Makita CX200RB Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita CX200RB manuals!
Problems with Makita CX200RB?
Ask a Question
Free Makita CX200RB manuals!
Problems with Makita CX200RB?
Ask a Question
Popular Makita CX200RB Manual Pages
XDT15 Instruction Manual - Page 3
... the power tool, accessories and tool bits etc. avoid contact. Keep handles dry, clean and free from rotating parts. Always be caught in this instruction manual may cause irritation or burns.
3
Service 1. Be sure no load speed
revolutions or reciprocation per minute
number of fire when used for battery cartridge
1.
WARNING: DO NOT let...
XDT15 Instruction Manual - Page 4
... and even a breakdown.
6. SAVE THESE INSTRUCTIONS. CAUTION: Only use a damaged battery.
10. Let a hot battery cartridge cool down before installing or removing of the tool, causing injury... battery.
Overcharging shortens the battery service life.
3. CAUTION: Do not install the battery cartridge forcibly. Do not use genuine Makita batteries.
Charge the battery cartridge...
XDT15 Instruction Manual - Page 5
... and returns to 25%
Charge the battery. Electric brake
This tool is equipped with "B" at a Makita service center.
5 ENGLISH Overdischarge protection
When the battery capacity is increased by increasing pressure on again. Switch trigger
CAUTION: Before installing the battery cartridge into the tool, always check to see that causes it to become overloaded...
XDT15 Instruction Manual - Page 9
...repairs, any other maintenance or adjustment should be reduced. 2. Fastening torque 3.
NOTE: If the impact force is affected by Makita Authorized or Factory Service Centers, always using Makita replacement parts.... corresponding to each bolt diameter
Hold the tool firmly and place the point of the driver bit may result.
NOTE: When fastening M8 or smaller screw, choose a proper impact...
XDT15 Instruction Manual - Page 10
... WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY.
This Warranty does not apply where: • repairs have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge.
Some states do not allow the exclusion or...
XFD11ZB Instruction Manual - Page 2
...expose power tools to a rotating part of the power tool may ...to your mains-operated (corded) power tool or battery-operated (cordless) power tool. Electrical Safety 1. Never use . Use personal ...tools that have the switch on . Personal Safety
1. ENGLISH (Original instructions)
SPECIFICATIONS
Model:
XFD11
Drilling capacities
Steel
13 mm (1/2")
Wood
36 mm (1-7/16")
Fastening capacities
...
XFD11ZB Instruction Manual - Page 3
..., liquid may cause burns or a fire.
4. Cordless driver drill safety warnings
1. Fasteners contacting a "live " and could result in a hazardous situation. Do not leave the tool running.
volts
direct current
no one type of parts and any other condition that cannot be controlled with the power tool or these instructions, taking into account the working conditions...
XFD11ZB Instruction Manual - Page 4
...off and the battery cartridge is removed before installing or removing of non-genuine Makita batteries, or batteries that it from the...Do not incinerate the battery cartridge even if it all instructions and cautionary markings on the upper side of overheating, possible burns... is completely worn out. Overcharging shortens the battery service life.
3. Charge the battery cartridge with clear ...
XFD11ZB Instruction Manual - Page 5
...Lighted
Off 75% to the "OFF" position when released.
Switch trigger
CAUTION: Before installing the battery cartridge into the tool, always check to see that the switch trigger actuates ... equipped with "B" at the end of the model number
Overdischarge protection
When the battery capacity is released, have the tool serviced at a Makita service center.
5 ENGLISH Release the switch trigger to...
XFD11ZB Instruction Manual - Page 7
...set at the number 1 to tighten the chuck.
lauan)
ɸ3.5 x 22
ɸ4.1x 38
- Place the driver bit/drill.... The following shows the rough guide of the tool. To remove the driver bit/drill bit, turn the sleeve counterclockwise....632;3.5 x 22
ɸ4.1x 38
- Installing or removing driver bit/ drill bit
Optional accessory
Turn the sleeve counterclockwise to determine which torque level is ...
XFD11ZB Instruction Manual - Page 8
... guide screw makes drilling easier by setting the reversing switch to back out.
Use a cutting lubricant when drilling metals.
There is inserted straight in wood, the best results are iron and brass which should be seen.
CAUTION: Always secure workpieces in a vise or similar hold it in order to reverse rotation in the driver bit...
XFD11ZB Instruction Manual - Page 9
... LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is caused by Makita Authorized or Factory Service Centers, always using Makita replacement parts. If inspection shows the trouble is thoroughly inspected and tested before attempting to the tool. To maintain product SAFETY and RELIABILITY, repairs, any trouble develop during this manual.
Using the tool as tightening bolt or...
XDT15 Parts Breakdown - Page 2
...1 PC. 1 PC. 1 PC. 1 PC. 1 2 PC. 0 1 3 PC. 1 1 1 PC. 1 PC. Model XDT15ZB Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
001
183E57-7
001 C10 252126-6
001 D10
002
852P14-9
003
266429-2
004
455053-8
005
143975-1
006
619415-6
007
629233-4
...620586-4
042
810H96-9
A01
266622-8
A02
346449-3
HOUSING SET HEX. LOCKING NUT M4-7 INC. 35 XDT15 NAME ...
XFD11 Parts Breakdown - Page 2
... HEAD SCREW M6X22 KEYLESS DRILL CHUCK 13 CHANGE LEVER ASS'Y INC. 5 GEAR ASSEMBLY TAPPING SCREW PT 2X6 CONTROLLER STATOR ROTOR TERMINAL HOUSING SET RUBBER PIN 6 HEX. LOCKING NUT M4-7 INC. 17 XFD11 NAME PLATE TAPPING SCREW 3X16 SPEED CHANGE LEVER COMPRESSION SPRING 2 F/R CHANGE LEVER SWITCH C3JW-2B - Model XFD11ZB Parts Price List
A = Standard Equipment 〇...
Makita CX200RB New Tool Flyers English - Page 1
...;m) Overall Length Net Weight (with the U.S. Steel (1/2"), Wood (1-7/16") 0 - 500 / 0 - 1,700 RPM 350 in .lbs. 18V LXT® Lithium-Ion Sub-Compact Brushless Cordless 2-Pc.
Combo Kit (2.0Ah)
Model CX200RB
SUB-COMPACT, BRUSHLESS AND ERGONOMIC DESIGN
DRIVER-DRILL
Compact and ergonomic design at only 6-3/8" long n Mechanical variable 2-speed transmission (0-500 & 0-1,700 RPM)
for...
Makita CX200RB Reviews
We have not received any reviews for Makita yet.