Makita CC02Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita CC02Z manuals!
Problems with Makita CC02Z?
Ask a Question
Free Makita CC02Z manuals!
Problems with Makita CC02Z?
Ask a Question
Popular Makita CC02Z Manual Pages
CC02 Instruction Manual - Page 2
... injury.
2 ENGLISH Ensure the switch is unavoidable, use . ENGLISH (Original instructions)
SPECIFICATIONS
Model: Diamond wheel diameter Max.
Work area safety 1. Do not operate power tools in a damp... location is in the warnings refers to a rotating part of electric shock.
4. There is earthed or grounded.
3. Always wear eye protection. ...
CC02 Instruction Manual - Page 3
...serviced by various operations.
Store idle power tools out of the reach of stopping flying debris generated by a qualified repair person using only identical replacement parts...with specifically ... instructions...and installing the...support the wheel thus reducing the possibility of the rotating wheel and run out of balance, vibrate excessively and may cause irritation or burns.
3
Service...
CC02 Instruction Manual - Page 4
...stop . Supports must be pulled into existing walls or other blind areas. Before using a segmented diamond wheel, make exposed metal parts of ...replace strict adherence to climb out or kick out. Overstressing the wheel increases the loading and susceptibility to high intensity noise may damage the wheels. Prolonged exposure to twisting or binding of the wheel in this instruction manual...
CC02 Instruction Manual - Page 5
...Do not use genuine Makita batteries. For preparation of the battery cartridge. Tape or mask off your eyesight. 5. Overcharging shortens the battery service life.
3. Installing or removing battery cartridge
... cartridge cool down before completely discharged. Before using battery cartridge, read all instructions and cautionary markings on the front of your hands and result in the ...
CC02 Instruction Manual - Page 6
... groove in place with "B" at the end of the model number
Indicator lamps
Lighted
Off
Remaining capacity
75% to 100...stops soon. Depth guide
Loosen the clamping screw on the battery cartridge to become overloaded. To install the battery cartridge...► 1 . In this situation, remove and recharge the battery. Set for the desired angle (0° - 45°) by tightening the...
CC02 Instruction Manual - Page 7
...Makita wrench to stop.
For 45° bevel cuts, align the B position with your cutting line. CAUTION: Do not pull the switch trigger hard without pressing the lock-off lever 2. Shaft lock 2. Hex bolt 2. Make sure the diamond wheel is installed...work on the diamond wheel case.
Release the switch trigger to install or remove the diamond wheel. Inner flange 5. Then remove the...
CC02 Instruction Manual - Page 8
...If an inner flange is positioned just below the screw head of the tank holder) is removed by chance, install the inner flange so that its protrusion (bigger side) faces inside as shown in the figure. Hex wrench... the motor housing so that the notch of the band (part of the tool as illustrated. Open
8 ENGLISH Notch of the band (part of the tool
Attach the tank on the tank and fill...
CC02 Instruction Manual - Page 9
... tile applications.
Feed water to diminish, dress the cutting edge of the wheel using Makita replacement parts. They may break. 1 ► 1 . CAUTION: If the cutting action of the diamond wheel begins to the wheel by Makita Authorized or Factory Service Centers, always using an old discarded coarse grit bench grinder wheel or concrete block. NOTICE...
CC02 Instruction Manual - Page 10
... shows the trouble is thoroughly inspected and tested before leaving the factory. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation or exclusion may also have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. MAKITA LIMITED...
CC02 Parts Breakdown - Page 2
...1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 2 PC. 1 PC. Model CC02R1/CC02Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
183E38-1
001 C10 809N93-6
001 D10
002
266560-4
003
183E38-1
003 C10 809N93...SET CAUTION LABEL INC. 3 TAPPING SCREW 4X40 MOTOR HOUSING SET CAUTION LABEL INC. 1 TAPPING SCREW 4X18 CC02 NAME PLATE TAPPING SCREW 4X18 HANDLE SET...
CC02 Parts Breakdown - Page 3
...HEX. LOCK NUT M5-8 THUMB SCREW M5X10 SPRING WASHER 5 FLAT WASHER 5 DEPTH GUIDE PIN 4 STOP RING E-3 PIN 5 ANGULAR GUIDE STOP RING E-3 BASE ASS'Y INC. 53-58 PAN HEAD SCREW M4X20 CAP B.... 39-41,60 HEX. WRENCH 4 DIAMOND WHEEL 85MM RIM WET BATTERY COVER DC10WD BATTERY CHARGER COMPO-PARTS BATTERY BL1021B SET (197414-3)
1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 ...
Makita CC02R1 New Tool Flyers English - Page 1
... and weighs only 4.0 lbs. stone and masonry (724950-8D)
All specifications subject to stock on hand. All models and accessories subject to change without prior notice. makitatools.com
Makita U.S.A., 14930 Northam St., La Mirada, CA 90638
NTF0516 MA6308-16 battery charge level indicator n Part of the expanding 12V max CXT™ series, combining performance...
Makita CC02Z Reviews
We have not received any reviews for Makita yet.