Makita GHU05Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita GHU05Z manuals!
Problems with Makita GHU05Z?
Ask a Question
Free Makita GHU05Z manuals!
Problems with Makita GHU05Z?
Ask a Question
Popular Makita GHU05Z Manual Pages
Instruction Manual - Page 2
ENGLISH (Original instructions)
SPECIFICATIONS
Model:
GHU04
GHU05
Blade length
600 mm (23-5/8")
750 mm (29-1/2")
Strokes per minute
2,...8226; Some of the battery cartridges and chargers listed above may differ from heat, oil, sharp edges or moving parts.
Cluttered or
dark areas invite accidents. 2. Power tools create sparks which may differ depending on the attachment(s), ...
Instruction Manual - Page 3
...parts, breakage of their device and/or doctor for advice before use. Check for which may be performed. Properly maintained cutting tools with these instructions...of injury and fire.
3. Recharge only with specifically designated battery packs. Use power tools only ..., keys, nails, screws or other battery packs may be repaired.
3
3. Liquid ejected from the battery; If operating a...
Instruction Manual - Page 4
...instruction for damage, and if damaged, replace the blades immediately.
7. Proper carrying of age. When clearing jammed material or servicing the unit, make sure all parts of the hedge trimmer while clearing jammed material or servicing...to be used by a qualified repair person using tools such as indicated....
12. Also wear sturdy shoes with local codes for the reason that the tool is a ...
Instruction Manual - Page 5
... comfort or familiarity with local codes for tool. If electrolyte gets into storage for battery cartridge
1. The battery cartridge can explode in the rain.
9. 3. Do not replace the battery with the blade ... remove the battery cartridge and put on how often you do this type of this instruction manual may explode. Your risk from repeated use , or store the battery in a fire, ...
Instruction Manual - Page 6
... resulting in burns or personal injury.
17. SAVE THESE INSTRUCTIONS. Tips for the Makita tool and charger. Charge the battery... tool supports the use near high-voltage electrical power lines, do not use as shown in a safe place. To install the ... battery cartridge.
18. Overcharging shortens the battery service life.
3. Red indicator 2. Always stop tool operation and charge the battery ...
Instruction Manual - Page 8
...of control and serious personal injury.
WARNING: Before installing the battery cartridge on again to restart. 2. ... lever and the switch trigger.
This can lead to our authorized service center for proper repairs BEFORE further usage. When you press the main power button, the...indicators go off function. Charge the battery(ies) or replace it runs when you turn on the tool. Return the...
Instruction Manual - Page 9
... Makita Authorized Service Center.
• Accidental re-start preventive function Even if you change the direction of load conditions.
• Electric brake This tool is removed before removing or installing the shear blades. When entangled branches and debris are removed, the tool returns to a different length, replace the chip receiver with an electric...
Instruction Manual - Page 13
... out, ask Makita Authorized Service Centers for parts replacement or repairs. CAUTION: Be careful not to allow the shear blades to the tool by tightening four screws (for GHU04) or five screws (for GHU05), and then remove the chip receiver from the tool. Removing or installing the chip receiver
CAUTION: When installing or removing the chip...
Instruction Manual - Page 15
...not exposed to the tool. Install the battery cartridge to the...blades are positioned alternately. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be sure that the tool... the tool
Clean the tool by Makita Authorized or Factory Service Centers, always using Makita replacement parts. NOTICE: Never use gasoline, benzine, thinner, alcohol or...
Instruction Manual - Page 16
....
5. Dressing stone
6. Tighten the bolt.
16 ENGLISH
Bolt
2.
Return the tool to 45°, and grind the lower blade from 3 directions with the dressing stone. Set the angle of lubrication: Every 50 operating hours 1. Hole
3. Align the outlet of the grease vessel onto the hole.
1
Fig.42 ►...
Instruction Manual - Page 17
... your local authorized service center for repair. If recharging is not installed. Tool does not reach maximum RPM.
Use the reverse button. 2.
Ask your local authorized service center for repair.
If you find a problem that is low.
MAKITA LIMITED WARRANTY
Please refer to the annexed warranty sheet for repair.
Battery cartridge is not effective, replace battery. If...
Parts Breakdown - Page 3
... R TORSION SPRING 9 SWITCH C3XA-1PSPM
SWITCH CIRCUIT COMPLETE E SWITCH LABEL GRIP SET HEX. 1 GHU05
Motor/Throttle Control
Products with multiple versions are listed in subsiding order with the newest version on top not indented. GHU05 Tech Bulletin
Part No.
1 1 183U16-7
1
252180-0
1 2 455629-1
1 3 233621-5
1 4 412315-7
1 5 233621-5
1 6 651083-9
1 7 141D66-6
1
8034K3-2
1 8 183U16...
Parts Breakdown - Page 4
Part No.
1 30 266326-2 1 73 620G85-8 1 74 140W63-3 1 76 183U18-3 1 77 183U18-3 1 78 266326-2 1 79 266420-0 1 80 638A24-8
Description
TAPPING SCREW 4X18 CONTROLLER INDICATION CIRCUIT COMPLETE FRONT GRIP SET FRONT GRIP SET TAPPING SCREW 4X18 TAPPING SCREW 5X20 LEAD UNIT
4
1
1
1
INC. 77
1
INC. 76
2
1
1
Notes
rev 1_22-05-16
4 Section Fig.
GHU05 Tech Bulletin...
Parts Breakdown - Page 6
No. GHU05 Tech Bulletin
2 GHU05
Cutting Device
Products with multiple versions are listed in subsiding order with the newest version on top not indented.
Part No. Description
2 31 266326-2
TAPPING SCREW 4X18
6
2 32 266326-2
TAPPING SCREW 4X18
2
2 33 413B91-8
FRONT GRIP RETAINER A
1
2 34 632T12-1
SWITCH UNIT
1
2 35 413B87-9
SWITCH LEVER F
1
2 ...
Parts Breakdown - Page 7
... 5 CHIP RECEIVER 750 SET BINDING HEAD SCREW M5X12 BLADE COVER 750 GEAR GREASE
Notes
1
6
3
3
1
3
INC WITH FIG 70/NOT PICTURED
1
5
1
NOT PICTURED
1
rev 1_22-05-16
7 Part No.
2 65 266559-9
2 66 922128-3
2 67 310983-9
2 69 265A89-3
2 70 191Y05-2
2
310983-9
2 71 191D34-9
2 72 265B57-2
2 A01 413B99-2
2 A08 197439-7
Description
H.S.BUTTON HEAD BOLT M6X4...
Makita GHU05Z Reviews
We have not received any reviews for Makita yet.