Makita AT638A Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita AT638A manuals!
Problems with Makita AT638A?
Ask a Question
Free Makita AT638A manuals!
Problems with Makita AT638A?
Ask a Question
Popular Makita AT638A Manual Pages
AT638A Instruction Manual - Page 2
ENGLISH (Original instructions)
SPECIFICATIONS
Model: Air pressure Staple length Staple capacity Minimum hose diameter Dimensions (L x W x H)
AT638A 0.49 - 0.83 MPa (70 - 120 PSIG)
13 mm (1/2″)...compressed air. The tool should not be modified unless authorized in the tool manual or approved in the instruction manual. Never use a tool with fasteners unloaded and the contact element in ...
AT638A Instruction Manual - Page 3
... than that is high pressure inside the tool, failure to the fastener application and the training of injury always manage recoil by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
ENGLISH Do not drive fasteners into existing walls or other fasteners.
14. Do not load tool with a finger on the trigger. Do...
AT638A Instruction Manual - Page 4
...instruction manual may cause serious personal injury.
Trigger 2. Stapling frequency (times/min) 2. Thus, for tool.
2.5
Read and understand tool labels and manual. Selecting air hose
CAUTION: Low air output of the compressor, or a long or smaller diameter air hose in relation
to the stapling...
0.5
PARTS DESCRIPTION
2
1
4 3
► 1 . Symbols
INSTALLATION
Selecting ...
AT638A Instruction Manual - Page 5
...3 (three) drops into the air fitting. Generally speaking, the tool service life will be fired a couple of staple driving. CAUTION: Do not hang the hook from the tool. Lubrication
... (6.6 ft.) is recommended when the interval between each stapling is 0.5 seconds. The depth of stapling
1 B A
To insure maximum performance, install an air set (oiler, regulator, air filter) as close as possible ...
AT638A Instruction Manual - Page 6
... using the air duster.
CAUTION: Load the same type, size and uniform length of staples when loading multiple strips of workpiece from being scratched or damaged, use the air duster...grip end.
1
2
1 ► 1 . The oil may cause a personal injury. Removing staples
To remove staples, follow the procedures of the magazine.
Press the lever and open the sliding door of "Loading ...
AT638A Instruction Manual - Page 7
... sequential operation. After stapling, release the contact element, and then release the trigger.
2 1
7 ENGLISH Spare nose adapter
Connecting air hose
1
2
► 1 . A hose coupling must be installed on the stapler. Air fitting 2. Single sequential actuation
Place the contact element against the workpiece and pull the trigger fully. Select this mode, set the actuation mode...
AT638A Instruction Manual - Page 8
... fully and hold the rear of the sliding door when you press the lever. Reload the staples when the empty indicator becomes red. Follow the procedure of "Removing staples" to remove the strip of compressor, air set and air hose
After operation, always drain the compressor tank and the air filter. NOTICE: Never...
AT638A Instruction Manual - Page 9
...• repairs are recommended for the period of ONE YEAR from workmanship and materials for use with your local Makita Service Center.
• Staples
•...Makita Authorized or Factory Service Centers, always using Makita replacement parts.
Also, route the hose away from obstacles which may differ from chemicals (thinner, strong acids or alkalis). If inspection shows the trouble...
AT638A Parts Breakdown - Page 1
1 2 3
5 4
6 7
8 9 10 11 12 13 14 15
16
17
18
19 20
21
22 24
23 A
27
29 28
25 26
30
32
33
34 31
35 36 37 38
39 40
41
45
A
44
43 42
AT638A 9-16
AT638A Parts Breakdown - Page 3
Model AT638A Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part...CYLINDER SEPARATER O-RING 46 CYLINDER O-RING 31 O RING 30.5 O RING 22.5 DRIVER BLADE ASSEMBLY FRONT BUMPER HOUSING ASSEMBLY INC. 25-29 HOUSING BUMPER R HOUSING BUMPER... AIR DUSTER ASSEMBLY INC. 32-45 DUSTER BUTTON PIN 2 COMPRESSION SPRING 5 VALVE GUIDE O RING 8.5 O RING 5 VALVE STEM O-RING 3 ONE TOUCH JOINT SPRING ...
AT638A Parts Breakdown - Page 4
... SPRING 5 LEVER O-RING 3 MAIN MAGAZINE PIN 4 HOOK HEX. SOCKET HEAD BOLT M4X12 DRIVER GUIDE PIN 2 CAUTION LABEL NOSE NO MAR TIP HEX. 049
HY00000436
050
HY00000437
051
HY00000053
052... IDLER SPRING PIN 2.5-16 STEEL BALL 3 COMPRESSION SPRING 2 LEVER 4 RUBBER RING 8 TRIGGER VALVE GUIDE COMPRESSION SPRING 4 TRIGGER VALVE STEM O-RING 3 TRIGGER VALVE CASE O-RING 11 COMPRESSION SPRING 10 HOLDER...
Makita AT638A New Tool Flyers English - Page 1
...HY00000378) n Tool Case
All specifications subject to change without prior notice. Patent and Trademark Office
Makita offers a wide variety of Makita Corporation and is protected under common...staples n Housing bumpers protect tool and work surface n Aluminum body for durability with the U.S. The Makita Teal Color is the trade dress of accessories. 1/4" Narrow Crown Stapler, 18 Ga. Model AT638A...
Makita AT638A Reviews
We have not received any reviews for Makita yet.