Makita AN911H Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita AN911H manuals!
Problems with Makita AN911H?
Ask a Question
Free Makita AN911H manuals!
Problems with Makita AN911H?
Ask a Question
Popular Makita AN911H Manual Pages
Owners Manual - Page 2
... especially must be kept on the tool label for safety and longer tool life. There may differ from dust or nail injury. Operate the tool within prescribed limits. The tool should be clear and litter-free. ENGLISH
SPECIFICATIONS
Model
AN911H
Air pressure
180 - 320 PSIG (1.28 - 2.26 MPa)
Nail length
Wire-collated coil nail 45 mm (1-25/32") - 90 mm...
Owners Manual - Page 3
... at the same time. Keep the tool in the
vicinity. Ask Makita's Authorized service centers for this instruction manual may occur. 32. connected to avoid possible electrical shock, gas leakage, explosions, etc. Nails may cause malfunction of the ordinary with the tool. The tool must work only when both the inside the tool that dust, sand, chips and foreign...
Owners Manual - Page 4
...accidental firing.
For proper lubrication, the tool must be provided for every 30 nails. This should be used to limit ...tool labels and manual. ･ Operators and others in work area must wear safety glasses with an air output over 70 liters/minute is required. Failure to do so may cause a decrease in the vicinity. Lubrication
004295
To insure maximum performance, install an air set...
Owners Manual - Page 5
...Adjuster
The hook is set to the contact element, press it with the screw. Install the hook on another side for used nails.
1. Nose adapter
2 1
009469
1
2
3
1. Too shallow
009180
If nails are driven too shallow... hanging the tool temporarily. Flush
3. Loading the nailer
CAUTION: • Make sure that the coil support plate is convenient for installation and then secure...
Owners Manual - Page 6
.... (2) method, set to the "Intermittent
Nailing" mode, WITH THE TRIGGER HELD IN A HALF-PULLED POSITION, an unexpected nailing could occur, if contact element is for intermittent nailing, when you may result.
1. Disconnect the air hose from the tool. Lift and turn the coil support plate so that the air socket locks firmly into position when installed onto...
Owners Manual - Page 7
... may cause nail bending or nailing to the driving surface. Slanted nailing may cause nails to the concrete.
Wood thickness
3. Slanted nailing may cause concrete fragments to fly off or nails to the driving surface. When it is worn, sharpen it or replace it stands upright to strike back, causing serious injuries. • When nailing, hold the tool so...
Owners Manual - Page 8
... of the arrow when using an air duster. Tear off by using the sheet collated nails. Maintenance of the air set and air hose
1. If moisture is sufficient pneumatic oil in the direction of tool Iron dust that adhere to the floor. • When the penetration amount into the ejection port and tap...
Owners Manual - Page 9
... by others: repairs are
recommended for use accessory or attachment for the period of ONE YEAR from obstacles which may also have been made or attempted by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
1.
THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. If inspection shows the trouble is warranted...
Parts Breakdown - Page 1
Parts Breakdown
AN911H
Page 1 of 5
8/18/2010
Parts Breakdown - Page 2
Parts Breakdown
AN911H
Page 2 of 5
8/18/2010
Parts Breakdown - Page 3
... O-RING26, AN911H DRIVER, AN911H VALVE SEAT, AN911H CYLINDER STAY, AN911H CYLINDER, AN911H O RING 53, AN901 O-RING 39, AN911H TOP CAPGASKET, AN911H O-RING 6, AN911H NAME PLATE, AN911H AIR LEAK REPAIR SET, AN911H MAKITA LOGO LABEL L, AN911H MAKITA LOGO LABEL R, AN911H HOUSING SET, AN911H CYLINDER GUIDE, AN911H FRONT CUSHION, AN911H O RING, HR2511 O RING 4, AF501 DRIVER GUIDE, AN911H N/A
HEX SOCKET...
Parts Breakdown - Page 4
... VALVE GUIDE, AN911H
1
104
213968-3
O-RING 7, AN911H
2
105
419958-6
PILOT VALVE, AN911H
1
106
213185-5
O-RING 12.5, AN911H
1
107
234014-9
COMPRESSION SPRING 3, AN911H
1
107
234187-8
N/A
1
108
213034-6
O RING 3, AF502
1
109
324743-3
TRIGGER VALVE STEM, AN911H
1
110
213979-8
O-RING 3, AN911H
2
111
213275-4
O RING 18, BFL400FZ
1
112
194737-0
AIR LEAK REPAIR SET...
Parts Breakdown - Page 5
... AN911H TRIGGER ASS'Y, AN911H CHANGE ROD, AN911H COMPRESSION SPRING 6, AN911H UPPER YOKE, AN911H ADJUSTER SHAFT, AN911H COMPRESSION SPRING 2, AN911H STEEL BALL 2.3, AN911H ADJUSTER CPL., AN911H SPRING PIN 2-14, AN611 SPRING PIN 2-14, AN611 ADJUSTER PIECE, AN911H SLIDE PLATE, AN911H ADJUSTER ASS'Y, AN911H NOSE ADAPTER, AN911H SAFETY GOGGLE, AN611 N/A
OIL SUPPLY SET, AN911H PLASTIC TOOL CASE, AN911H...
Flyer (English) - Page 1
... and Added Comfort
POWER
Makita
Competitors Innovative high pressure technology enables nailer to operate at 320 PSI
for more consistent flush nailing
PERFORMANCE
"Tool-less" depth adjustment engineered for more precise flush and
countersink nailing
EFFICIENCY
Two-mode selector switch allows operator to select sequential or
contact driving options
CAPACITY
Model AN911H
High capacity canister...
Flyer (English) - Page 2
... specifications subject to the Makita General Catalog, visit our website at makitatools.com, or call 1-800-4MAKITA. For a complete listing, please refer to change without prior notice. 3-1/2" HIGH PRESSURE FRAMING COIL NAILER
Model AN911H
FEATURES & BENEFITS
■ Superior power-to-weight ratio: up to 30% less weight and up to 30% smaller than conventional framing nailers
■ "Tool...
Makita AN911H Reviews
We have not received any reviews for Makita yet.