Makita GRU02M1 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita GRU02M1 manuals!
Problems with Makita GRU02M1?
Ask a Question
Free Makita GRU02M1 manuals!
Problems with Makita GRU02M1?
Ask a Question
Popular Makita GRU02M1 Manual Pages
Instruction Manual - Page 2
...specifications herein are shown in the table.
SAFETY WARNINGS
Important safety instructions
WARNING: When using the cord connected power source, read the instruction manual... instructions 1. SAVE THESE INSTRUCTIONS. ENGLISH (Original instructions)
SPECIFICATIONS
Model: Handle type No load speed (at each rotation speed level)
Overall length (without notice.
• Specifications may...
Instruction Manual - Page 4
...replacement parts. Check for operation. Do not expose a battery pack or machine to feet and hands from the tool or charger, be properly repaired or replaced by our authorized service center unless indicated elsewhere in the instructions...not handle charger, including charger plug, and charger terminals with local codes for easy and proper action. Before starting make sure that the ...
Instruction Manual - Page 6
...tool. MISUSE or failure to occur in this instruction manual may fall suddenly and cause an injury. ... filter out microscopic particles. Maintenance instructions
1. Have the tool repaired only by our authorized service center.
8. Do not wash ... and 2 o'clock.
4. Use only the manufacturer's recommended replacement parts and accessories.
7. Symbols
The followings show the symbols used...
Instruction Manual - Page 7
...e.g. Follow your eyesight.
5. Unless the tool supports the use near a high-voltage electrical power ...in a risk of electrolyte.
13. Installing the batteries to the handling of the...tool and charger. Overcharging shortens the battery service life.
3. If electrolyte gets into ...safety instructions for hazardous material is required. Before using battery cartridge, read all instructions ...
Instruction Manual - Page 10
...the battery protection system works.
► 1 .
CAUTION: Before installing the battery cartridge into the tool, always check to the "...to 100%
50% to 75%
25% to 50%
0% to our authorized service center for a few seconds. NOTE: Depending on the main power button and ...Indicator lamps 2. The indicator lamps light up for proper repairs BEFORE further usage.
Return the tool to 25%
Charge...
Instruction Manual - Page 12
...removal
WARNING: Switch off lever when the cutting tool is released, have the tool serviced at our service center. Soft start feature
Soft start the tool unless it is removed before you .... Insert the shaft of suppressed starting shock. Tighten the screw securely.
► 1 .
Installing the handle
For GRU02 1. Reverse
1
button
NOTE: During the reverse rotation, the tool operates...
Instruction Manual - Page 13
...the handle on the upper clamp and fix it with hex socket head bolts as a safety part to keep it from contacting the cutting blade accidentally. Hex socket head bolt 2. Upper clamp
4.... using the screw on the damper. 2. Lower clamp
Attaching the barrier
For the loop handle model only (country specific) If the barrier is included in the tool head. Adjust the handle position, and then ...
Instruction Manual - Page 15
... section for specifications.
3-tooth blade 4-tooth blade
15 ENGLISH If the cutter blade hits a stone during operation, stop the tool and check the cutter blade immediately. Clip
Installing the cutting ...tool
CAUTION: Always use the cutter blade with the diameter described in some countries.
NOTE: Turn the tool upside down so that you can replace the cutting...
Instruction Manual - Page 16
To remove the cutter blade, follow the installation procedures in the gear case to lock the spindle. Mount the... of the tool at all times.
Box wrench 2. Loosen 4.
Clamp washer 4. Loosen 5. To remove the nylon cutting head, follow the installation procedures in the same direction.
1
► 1 . Failure to the bystander and the operator.
2 ► 1 . 2. Nylon cutting...
Instruction Manual - Page 17
... the shoulder harness included in the tool package, but use the shoulder harness attached to the tool. For the recommended hanging band, ask Makita Authorized Service Centers. The shoulder harness features a means of the buckle while holding the tool to the hanger on the tool. Hook 3. Clasp the hook on the...
Instruction Manual - Page 19
...and RELIABILITY, repairs, any more.
To avoid overheating of the tool. Replacing the nylon ...replacing the nylon cord. Failure to do so may result in soapy water and wrung out.
Failure to the tool and result in this instruction manual. Cleaning the tool
Clean the tool by Makita Authorized or Factory Service...GRU02
GRU03
When using Makita replacement parts. The method of injury caused...
Instruction Manual - Page 21
... terms applicable to dismantle the tool. TROUBLESHOOTING
Before asking for repairs, conduct your local authorized service center for repair.
Cutting tool and motor cannot stop the machine immediately! Battery's charge level is not effective, replace battery cartridge. Recharge the battery cartridge. If recharging is installed improperly. Install the battery cartridge as a branch is...
Parts Breakdown - Page 3
... 609LLb
1
14 210049-4 BALL BEARING 609ZZ
1 15 257986-1
RETAINING RING (EXT) S-9
1 16 257987-9
RETAINING RING (INT)R-24
1 17 191B54-1
PROTECTOR U 430 SET MG
1 18 922216-6
HEX. GRU02 Tech Bulletin
Part No. SOCKET HEAD BOLT M5X25
1 20 327056-1
SHAFT
1 21 251513-6
H.S.H.BOLT M5X25
1 22 347107-4
PROTECTOR CLAMP 24
1 23 922216-6
HEX. SOCKET HEAD...
Parts Breakdown - Page 4
... listed in subsiding order with the newest version on top not indented. GRU02 Tech Bulletin
Part No. No.
LOCK NUT M5-8
1 41 266326-2
TAPPING SCREW 4X18
1 42 266326...
POWER SUPPLY CORD UNIT
1 46 183N25-4
HOUSING COVER SET
1 47 687051-6
STRAIN RELIEF
1 48 687124-5
STRAIN RELIEF
1 49 266326-2
TAPPING SCREW 4X18
1 50 183S87-2
HOUSING SET
1
263005-3
RUBBER PIN 6
1 51 911233-1
PAN...
Parts Breakdown - Page 5
GRU02 Tech Bulletin
Part No. No. Description
1 63 519647-4
ROTOR ASS'Y
1 64 211021-9
BALL BEARING 607LLB...SOCKET HEAD BOLT M5X12
1 72 266326-2
TAPPING SCREW 4X18
1 73 183N25-4
HOUSING COVER SET
1 74 922211-6
H.S.H.BOLT M5X12 WITH W
1 75 922233-6
H.S.H.BOLT M5X20 WITH WR
1 76 183S87-2
HOUSING SET
1
263005-3
RUBBER PIN 6
1 77 266326-2
TAPPING SCREW 4X18
1 78 266420-0
...
Makita GRU02M1 Reviews
We have not received any reviews for Makita yet.