Makita AN930H Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita AN930H manuals!
Problems with Makita AN930H?
Ask a Question
Free Makita AN930H manuals!
Problems with Makita AN930H?
Ask a Question
Popular Makita AN930H Manual Pages
Owners Manual - Page 2
...etc.; Do not operate when under the influence of the tool, read this instruction manual carefully before using the tool.
2. There may differ from dust or nail ... improperly functioning tool must be sufficiently illuminated to fasten the trigger. ENGLISH (Original instructions)
SPECIFICATIONS
Model Air pressure
AN930H 170 - 320 PSIG (1.18 - 2.26 MPa)
Nail length
Wire-collated coil...
Owners Manual - Page 3
...setting.
24. Lubricate moving the tool to keep the trigger or contact element depressed with the tool.
28. Do not attempt to a new location.
29. SAVE THESE INSTRUCTIONS... for this instruction manual may rip through...by Makita Authorized or Factory Service Centers, always using Makita replacement parts....SAFETY and RELIABILITY, maintenance and repairs should not be performed by ...
Owners Manual - Page 4
Thus, for tool. ･ Read and understand tool labels and manual. ･ Operators and others in work area must be fired a couple...safety glasses with side shields. ･ Keep fingers away from trigger when not driving fasteners to avoid accidental firing. INSTALLATION
Selecting compressor
(cfm ft3/min)
Compressor air output per minute at a compression of ANSI B19.3. CAUTION: •...
Owners Manual - Page 5
...
removing the nose adapter. Furthermore, this hook can be turned by hand to the proper depth.
1
2
3
1. Nose adapter 1 2
009180
The adjustable range is convenient for installation and then secure it onto the contact element until the protrusion in
two places inside the nose adapter fit in two holes in the direction...
Owners Manual - Page 6
... nailing
2. Turn the lock lever to reach the nail guide. Turn the hinged part inward the trigger, and then set properly in the feed claw. Loading the nailer
CAUTION: • Make sure that the arrow with nails before replacing the trigger. • After the trigger replacement, always check the
tool operates properly before actual work...
Owners Manual - Page 7
...LOCK position. • Make sure that the trigger is locked when the
change lever is set back to the LOCK position. Workpiece
2 3
013441
− The tool must not operate... operate only by pulling the trigger.
1
1.
Trigger 2. Workpiece
2
3
013537
1. NOTE: To set to continuous nailing, follow the procedures for changing the trigger above. Place the
contact element
against
2...
Owners Manual - Page 8
...CAUTION: • However when the tool is worn, sharpen it or replace it stands upright to wear. Do not place the contact element against ... not use the tool for C-shaped one . When it is set up
8 Using other surface under the influence of
all workpiece to... surface. Do not nail directly on the steel plate, the driver may cause nails to strike back, causing serious injuries. •...
Owners Manual - Page 10
... "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY. Some states do not allow limitation on during this manual. Drain cock
004317
When not in this one of original purchase. Hoses must also be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. The use with your local Makita Service Center. •...
Parts Breakdown - Page 3
...1
O RING 56
1
AIR LEAK REPAIR SET
1
INC. 7-9126
0
O-RING 28
1
DRIVER ASSEMBLY
1
INC. 11
0
HEAD VALVE GUIDE
1
O RING 71
1
VALVE SEAT
1
CYLINDER STAY
1
CYLINDER
1
O RING 56
1
O RING 42
1
TOP CAP GASKET
1
MAKITA LOGO LABEL R
1
MAKITA LOGO LABEL L
1
HOUSING SET
1
INC. 2122
0
FRONT CUSHION
1
O RING 45
1
O-RING 6
1
DRIVER GUIDE COMPLETE
1
HEX SOCKET HEAD BOLT...
Parts Breakdown - Page 4
...141980-2
MAGAZINE COMPLETE
1
42 810469-8
CAUTION LABEL
1
43 256773-5
PIN 4
1
44 233505-7
TORSION SPRING 7
1
45 259042-3
STOP RING E-3
1
46 140910-0
MAGAZINE CAP COMPLETE
1
46 892599-7
AN930H MAGAZINE LABEL
1
47 268168-0
PIN 3
1
48 419858-0
ADJUST SHAFT
1
048-1 454691-3
ADJUST SHAFT
1
49 961105-0
RETAINING RING S-25
1
50 268272-5
PIN 2.5
1
51 216008-6
STEEL BALL...
Parts Breakdown - Page 5
... 14
1
92 345781-2
CUP WASHER
1
93 962103-7
RETAINING RING R-24
1
94 262054-7
URETHANE RING 3
1
95 234208-6
COMPRESSION SPRING 6
1
96 262162-4
URETHANE RING 5
2
97 310468-5
NAIL GUIDE
1
98 268261-0
FLAT FILLISTER PIN 5
1
99 234009-2
COMPRESSION SPRING 4
1
100 310444-9
NAIL HOLDER
1
101 310465-1
DOOR
1
102 268274-1
PIN 3
1
103 231401-3
COMPRESSION SPRING 7
1
Parts Breakdown - Page 6
... 213968-3
O-RING 7
2
122 213185-5
O-RING 12.5
1
123 213044-3
O RING 3
1
124 213640-7
O-RING 3
2
125 213275-4
O RING 18
1
126 195480-4
AIR LEAK REPAIR SET
1
126
INC. 10119-125
0
127 419841-7
TRIGGER VALVE GUIDE
1
128 451958-0
PILOT VALVE
1
129 234188-6
COMPRESSION SPRING 3
1
130 325929-2
TRIGGER VALVE STEM
1
131 331741-0
TRIGGER VALVE CASE
1
132 310502-1
IDLER...
Parts Breakdown - Page 7
A05 824947-2
PLASTIC CASE
1
A05 162315-4
LATCH
2
A05-1 821594-0
PLASTIC CARRYING CASE
1
A05-1 162315-4
LATCH
2
A06 892597-1
AN930H PLASTIC CASE LABEL
2
A07 123204-8
TRIGGER ASSEMBLY
1
A07 233570-6
TORSION SPRING 3
1
A07 310434-2
TRIGGER
1
A07 310503-9
IDLER C
1
A07 951007-8
SPRING PIN 2-12
1
Flyer (English) - Page 1
makitatools.com
3½" High Pressure Framing Coil Nailer
Model AN930H
SUPERIOR POWER-TO-WEIGHT RATIO: UP TO 30% LESS WEIGHT (5.7 LBS.) AND UP TO ...at 170-320 PSI for
more consistent flush nailing
ERGONOMICS
21-13/165" (length) Hitachi* NR83A2
11-1/4" (length) Makita AN930H
Up to 30%less weight (5.7lbs.) and up to 30%smaller than conventional framing nailers
PERFORMANCE
"Tool-less"depth ...
Flyer (English) - Page 2
... accessories subject to change without prior notice. The Makita Teal Color is the trade dress of accessories. All specifications subject to stock on hand. 3½" High Pressure Framing Coil Nailer
Model AN930H
FEATURES &BENEFITS
n Superior power-to-weight ratio: up to 30% less weight (5.7 lbs.) and up to 30% smaller than conventional framing nailers...
Makita AN930H Reviews
We have not received any reviews for Makita yet.