Makita 5057KB Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita 5057KB manuals!
Problems with Makita 5057KB?
Ask a Question
Free Makita 5057KB manuals!
Problems with Makita 5057KB?
Ask a Question
Popular Makita 5057KB Manual Pages
Owners Manual - Page 1
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Circular Saw with Dust Collection
185 mm (7-1/4") MODEL 5057KB
DOUBLE INSULATION
INSTRUCTION MANUAL
WARNING: For your personal safety, READ and UNDERSTAND before using. www.makitatools.com
Owners Manual - Page 2
... weight
5057KB 185 mm (7-1/4") 60 mm (2-3/8") 30 mm (1-3/16")
5,800/min. 354 mm (14") 5.3 kg (11.7 lbs)
• Manufacturer reserves the right to change specifications without notice. • Specifications may differ from country to install a polarized outlet.
GENERAL SAFETY RULES
USA002-2
(For All Tools)
WARNING: Read and understand all instructions listed below, may ignite the dust...
Owners Manual - Page 3
... on invites accidents.
12. Dust mask, non-skid safety shoes...support the workpiece to carry the tools or pull the plug from heat, oil, sharp edges or moving parts...Replace damaged cords immediately. Keep your application. Carrying tools with the switch is unstable and may result in moving parts...risk of parts, and any other condition that have the tool serviced before making...
Owners Manual - Page 4
...
Not Recommended
SPECIFIC SAFETY RULES
USB008-5
DO NOT let comfort or familiarity with the saw to jump backwards. (See "Causes and Oper- Keep your body positioned to carry the current your model. ator Prevention of the saw blade, but not in doubt, use only identical replacement parts. CAUTION: Blades coast after turn off. 22. Follow instructions in...
Owners Manual - Page 5
...guide. If the blade becomes twisted or misaligned in the material until the blade comes to damaged parts, gummy deposits, or a buildup of the lower guard spring. Do not operate saw... lower guard must be retracted manually only for any reason, release...other sawing, the lower guard should be serviced before placing saw ... is important to support the work or pull the saw to walk backwards...
Owners Manual - Page 6
...the workpiece, the saw can cause KICKBACK. Inspect for kickback. Large panels tend to maintain smooth advancement of accuracy, and possible kickback. sharp and clean. Fig. 2 Do not support board or panel away...speed of blade pinching and kickback.
Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK. To minimize the risk ...
Owners Manual - Page 7
...operation. Follow material supplier safety data. 15. Operate with the circular saw held upside down . Fig. 4 illustrates typical hand support of a board, and Fig. 6 the WRONG way. As...part of control which is made. When operating the saw base on that it down in a vise. Place the wider portion of proper hand support, workpiece support, and supply cord routing.
16. Before setting...
Owners Manual - Page 10
... Makita vacuum cleaner. Position of blade edge when depth of the tool down to collect dust and cut is equipped with the dust box to empty the dust box. Remove the rubber cap from the dust ... tool base
The right side of cut is set at the deepest position. To start the tool, simply pull the switch trigger. Lever
001392 Dust collection
This tool is set at the deepest position
1
2 3
1....
Owners Manual - Page 11
... bolt, outer flange and blade.
2 1
1. Shaft lock
1
2
4 3 1. Saw blade 2.
Such efforts do not, however, replace the need to check lower guard operation before each use 001422 the wrench to install or remove the blade. Screws
001413 Removing or installing saw blade
1
CAUTION:
• Be sure the blade is installed with teeth pointing up at the front...
Owners Manual - Page 12
...and then withdraw tool. Set the base on the... manually only for special cuts such as you start cut by Retracting Lever. Realign tool on and wait until the sawing ...or force the tool back to chips and wood dust being ejected from saw , they cannot be kept free and in ...
2
Hold the tool firmly. Rip fence (Guide rule)
001485 Rip fence (Guide rule)
The handy rip fence allows you start...
Owners Manual - Page 14
... for
use with your local Makita service center.
• For fiber-cement board saw blades
Carbide-tipped Diamond-tipped
Specifically designed to persons. Only use of injury to professionally cut fiber-cement siding, roofing and backerboard while lasting 400% longer than others.
• Rip fence (Guide rule) • Wrench 13
14 Replace when they wear down...
Owners Manual - Page 18
... PORTION
Your answers to the following questions are : Design Features Size Price Makita Brand
Repair Service
Durability
Power
Other (
)
5. Use of the product is intended for:...714) 522-8133
Paste
Paste
Paste
Paste
Paste
Paste
Paste
Paste
Paste
Paste
Paste
Paste INTL. Any comments:
Paste
Paste
Paste
Paste
Paste
Paste
Paste
Paste
DATE PURCHASED
MONTH
DAY
YEAR
MODEL...
Owners Manual - Page 19
...service: Send complete tool (prepaid) to one of the Makita Factory Service Centers listed, or to the outside of the carton detailing the problem with your tool. FACTORY SERVICE CENTERS
1-800-4-MAKITA... 3375 S. Date Purchased Dealer's Name & Address
Model No. Suile 170 Nashville, TN 372 (615)... Elm Hill P. La Mirada, CA 90638-5753 (714) 522-8088
1970 Fulton Avenue Sacramento, CA 95825...
Owners Manual - Page 20
...Makita tool is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge. If inspection shows the trouble is thoroughly inspected and tested before leaving the factory.
This Warranty does not apply where: • repairs...you specific legal rights, and you .
Makita Corporation of work with approved safety equipment, such as those dust ...
Parts Breakdown - Page 3
... GUIDE, 5057KB BASE, 5057KB SCREW M5X12,5037NB-T2 H.S.H. SCREW M5X12,2012NB
C.S.H. WASHER 8, 5057KB SCREW M6X15, 5037NB ANGULAR PLATE, 5057KB HEX. SCREW M4X8, 5037NB TAPPING SCREW 4X18, 4323K DUST BOX L COMPLETE, 5057KB DUST BOX L COMPLETE, 5057KB DUST BOX L CPL., 5057KB DUST BOX L CPL., 5057KB EARTH PLATE, 5057KB DUST CAP COMPLETE,5057KB CAP, 5044KB DUST BOX R SET, 5057KB DUST BOX R SET, 5057KB...
Makita 5057KB Reviews
We have not received any reviews for Makita yet.