Makita 5007NK Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita 5007NK manuals!
Problems with Makita 5007NK?
Ask a Question
Free Makita 5007NK manuals!
Problems with Makita 5007NK?
Ask a Question
Makita 5007NK Videos
HITACHI V/S MAKITA C7ST V/S 5007NK 1600 CONCEPCION
Duration: :51
Total Views: 1,266
Duration: :51
Total Views: 1,266
Popular Makita 5007NK Manual Pages
Owners Manual - Page 2
..., clothing, and gloves away from heat, oil, sharp edges or
moving parts.
2 Water entering a power tool will increase the risk of flammable liquids, gases or dust. Remove any way. This enables better control of electric shock. 5. ENGLISH (Original instructions)
SPECIFICATIONS
Model
5007N/5007NF/5007NFA
Blade diameter
185 mm (7-1/4")
at all times.
Unmodified plugs and...
Owners Manual - Page 3
... tool or these instructions to minimize body exposure...support the work to use the power tool if the switch does not turn it was designed. 18. When using an extension cord, be repaired. 19.
If devices are easier to carry the current your power tool serviced by a qualified repair person using only identical replacement parts...16
12
16
14
000300
CIRCULAR SAW SAFETY
GEB013-6
3. Such...
Owners Manual - Page 4
...saw will also make exposed metal parts of proper hand support, workpiece support, and supply cord routing (if applicable).
000157
5. Use extra caution when sawing into the material. Never use a rip fence or straight edge guide....
8. Support large panels to remove the saw backward while the blade is binding, or when interrupting a cut . Unsharpened or improperly set blades produce...
Owners Manual - Page 5
...end of the saw can lead to saw with the circular saw is released. 22...supported, not on bench or floor. Inspect for special cuts such as blade enters the material, the lower guard must be retracted manually only for and remove all nails from lumber before placing saw...setting the tool down on the section that the blade cuts without decrease in all other part, in blade ...
Owners Manual - Page 6
...replace strict adherence to safety rules for dangerous KICKBACKS which may cause serious personal injury. Gum and wood pitch hardened on the depth guide and move the base up or down.
Bevel cutting
2
3
1. Setting bevel angle Loosen the lever and tentatively set...blades recommended in this instruction manual may be sure that...on blades slows saw blade.
31.
At this manual. Do not ...
Owners Manual - Page 7
... the tool is plugged. SERIOUS PERSONAL INJURY CAN RESULT. To install hex wrench, place it on the handle and turn it ....to stop blade after switch trigger release, have tool serviced at a Makita service center. Hex wrench storage
1. Protrusion
1 2
...points 56, it can be defective. Hex wrench 2. Electric brake For model 5007NFA only This tool is not a substitute for lower guard. NOTE: ...
Owners Manual - Page 8
... on the workpiece to install or remove the
blade. Rip fence (Guide rule)
1
014099
The handy rip fence allows you to do not, however, replace the need to properly follow the removal procedure in a straight line
gently. Simply slide the rip fence up
at the front of accumulated sawdust. Saw blade
4. Set the base on...
Owners Manual - Page 9
...
For model 5007NFA only After replacing brushes, plug in the tool and break in this manual. If you need any other maintenance or adjustment should be included in the tool
package as standard accessories.
But if it is not working well, ask your Makita tool specified in brushes by Makita Authorized or Factory Service Centers, always...
Owners Manual - Page 10
..., Makita will repair (or at our option, replace) without charge. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. EN0006-1
10 MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is warranted to you . MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE...
Parts Breakdown - Page 2
... ASS'Y 115V INC. 2223252930 ARMATURE ASS'Y 115V INC. 2223252930 FAN 80 COMPRESSION SPRING 9 SHAFT LOCK FLAT WASHER 15 BALL BEARING 6002DDW URETHANE WASHER 26 BLADE CASE COMPLETE RUBBER PIN 4 Item 1 2 3 4 5 6 7 8
008-1 008-2
9 10 11 12 012-1 13 14 15 16 17 18 19 19 19 20 21 22 022-1 23 24...
Parts Breakdown - Page 3
... HEX. NUT M8-13 BOW STOP RING E-12 REAR COVER TAPPING SCREW 4X18 PAN HEAD SCREW M5X45 5007N NAME PLATE FRONT GRIP BRUSH HOLDER CAP 6.5-13.5 CARBON BRUSH CB-154 CARBON BRUSH CB-154 BOW ... M5X45 FLAT HEADSQUARE NECKBOLT M8X24 CAP SQUARE NECK BOLT M8X24 CAP SQUARE NECK BOLT M8X28 PIPE 9 DEPTH GUIDE COMPLETE CAP SQUARE NECK BOLT M8X90
#NAME? NUT M8-13 FLAT WASHER 8 ANGULAR PLATE COMPLETE ANGULAR PLATE...
Parts Breakdown - Page 4
LOCK NUT M5-8 GUIDE RULE TCT SAW BLADE 7-1/4'X24T HEX. WRENCH 6 PLASTIC CARRYING CASE LATCH HANDLE DIAL 27 STEEL BALL 4 COMPRESSION SPRING 4 COUNTERSUNK HEAD SCREW M5X12 SCREW M6X15 FLAT WASHER 5 HEX. 075-1 76 77 78 79 80 81 82 ...
Flyer (English) - Page 1
makitatools.com 7-1/4" CIRCULAR SAW
IMPROVED DESIGN FOR INCREASED PERFORMANCE • Powerful 15 AMP Motor for a High Power-To-Weight...8226; Bevel Cuts 0° - 56° With Positive Stops at 22.5°, 45° and 56° for Quick Settings
POWER
Powerful 15 AMP motor for high power-to-weight ratio
DURABILITY
Ball bearing construction engineered for a longer
tool life
PERFORMANCE
Lower ...
Flyer (English) - Page 2
... on hand. UPC code
088381-090537
Model 5007NK
0 88381 09053 7
STANDARD EQUIPMENT
n 7-1/4" carbide tipped blade - 24T (D-45989) n Blade wrench (783204-6) n Tool Case
OPTIONAL ACCESSORIES
n Carbide-tipped saw fall but
is the registered trade dress of CIRCULAR SAW accessories. All models and accessories subject to change without prior notice.
Speed: 8,300 RPM
PART NO.
24T...
Makita 5007NK Reviews
We have not received any reviews for Makita yet.