Mackie MDR24/96 Support and Manuals
Get Help and Manuals for this Mackie item
View All Support Options Below
Free Mackie MDR24/96 manuals!
Problems with Mackie MDR24/96?
Ask a Question
Free Mackie MDR24/96 manuals!
Problems with Mackie MDR24/96?
Ask a Question
Popular Mackie MDR24/96 Manual Pages
Operation Guide - Page 2
... has formed on the MDR24/96.
7. Clean only with only the accessories specified in a commercial installation. MDR 24/96
CAUTION AVIS
RISK OF ELECTRIC SHOCK DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL...
Operation Guide - Page 4
B 10/02 © 2002 Mackie Designs Inc. All rights reserved Printed in the U.S.A.
4
MDR 24/96 MDR 24/96
Appendix A: Troubleshooting and Service----56
Appendix B: Specifications 56
Appendix C: Upgrading the System Software- 57
Appendix D: Analog I/O Pinout 58
Appendix E: Compatible Cables 59 Analog and Digital Multitrack Cables ----59
Horizon Music, Inc 59 Hosa Technology, Inc 59 Marshall...
Operation Guide - Page 9
... using inexpensive, removable 2.2 GB ORB cartridges; At 96 kHz the drive stores 1100 track-minutes of 24-bit audio (45 minutes of hard disk recording, the Mackie Designs MDR24/96 takes multitrack recording to change routing and bussing assignments or use . Our goal was to build a hard disk recorder that doesn't require you 're not reading the wrong manual. That's more than six reels of...
Operation Guide - Page 10
... fiber optic cables, depending on the rear panel is a computer. ADAT Optical cables can reach up and configure the MDR24/96 for your console.
Powering-on . MDR 24/96
Setup and Configuration
This chapter explains how to set up to about 10 meters. If your region. Be aware that although analog and AES/EBU cables can cause...
Operation Guide - Page 14
... the MDR24/96 as a master, set the receiving device(s) to derive sample clock from their interconnecting DTRS cables. MDR 24/96
The following are using an MDR24/96 with the devices connected to the MDR24/96 digital... of the first DTRS recorder only; SYNC
Note: If you are recommended setups for establishing proper sample clock synchronization with the Mackie Digital 8•Bus console...
Operation Guide - Page 17
... to configure the MDR24/96 I /O
The SETUP TAPE INPUTS menu shows you are recorded in every sample. I /O Card Setup Stat Rate
In Out Bits Convert
(SETUP TAPE INPUTS) 1-8 9-16 17-24 ADAT ADAT ADAT
4.
matically when it at any time by pressing either the Page Left ( ) b u t t o n below
the display.
1.
Operation Guide
17
DIO•8 Card To set the DIO...
Operation Guide - Page 36
... winding speed still further.
rather, new audio files are created in a few seconds. Press a track's REC (Record Ready) button. Press it with no tracks armed (master record standby mode).
36
MDR 24/96 PLAY
RECORD
2. The Record LED glows when the MDR24/96 is recording and blinks when RECORD is engaged with magnetic tape; when pressed from stop, the "tape" rolls slowly at...
Operation Guide - Page 38
... display all the tracks are playing virtual track 4. The MDR24/96 has many features that tracks 1-4 are playing back virtual track 1, tracks 5-9 are playing virtual track 2, tracks 10-21 are playing virtual track 8, and tracks 22-24 are playing back their first virtual track.
38
MDR 24/96
It's true, but it above an ordinary 24-track recorder. These virtual tracks give you...
Operation Guide - Page 40
... for recording. Auto Input affects only tracks that it will continue all Record Ready tracks.
AUTO INPUT
40
MDR 24/96 With the Auto Take button engaged,
the next time you are recording vocals on track 12,
your first take may want to record multiple passes, each on , both armed and unarmed tracks monitor their inputs, and the Auto Input setting has...
Operation Guide - Page 42
...'t
30
-8
35
-13
40
-18
clip while the recorder is 18 dB of putting out at the later time.
By setting Loop points surrounding the Punch points, you can take advantage of the track.
Pressing the RECORD button when outside of the Punch area.
42
MDR 24/96
So, if your
dBu equivalent
OL
+22 dBu
2
+20...
Operation Guide - Page 44
... page.
3. The footswitch solos the channel displayed in the Track Number window on the MDR24/96 will output audio from only the soloed track. Press the Right Arrow button to move to choose a setting.
Press the footswitch again with audio, but not for the MDR24/96 or a Mackie Remote:
1. MDR 24/96
Solo (Remote Only): This choice is available for the...
Operation Guide - Page 49
... a History List. Press the UndoRedo select button. TRACK EDIT MENU [1]->
TRACK/ P
Undo- Operation Guide
Insert
Access the Paste command by copying the exiting ...tracks instead of all three
together. Think of the MDR24/96. When you to revert to increase the
length of them.
The MDR24/96 does not remember the History list forever. Instead of replacing existing data as a record...
Operation Guide - Page 52
... along the way you have seven good takes. To begin, press the TRACK/EDIT button, then press the Virtual Track select button. After we will place the comp on the comp track. MDR 24/96
Making a Vocal Comp
When recording vocals, it is filled with the MDR24/96 virtual tracks. When you have a take . Go to the Copy menu, select...
Operation Guide - Page 53
... T-CODE TAKE CHASE
DELETE LAST TRACK/ PROJECT BACKUP DISK UTIL SYSTEM DIGI-I/O SYNC EDIT
DEC
INC
REWIND
FAST FWD
STOP
PLAY
RECORD
project on the MDR 24/96 and then transfer the edited versions into Mackie Media Trays, then you will need to reformat the Internal drive, please contact Mackie Technical Support first. For example, the second recording pass on the MDR24/96...
Operation Guide - Page 62
... on the MDR can be , for details.
In this assigned gateway address.
There are connected to the Ethernet port on the network card installed in the address of addressing which must be anything, as long as it was just another each must have an integrated FTP client as the MDR24/96's address. At Mackie, we...
Mackie MDR24/96 Reviews
We have not received any reviews for Mackie yet.