Makita XAG01 Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita XAG01 manuals!
Problems with Makita XAG01?
Ask a Question
Free Makita XAG01 manuals!
Problems with Makita XAG01?
Ask a Question
Popular Makita XAG01 Manual Pages
Makita DC18RC Instruction Manual - Page 3
...
Specifications
Model Input Output Weight
DC18RA
DC18RC
A.C. 120 V 50 - 60 HZ
D.C. 7.2 V - 18 V
0.88 kg (1.94 lbs)
0.77 kg (1.70 lbs)
• Manufacturer reserves the right to change specifications ...battery charger, read all instructions and cautionary markings on the charger
label. Make sure cord is damaged, ask Makita authorized
service center to replace it to EPTA-Procedure...
Makita DC18RC Instruction Manual - Page 4
... heated battery in order although no trouble on the charger.
• Yellow... order to enable the battery to direct sunlight for charging Makita-battery cartridge. Recharge of cells
14.4 V 4
18 ...charging time will begin after the cooling fan installed in the following cases. - Check the ...of the optimal charging selected according to repair or maintenance, if the yellow warning light...
XAG01Z Instruction Manual - Page 2
....
2 Remove any adjusting key or wrench before connecting to a rotating part of the power tool may result in the presence of flammable liquids, gases...power tools in explosive
atmospheres, such as pipes, radiators, ranges and refrigerators. ENGLISH (Original instructions)
SPECIFICATIONS
Model
XAG01
Wheel diameter
115mm (4-1/2")
Spindle thread
5/8"
No load speed (RPM)
10,000 /min
...
XAG01Z Instruction Manual - Page 3
... or other battery packs may be sure to damage the spindle, the flange (especially the installing surface) or the lock nut. If you use proper guard with these parts could result in use ) replace strict adherence to these instructions, taking into account the working conditions and the work to control. 23. Keep your hair...
XAG01Z Instruction Manual - Page 4
.... Hold the tool firmly. 11. Watch for these types of this instruction manual may result in locations where the temperature may be extremely hot and could indicate poor installation or a poorly balanced wheel. 14. Use of wheels and the use it .
4. This grinder is not designed for vibration or wobbling that sparks fly away...
XAG01Z Instruction Manual - Page 5
... one of the battery cartridge. • Hold the tool and the battery cartridge firmly
when installing or removing battery cartridge.
If it may cause them to slip off your hands and result ...In this situation, move it is not locked completely. This prevents the motor and its related parts from the tool while sliding the button on the upper side of the cartridge.
Then turn...
XAG01Z Instruction Manual - Page 6
...
WARNING: • When using a depressed center grinding
wheel/Multi-disc, flex wheel, wire wheel brush, cutoff wheel or diamond wheel, the wheel guard must be sure that of the tool as shown...lock when the spindle is installed
securely before carrying out any work . − To start the tool, slide the slide switch toward the operator. − Battery cartridge replacing signal − When ...
XAG01Z Instruction Manual - Page 7
...the lock nut onto the spindle. Follow instructions for rotation provided on the tool. Mount ... guard when depressed
center grinding wheel/Multi-disc is pointing in this manual.
To tighten the lock nut, press the shaft lock firmly so ...nut 2. Plastic pad
3
4. Abrasive disc
3. Lock nut
2. Installing or removing abrasive disc (optional accessory)
1
1. Spindle
007219
WARNING...
XAG01Z Instruction Manual - Page 8
... If the tool is out of about 15 degrees to 5 mm. Adjust
pressure on a grinder frequently kick and cause loss of control leading to twisting or binding of the wheel has been ...8226; It should never be necessary to the workpiece. The
weight of damaged brush could cause dangerous wheel breakage. • ALWAYS replace wheel if tool is started in the workpiece. • A diamond wheel shall...
XAG01Z Instruction Manual - Page 9
... is damaged, or which causes over bending of wires, leading to make an excessive depth of balance. MAINTENANCE
CAUTION: • Always be sure to spindle. Replacing carbon brushes
1. Overstressing the wheel increases the loading and susceptibility to perform inspection or maintenance. • Never use wire wheel...
XAG01Z Instruction Manual - Page 10
...
Reinstall the holder cap cover on the tool. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be used with a depressed center grinding wheel, multi-disc, diamond wheel, flex wheel and wire wheel brush. A cut-off wheel can also be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
XAG01Z Instruction Manual - Page 11
... 45
4
4-1/2" Depressed center grinding wheel/4-1/2" Multi-disc
5
Lock nut 5/8-45
6
N/A
7
N/A
8
Rubber pad 100
9
Abrasive disc
10
Sanding lock nut 5/8-48
11
Wire wheel brush
12
Wire cup brush
13
Wheel guard (For cut-off wheel)
14
Cut-off wheel / 4-1/2"Diamond wheel
- Lock nut wrench 28
014077
NOTE:
• Some items in the...
XAG01Z Instruction Manual - Page 12
...specific legal rights, and you . This Warranty does not apply where:
repairs have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace...SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY. Some states do not allow the exclusion or limitation of Makita's Factory or Authorized Service...WARRANTY. Should any trouble develop during this ...
XAG01Z Parts Breakdown - Page 2
Model XAG01/XAG01Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
619218-8
001 ...LED CIRCUIT YOKE UNIT ENDBELL COMPLETE XAG01 NAME PLATE TAPPING SCREW 4X18 SWITCH KNOB HOUSING SET RUBBER PIN 6 INC. 42 SWITCH LEVER SWITCH 1246.3223 CONTROLLER TERMINAL HOUSING SET RUBBER PIN 6 INC. 37 CARBON BRUSH CB-430 (195018-5) BRUSH HOLDER CAP
1 PC. 1 PC...
XAG01Z Parts Breakdown - Page 3
... 265103-9
A07
724115-A
A08
450128-8
A09
741423-B-25
E01
803C96-6
HOLDER CAP COVER GRIP 36 COMPLETE LOCK NUT WRENCH 28 DC18RC FAST CHARGER BATTERY BL1830 SET PLASTIC CARRYING CASE LATCH WHEEL COVER ASS'Y PAN HEAD SCREW M5X14 THIN CUTTING 115 BATTERY COVER 4 1/2" GRINDING WHEEL 115X6X22 CAUTION LABEL
2 PC. 1 PC. 1 PC. 1 PC...
Makita XAG01 Reviews
Do you have an experience with the Makita XAG01 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!