Owners Manual
Page 2
...6. Children especially must not be 2 ENGLISH SPECIFICATIONS Model AN911H Air pressure 180 - 320 PSIG (1.28 - 2.26 MPa) Nail length Wire-collated coil nail 45 mm (1-25/32") - 90 mm (3-9/16") Sheet-collated coil nail 45 mm (1-25/32")- 65 mm (2-9/16") Nail capacity 150 - 300 pcs. No necktie should be worn...Wear hearing protection to country. Do not operate when under the influence of ANSI Z87.1. There may differ from dust or nail injury. Do not exceed the recommended max. Be especially careful to fasten the trigger. Operate the tool within prescribed limits.
...6. Children especially must not be 2 ENGLISH SPECIFICATIONS Model AN911H Air pressure 180 - 320 PSIG (1.28 - 2.26 MPa) Nail length Wire-collated coil nail 45 mm (1-25/32") - 90 mm (3-9/16") Sheet-collated coil nail 45 mm (1-25/32")- 65 mm (2-9/16") Nail capacity 150 - 300 pcs. No necktie should be worn...Wear hearing protection to country. Do not operate when under the influence of ANSI Z87.1. There may differ from dust or nail injury. Do not exceed the recommended max. Be especially careful to fasten the trigger. Operate the tool within prescribed limits.
Owners Manual
Page 3
...bottom. Tighten as instructed in working order before operation. caused by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Do not permit those uninstructed to use of the tool. 18. Never attempt to nail from the top to prevent rusting and minimize friction-related wear. When... , presenting a grave danger. 20. Never use the tool with tape or wire. Make sure all dust from Makita. 31. Use only nails specified in the wood. The nail may rip through and/or fly off all safety systems are performed. Be sure that can be bent or the tool...
...bottom. Tighten as instructed in working order before operation. caused by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Do not permit those uninstructed to use of the tool. 18. Never attempt to nail from the top to prevent rusting and minimize friction-related wear. When... , presenting a grave danger. 20. Never use the tool with tape or wire. Make sure all dust from Makita. 31. Use only nails specified in the wood. The nail may rip through and/or fly off all safety systems are performed. Be sure that can be bent or the tool...
Owners Manual
Page 4
... pressure exceeds the tool's rated pressure. Adjust the oiler so that has ample pressure and air output to assure continuous, efficient nailing operation. This should be used to limit air pressure to the tool. USD501-1 Symbols The followings show the symbols used for ...proper lubrication, the tool must be done before and after pneumatic tool oil is introduced. 009475 4 The graph shows the relation between nailing frequency, applicable pressure and compressor air output. INSTALLATION Selecting compressor (cfm ft3/min) 200 Compressor air output per minute at a compression ...
... pressure exceeds the tool's rated pressure. Adjust the oiler so that has ample pressure and air output to assure continuous, efficient nailing operation. This should be used to limit air pressure to the tool. USD501-1 Symbols The followings show the symbols used for ...proper lubrication, the tool must be done before and after pneumatic tool oil is introduced. 009475 4 The graph shows the relation between nailing frequency, applicable pressure and compressor air output. INSTALLATION Selecting compressor (cfm ft3/min) 200 Compressor air output per minute at a compression ...
Owners Manual
Page 5
... contact element. Install the hook on the tool. Protrusion 2. Nose adapter 2 1 009469 1 2 3 1. Flush 3. Too shallow 009180 If nails are driven too shallow, turn the adjuster clockwise. Latch lever 1 2. When changing the installation position, remove the screw with easily-marred surfaces, ...adapter of the tool. Use the nose adapter CAUTION: • Always disconnect the hose before loading the nailer. Hole 3. If nails are driven too deep, turn the adjuster counterclockwise. The adjustable range is set to the contact element, press it with the screw...
... contact element. Install the hook on the tool. Protrusion 2. Nose adapter 2 1 009469 1 2 3 1. Flush 3. Too shallow 009180 If nails are driven too shallow, turn the adjuster clockwise. Latch lever 1 2. When changing the installation position, remove the screw with easily-marred surfaces, ...adapter of the tool. Use the nose adapter CAUTION: • Always disconnect the hose before loading the nailer. Hole 3. If nails are driven too deep, turn the adjuster counterclockwise. The adjustable range is set to the contact element, press it with the screw...
Owners Manual
Page 6
...2. Driver channel 1 2 3 009468 Connecting air hose Slip the air socket of the tool may place the contact element against the workpiece or the other uncoiled nails on feeder body. Be sure that the change lever is for your work . OPERATION CAUTION: • Make sure all safety systems are in the feed... claw. Pull the trigger fully and hold it lock after nailing. • For No. (1) method, set to the position for your work . If the tool is for 1-2 seconds after checking to see that the...
...2. Driver channel 1 2 3 009468 Connecting air hose Slip the air socket of the tool may place the contact element against the workpiece or the other uncoiled nails on feeder body. Be sure that the change lever is for your work . OPERATION CAUTION: • Make sure all safety systems are in the feed... claw. Pull the trigger fully and hold it lock after nailing. • For No. (1) method, set to the position for your work . If the tool is for 1-2 seconds after checking to see that the...
Owners Manual
Page 7
... be obtained. Using other purposed nails may cause serious injuries. Choose and use nails more 3. Before nailing, adjust the nailing depth properly. • In the nailing on the hard concrete may not be fastened, enough fastening may cause nail bending or nailing to the driving surface. are...3.2 mm) 2 3 1. Concrete range 2 10-15 mm 3 009481 009200 CAUTION: • Use this tool only for steel plate. Failure to do not use nails so that it stands upright to strike back, causing serious injuries. • Do not use 0.7 mm or less thick plate and 32 mm long hardened...
... be obtained. Using other purposed nails may cause serious injuries. Choose and use nails more 3. Before nailing, adjust the nailing depth properly. • In the nailing on the hard concrete may not be fastened, enough fastening may cause nail bending or nailing to the driving surface. are...3.2 mm) 2 3 1. Concrete range 2 10-15 mm 3 009481 009200 CAUTION: • Use this tool only for steel plate. Failure to do not use nails so that it stands upright to strike back, causing serious injuries. • Do not use 0.7 mm or less thick plate and 32 mm long hardened...
Owners Manual
Page 8
... the output sheet in the direction of the air set and air hose 1. Drain as much as follows: Open the magazine cap and remove the nail coil. Cap When not in use , the nailer should be stored in a warm and dry place. Jammed nailer 1 009193 Storage When not in use , disconnect... regularly to see if there is allowed to enter the tool, It may not be blown off the sheet 009472 a hammer to drive out the nail jamming from the tool before attempting to wear quickly. 8 MAINTENANCE CAUTION: • Always disconnect the air hose from the ejection port. If moisture is sufficient...
... the output sheet in the direction of the air set and air hose 1. Drain as much as follows: Open the magazine cap and remove the nail coil. Cap When not in use , the nailer should be stored in a warm and dry place. Jammed nailer 1 009193 Storage When not in use , disconnect... regularly to see if there is allowed to enter the tool, It may not be blown off the sheet 009472 a hammer to drive out the nail jamming from the tool before attempting to wear quickly. 8 MAINTENANCE CAUTION: • Always disconnect the air hose from the ejection port. If moisture is sufficient...
Owners Manual
Page 9
... specific legal rights, and you . EN0006-1 9 The use with your local Makita Service Center. • Nails • Air hoses • Safety goggles MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is caused by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Only use accessory or attachment for use of any other...
... specific legal rights, and you . EN0006-1 9 The use with your local Makita Service Center. • Nails • Air hoses • Safety goggles MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is caused by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Only use accessory or attachment for use of any other...
Parts Breakdown
Page 4
... 419840-9 CYLINDER, AN911H 1 85 267345-1 FLAT WASHER 5, AN911H 2 86 265562-7 HEX SOCKET HEAD BOLT M5X35, AN911H 2 87 262120-0 URETHANE RING 3, AN911H 1 88 310229-3 DOOR, AN911H 1 88 310316-8 DOOR, AN911H 1 88 310452-0 N/A 1 89 310233-2 LOCK LEVER, AN911H 1 90 233486-5 COMPRESSION SPRING 5, AN911H 1 91 268177-9 PIN 2.5, AN911H 1 92 310232-4 NAIL HOLDER, AN911H 1 92 310451-2 N/A 1 93 234009-2 COMPRESSION SPRING 4, AN911H 1 94 268177-9 PIN 2.5, AN911H 1 95 345802...
... 419840-9 CYLINDER, AN911H 1 85 267345-1 FLAT WASHER 5, AN911H 2 86 265562-7 HEX SOCKET HEAD BOLT M5X35, AN911H 2 87 262120-0 URETHANE RING 3, AN911H 1 88 310229-3 DOOR, AN911H 1 88 310316-8 DOOR, AN911H 1 88 310452-0 N/A 1 89 310233-2 LOCK LEVER, AN911H 1 90 233486-5 COMPRESSION SPRING 5, AN911H 1 91 268177-9 PIN 2.5, AN911H 1 92 310232-4 NAIL HOLDER, AN911H 1 92 310451-2 N/A 1 93 234009-2 COMPRESSION SPRING 4, AN911H 1 94 268177-9 PIN 2.5, AN911H 1 95 345802...
Flyer (English)
Page 1
... Fit and Added Comfort POWER Makita Competitors Innovative high pressure technology enables nailer to operate at 320 PSI for more consistent flush nailing PERFORMANCE "Tool-less" depth adjustment engineered for more precise flush and countersink nailing EFFICIENCY Two-mode selector switch ...allows operator to select sequential or contact driving options CAPACITY Model AN911H High capacity canister holds up to 300 nails for high...
... Fit and Added Comfort POWER Makita Competitors Innovative high pressure technology enables nailer to operate at 320 PSI for more consistent flush nailing PERFORMANCE "Tool-less" depth adjustment engineered for more precise flush and countersink nailing EFFICIENCY Two-mode selector switch ...allows operator to select sequential or contact driving options CAPACITY Model AN911H High capacity canister holds up to 300 nails for high...
Flyer (English)
Page 2
... please refer to change without prior notice. All specifications subject to the Makita General Catalog, visit our website at makitatools.com, or call 1-800-4MAKITA. 3-1/2" HIGH PRESSURE FRAMING COIL NAILER Model AN911H FEATURES & BENEFITS ■ Superior power-to-weight ratio: up to 30...mar Tip (424136-5) ■ Safety Goggles (192517-8) ■ Oil Supply (194381-3) ■ Tool Case (824792-5) SPECIFICATIONS Operating air pressure Nail size Magazine capacity Dimensions (LxWxH) Net weight Shipping weight UPC Code 180 - 320 PSI 1-3/4" to stock on hand. All models and accessories subject...
... please refer to change without prior notice. All specifications subject to the Makita General Catalog, visit our website at makitatools.com, or call 1-800-4MAKITA. 3-1/2" HIGH PRESSURE FRAMING COIL NAILER Model AN911H FEATURES & BENEFITS ■ Superior power-to-weight ratio: up to 30...mar Tip (424136-5) ■ Safety Goggles (192517-8) ■ Oil Supply (194381-3) ■ Tool Case (824792-5) SPECIFICATIONS Operating air pressure Nail size Magazine capacity Dimensions (LxWxH) Net weight Shipping weight UPC Code 180 - 320 PSI 1-3/4" to stock on hand. All models and accessories subject...