display becomes brighter. Enable the FullScreen Magnifier function. v Eject ThinkPad PC from the ThinkPad...
... button is displayed only if the ThinkPad computer has been docked in a ThinkPad Mini Dock and one or more USB devices have the PM device driver installed on the screen for the Fn+F9 function. The computer display becomes brighter. Enable the FullScreen Magnifier function. v Eject ThinkPad PC from the ThinkPad...
User Manual
Page 77
...to plastic Turn an additional 90 degrees after the screw head touches the surface of the logic card: 180 degrees more (Cross-section) v Torque driver If you have the following when you service this machine: v Keep the screw kit (for each step. Read this problem is addressed with shock... This section contains notices related to tighten. v They are harder to removing and replacing parts. v Use a torque screwdriver if you have a torque driver, refer to plastic Turn an additional 180 degrees after the screw head touches the surface of the plastic part: 90 degrees more (Cross-section) v...
...to plastic Turn an additional 90 degrees after the screw head touches the surface of the logic card: 180 degrees more (Cross-section) v Torque driver If you have the following when you service this machine: v Keep the screw kit (for each step. Read this problem is addressed with shock... This section contains notices related to tighten. v They are harder to removing and replacing parts. v Use a torque screwdriver if you have a torque driver, refer to plastic Turn an additional 180 degrees after the screw head touches the surface of the plastic part: 90 degrees more (Cross-section) v...