Makita JS1600 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita JS1600 manuals!
Problems with Makita JS1600?
Ask a Question
Free Makita JS1600 manuals!
Problems with Makita JS1600?
Ask a Question
Makita JS1600 Videos
??????? Makita JS1600
Duration: 1:49
Total Views: 5,110
Duration: 1:49
Total Views: 5,110
AtelierulTau.ro - Masina de taiat tabla Makita JS1600
Duration: 2:42
Total Views: 3,921
Duration: 2:42
Total Views: 3,921
Makita js1600 Shears
Duration: :12
Total Views: 2
Duration: :12
Total Views: 2
JS1600
Duration: :14
Total Views: 740
Duration: :14
Total Views: 740
Popular Makita JS1600 Manual Pages
Owners Manual - Page 1
cutting capacitles
cutting
Mild steel
Stainless
radius
! Note: Specifications of parts and accessories without notice.
MODEL JS1600
INSTRUCTION MANUAL
DOUBLE INSULATION
Specifications
Max. I I
1.6"
1.2mm
( 1 / 1 6 ~ z ) (3,64,,1
;olzm)
1
I
I
Strokes m ipneurt e
4,000
Conratitninugous
Overall
Net
1 (Input) 300 W
I
length
weight
I 1 230" (9-118")
1 . 7 kg (3.7 Ibs)
I
...
Owners Manual - Page 2
...cords periodically and if damaged, have repaired by cord or yank it to disconnect...electric shock, and personal injury, including the following:
READ ALL INSTRUCTIONS.
1. Don't force small tool or attachment to determinethat it
was intended.
6.
They can be stored in
moving parts, breakage of the tool, a guard or other part that i s damaged should be kept away from tool before servicing...
Owners Manual - Page 3
...specified o n the nameplate o f the tool. G U A R D AGAINST ELECTRIC SHOCK. REPLACEMENT PARTS. VOLTAGE WARNING: Before connecting the t o o l t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is harmful t o the motor.
SAVE THESE INSTRUCTIONS. For example; pipes, radiators, ranges, refrigerator enclosures. 20. Shear & Standard Equipment
Tool body
I
I_
1
Switch...
Owners Manual - Page 4
...the switch lever (paddle switch) with the safety lock in the table on .
The maximum shearing thickness is shearable. Then squeeze the switch lever (paddle switch) to put it is indicated ....
(In FREE condition)
(In LOCK condition)
Switch lever (Paddle switch)
Fig. 1
Permissible Shearing Thickness .The groove on the tool; Attempting to work with the safety lock on the right ...
Owners Manual - Page 5
... poor
shearing action, and the service life of the tool will be used in a fresh set.
5 JIS SPC s55c
Shearing Method 0 Keep the shear moving parallel with the
material.
~
Fig. 4
Fig. 5 Blade Inspection .Before using the tool check the blades for cutting should be
fastened to the work bench by means of workholders. Replace worn blades as follows. +Blades may...
Owners Manual - Page 6
...socket hd. I
I
.Turn the shear blade and replace with the hex wrench provided. Keep pressure on the shear blade while tightening it. Blade holder Hex socket h d bolt
Shear blade
No clearance allowed
Fig.
Thin-washers
@& Blade holder
I
I
6 bolt with a new one or more washers between the shear blade and blade holder bevelled surf ace.
Changing Blade Position
.Use the hex wrench...
Owners Manual - Page 7
... in the diagram on the right is factory- hold -down screw
(flat tip)
/- assembled.
shearing width (A)
No limit
7 Stationary
/=-
Do not tamper with the hex wrench. I
(0.04")
Cuttino line
Max. When installing the stationary blade onto the yoke, the blade should be pressed against the yoke so as to be no clearance between A, B and...
Owners Manual - Page 8
L..
.
3mm (1/8")
Fig. 1:
* T o replace the carbon brushes, use a minus (-1 head screwdriver to about 3 mm (1/8") or sparking will occur. 0 Replace carbon brushes when they wear down to remove the brush
holder cap. e------
I
I
Fig. 13
Fig. 14
8 Both brushes should be changed at the same time.
Owners Manual - Page 9
... other accessory might be hazardous. Set the shear blade on the right), so that there is 0.1 0.2 mm
(4 mil - 8 mil)
1. screw. F i t as seen on the blade installing portion of the above washers and insert it between the blades.
4. The use with the hex.
Blades (two per set of brister package) Part No. 191384-8
0 Hex wrench Part No. 783201-2
PROPER BLADE CLEARANCE ADJUSTMENT
-
Owners Manual - Page 11
...Helical Gear 391 F. Bolt M4x55 IWith Warher) Rubber Pin 4 Pin 6 S Screw MBx16 Protector S Washer 5 H S H Bolt M5x10 Blade Holder T. Washer 6 Gear Housing Cover Ball Bearing 608LB Fan 58 ARMATURE ASSEMBLY IArrembled Items 11. 12.13. 14 & 151 Insulation Washer ... Items 45 47 & 491 Switch Lever P,n 4 Safety Lock
4CCESSORIES
1 1 100
1
iii
Wrench Holder 3-7 H Wrench 3 Shear Blade ti.
Owners Manual - Page 12
... Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi 446 Japan
883248A069
PRINTED IN JAPAN
1991 - 6 - Should any trouble ...repairs have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC...
Parts Breakdown - Page 2
...JS1600 SET SCREW M8X16, JS1600 PROTECTOR, JS1600 SPRING WASHER 5, 9005B H.S.H. BOLT M4X10, BO5001 H.S.H. WASHER 10, 9901 CRANKSHAFT, JS1600 F. WASHER 6, NHP1310 GEAR HOUSING COVER, JS1600 B. BOLT M5X10, 5090DW
H.S.H. BOLT M5X10, JS1600 BLADE HOLDER, JS1600 T. Parts Breakdown
JS1600..., DA3000 WRENCH HOLDER, JR3000V HEX WRENCH 3, AF501 SHEAR BLADE SET, JS1600 (T2) N/A
Quantity 4 1 1 1 1 ...
Makita JS1600 Reviews
We have not received any reviews for Makita yet.