LiftMaster RSW12U Support and Manuals
Get Help and Manuals for this LiftMaster item
View All Support Options Below
Free LiftMaster RSW12U manuals!
Problems with LiftMaster RSW12U?
Ask a Question
Free LiftMaster RSW12U manuals!
Problems with LiftMaster RSW12U?
Ask a Question
Popular LiftMaster RSW12U Manual Pages
"Manufacturer's Certification for Credit" Manual - Page 1
... (Single gate model RSW12V) LiftMaster RSW12V Residential DC Swing Gate Operator System (Dual gate model RSW12V)
Elite RoboSlide Solar Gate Operator System (Single Gate Model RoboSL3) Elite RoboSlide Solar Gate Operator System (Dual Gate Model RoboSL3) Elite RoboSwing Solar Gate Operator System (Single Gate Model RoboSW3) Elite RoboSwing Solar Gate Operator System (Dual Gate Model RoboSW3)
Under...
RSW12U Compact Installation Manual - Page 2
... should be a maximum of 4" (10.2 cm) from the edge of the open gate to the edge of the output shaft
Install the electrical conduit. Center of gate hinge
6" Above Ground
Below the frost line.
(Gate Open 90°)
26-1/2" from the center of the gate hinge to the center of
output shaft
(conduit location)
26-1/2"
9"
28" Output...
RSW12U Installation Manual - Page 1
LiftMaster 845 Larch Avenue Elmhurst, IL 60126-1196 Model RSW12U
RESIDENTIAL DC
VEHICULAR SWING GATE OPERATOR
INSTALLATION MANUAL
• THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A TRAINED GATE SYSTEMS TECHNICIAN ONLY.
• This model is for use on vehicular passage gates ONLY and not intended for use on pedestrian passage gates.
• This model is intended for use in Class I and ...
RSW12U Installation Manual - Page 14
... temporarily hold the arm in this position. Use the set screws on the gate as shown). OPEN GATE
Gate
Open
90°
Output Shaft
2
Set
Screws
C
Output Shaft
D 12 Make sure the operator arm is E.
2. Measure both sections of the operator arm from the gate hinge center. 3. INSTALLATION
STEP 3
POSITION THE GATE BRACKET
NOTE: It may be necessary to attach...
RSW12U Installation Manual - Page 17
....
INSTALLATION
STEP 6 continued... Refer to -Close.
These entrapment protection device inputs are three options for 4 seconds then stop. This input will be disregarded during gate opening. When an obstruction is sensed Switch set to each input. This input will reverse to the full open position and resets the Timer-to the specific entrapment protection device manual for...
RSW12U Installation Manual - Page 23
... is not
set for environmental changes.
Cycle the gate open and close limit. 3. The electronic controls sense the amount of safety reversal system.
• NEVER increase force beyond minimum amount required to move gate.
• NEVER use force adjustments to
the open and close position. The limit setup LEDs (located next to the SET OPEN and SET CLOSE buttons...
RSW12U Installation Manual - Page 26
... control codes are now erased. Within 30 seconds, when the gate is successful. TO REMOVE AND ERASE MONITORED ENTRAPMENT PROTECTION DEVICES
1. Press and release the SET OPEN and SET CLOSE buttons simultaneously. Connect power to add devices. Create an online account by visiting www.myliftmaster.com.
4. The LiftMaster Internet Gateway will turn off the SET OPEN and SET CLOSE...
RSW12U Installation Manual - Page 27
... as RSW12U. See Status LED Chart in Limit setting mode. See Bipart Delay section. 6 LEARN Button: The LEARN button is restored or batteries voltage increases.
• Option select switch set to OPEN forces gate to the TTC expiring will show the operator type, firmware version, and error codes. OPERATION
CONTROL BOARD OVERVIEW
1 SET OPEN Button: The SET OPEN button sets the OPEN...
RSW12U Installation Manual - Page 33
LiftMaster System
Installed System
Informational
External Entrapment Protection
Inherent Entrapment Protection
Code 31 32 33 34 35
36
37 38 39 40
41
42
43 44 45 46 50 51 52
53
54
Meaning
Solution
Main control board has experienced an internal failure.
If so, erase limits, enter limit setup mode and set too tightly against...
RSW12U Installation Manual - Page 36
... not set to limit. Gate stops during a) Control (Open, Close) becoming active
travel and reverses b) Vehicle loop detector active
immediately. e) Check Fire Dept input
f) Check Timer-to limit. c) If on battery power only, low or dead batteries c) Charge batteries by AC or solar power or replace batteries
Gate opens, but motor does not run and error code b) Open fuse...
RSW12U Installation Manual - Page 37
... terminals).
a) Incorrect Bipart switch setting
a) Expansion board setting b) Constant pressure to stop , and may reverse direction. Check that obstructing photoelectric sensor causes moving gate to open or closed is needed
gate's path does not
cause gate to stop or reverse gate.
Alarm beeps three times with a command. b) Replace defective photoelectric sensor. a) Check...
RSW12U Installation Manual - Page 40
...Gate Open 90°
Output Shaft Center 26-1/2"
9"
28" Handle
STEP 2
CONCRETE PAD AND OPERATOR ATTACHMENT
COMPACT INSTALLATION ONLY
Check the national and local building codes before installation. 1. Install... LOCATION FOR CONCRETE PAD AND OPERATOR
COMPACT INSTALLATION ONLY
DO NOT run the operator until instructed.
TOP VIEW OF OPERATOR AND GATE
Gate Hinge Center
4" (10.2 cm) maximum...
RSW12U Installation Manual - Page 46
...
LIMIT SETUP WITH A REMOTE CONTROL
To set the limits using a remote control, first you will exit the limit setting mode after resetting each operator. Once the gate is set properly the operator will automatically exit limit setting mode. The gate can be jogged back and forth using the OPEN and CLOSE buttons on the remote control.
3. Cycle the gate open...
RSW12U Installation Manual - Page 51
... REINSTALLING A REPAIRED OR REPLACED UNIT, OR REPLACEMENT OF BATTERIES. You will be repaired or replaced with those instructions will be defective and covered by this product is free from defect in its entirety. THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GATE OR GATE HARDWARE, INCLUDING BUT NOT LIMITED TO THE GATE SPRINGS, GATE ROLLERS, GATE ALIGNMENT...
RSW12U Wiring Diagram Manual - Page 1
...
No action required
WIRING DIAGRAM
Model RSW12U
COAXIAL CABLE
ANTENNA
Control Board
CONTROLS
Jumper N.C.
If not, disconnect all power, wait 15 seconds, then
31 failure. Operator may be set limits. check for power.
CODE SEQUENCE NUMBER
The first number shown is powered. Product ID Error 36
Was the control board just replaced?
No battery at end...
LiftMaster RSW12U Reviews
We have not received any reviews for LiftMaster yet.