Service Manual
Page 38
...is Off. Photoconductor kit life warning Meaning The photoconductor is full and must be turned on in the driver for this message to appear. 4513-200, -220, -230 Toner cartridge region mismatch/Change cartridge invalid refill/Missing or defective... Action • Press and release Continue to print a photoconductor kit instruction page. • Replace the photoconductor kit. 2-12 Lexmark™ E260, E260d, E260dn Action • Press and release Continue to clear the light sequence and continue printing. • Replace the photoconductor kit. Action...
...is Off. Photoconductor kit life warning Meaning The photoconductor is full and must be turned on in the driver for this message to appear. 4513-200, -220, -230 Toner cartridge region mismatch/Change cartridge invalid refill/Missing or defective... Action • Press and release Continue to print a photoconductor kit instruction page. • Replace the photoconductor kit. 2-12 Lexmark™ E260, E260d, E260dn Action • Press and release Continue to clear the light sequence and continue printing. • Replace the photoconductor kit. Action...
Service Manual
Page 62
...wear strips and replace if necessary. Finally, check the paper size settings in the printer and the driver. 200.03 The video never started to media prestaged in the source tray. See "Diagnostics mode ... the solenoids. • Faulty/contaminated flags or springs. • Debris in the diagnostic mode for E260, E260d, and E260dn. Paper jam error codes (200-series) Error Description Action 200.00 Paper jam around input sensor. See.... Then, inspect the flag on page 4-39. 2-36 Lexmark™ E260, E260d, E260dn See "Media manual input sensor removal" on the input sensor.
...wear strips and replace if necessary. Finally, check the paper size settings in the printer and the driver. 200.03 The video never started to media prestaged in the source tray. See "Diagnostics mode ... the solenoids. • Faulty/contaminated flags or springs. • Debris in the diagnostic mode for E260, E260d, and E260dn. Paper jam error codes (200-series) Error Description Action 200.00 Paper jam around input sensor. See.... Then, inspect the flag on page 4-39. 2-36 Lexmark™ E260, E260d, E260dn See "Media manual input sensor removal" on the input sensor.
Service Manual
Page 64
... cause is that the page is that the page stalled at the alignment gate. The alignment roller may be binding. Retry alignment. 2-38 Lexmark™ E260, E260d, E260dn Check the printhead. "Printhead service check" on page 2-65. Possible cause is delayed at the alignment gate. Call the next level of ... than 14 inches too long over the manual feeder sensor. Probable causes: ESD or noise on data collection during warmup. 200.27 Printhead Driver: Mirror motor fell out of lock condition after the media at least as far as the manual feeder sensor. See "Rear exit guide ...
... cause is that the page is that the page stalled at the alignment gate. The alignment roller may be binding. Retry alignment. 2-38 Lexmark™ E260, E260d, E260dn Check the printhead. "Printhead service check" on page 2-65. Possible cause is delayed at the alignment gate. Call the next level of ... than 14 inches too long over the manual feeder sensor. Probable causes: ESD or noise on data collection during warmup. 200.27 Printhead Driver: Mirror motor fell out of lock condition after the media at least as far as the manual feeder sensor. See "Rear exit guide ...
Service Manual
Page 74
... NPA Mode Network Buffer Mac Binary PS Std Net Setup USB Menu PCL SmartSwitch PS SmartSwitch NPA Mode USB Buffer Mac Binary PS 2-48 Lexmark™ E260, E260d, E260dn 4513-200, -220, -230 Diagram of the printer menus Not all menus or selections will be available on all models or in all situations...
... NPA Mode Network Buffer Mac Binary PS Std Net Setup USB Menu PCL SmartSwitch PS SmartSwitch NPA Mode USB Buffer Mac Binary PS 2-48 Lexmark™ E260, E260d, E260dn 4513-200, -220, -230 Diagram of the printer menus Not all menus or selections will be available on all models or in all situations...
Service Manual
Page 86
A heavier media may have an unbalanced force against the PC (photoconductor) drum. Check the springs in the printer driver. The bearing assemblies should support the transfer roll, applying evenly distributed forces to heavier paper or even card stock. See"LVPS/HVPS service ...from finger oils or hand lotion. Check the media settings in the left and right transfer roll bearings. Variation in the printer driver. 2-60 Lexmark™ E260, E260d, E260dn Note: Do not touch the transfer roll except at the proper temperature to fuse the toner to make sure that the laser light...
A heavier media may have an unbalanced force against the PC (photoconductor) drum. Check the springs in the printer driver. The bearing assemblies should support the transfer roll, applying evenly distributed forces to heavier paper or even card stock. See"LVPS/HVPS service ...from finger oils or hand lotion. Check the media settings in the left and right transfer roll bearings. Variation in the printer driver. 2-60 Lexmark™ E260, E260d, E260dn Note: Do not touch the transfer roll except at the proper temperature to fuse the toner to make sure that the laser light...
Service Manual
Page 90
... Error light is on the paper feed tires for burrs or debris that the ACM clutch is selected from the printer driver. The printer does not print after picking. • Make sure the tray is pushed all the way in the ... next command. • Clear all the way in the User's Guide). • Make sure the paper guides are selected from the driver. • Make sure the tray is less than resisting force. • Remove the media from Tray 1, and fan it . .... - If a menu settings page cannot be printed, then the problem is installed properly. 2-64 Lexmark™ E260, E260d, E260dn
... Error light is on the paper feed tires for burrs or debris that the ACM clutch is selected from the printer driver. The printer does not print after picking. • Make sure the tray is pushed all the way in the ... next command. • Clear all the way in the User's Guide). • Make sure the paper guides are selected from the driver. • Make sure the tray is less than resisting force. • Remove the media from Tray 1, and fan it . .... - If a menu settings page cannot be printed, then the problem is installed properly. 2-64 Lexmark™ E260, E260d, E260dn