Makita XAG04T Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XAG04T manuals!
Problems with Makita XAG04T?
Ask a Question
Free Makita XAG04T manuals!
Problems with Makita XAG04T?
Ask a Question
Popular Makita XAG04T Manual Pages
XAG03Z Instruction Manual - Page 1
INSTRUCTION MANUAL
Cordless Angle Grinder
XAG03 XAG04
IMPORTANT: Read Before Using. 1
015078
XAG03Z Instruction Manual - Page 2
... operating power tools may differ from heat, oil, sharp edges or moving parts. Do not expose power tools to follow the warnings and instructions may ignite the dust or fumes. 3. Failure to rain or wet conditions... equipment. Power tool plugs must match the outlet. ENGLISH (Original instructions)
SPECIFICATIONS
Model
XAG03
XAG04
Wheel diameter
115 mm (4-1/2")
125 mm (5")
Max.
XAG03Z Instruction Manual - Page 3
...parts, breakage of parts and any other battery packs may be performed with the power tool or these instructions...instructions, illustrations and specifications...parts...parts...instructions... Follow instruction for Grinding... a rotating part of any ...instructions...Service 28. Operations for your power tool serviced...specifically designated battery packs. If damaged, have the power tool repaired...
XAG03Z Instruction Manual - Page 4
... the accessory's rotation at maximum no-load speed for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from work area must... is dropped, inspect for one minute. The motor's fan will also make exposed metal parts of your clothing, pulling the accessory into the surface of the rotating accessory and run ...
XAG03Z Instruction Manual - Page 5
... or wobbling that could indicate poor installation or a poorly balanced wheel. 21...Specific for Sanding Operations: a) Do not use undamaged wheel flanges that are of operation, is not designed for a while. e) Support...parts could ignite clothing. Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may expand in the workpiece. Safety Warnings Specific...
XAG03Z Instruction Manual - Page 6
... is severely damaged or is properly supported. 29. Do not use a damaged... service life.
3. Operate the tool only when hand-held.
23. SAVE THESE INSTRUCTIONS....replace strict adherence
to disposal of the manufacturer for maintaining maximum battery life
1. Observe the instructions...6.
Do not leave the tool running. it for this
instruction manual may reach or exceed 50 ﾟ C (122 ...
XAG03Z Instruction Manual - Page 8
... protection system The tool is
moving. To release the protection lock, remove the battery, set it to extend tool and battery life. It automatically changes operation mode depending on the ...cartridge is overheated
015083
Screw the side grip securely on to prevent spindle rotation when installing or removing accessories. Overload protection When the tool is overheated, the tool stops ...
XAG03Z Instruction Manual - Page 9
...tighten the screw to fasten the wheel guard. To remove wheel guard, follow the installation procedure in reverse.
9 Screw
4. Bearing box 3.
Fit the wheel/disc on the...
2 center wheel
3. Then rotate the wheel guard around 180 ﾟ counterclockwise. Screw
2
2. Installing or removing wheel guard (For depressed center wheel, multi disc / abrasive cut-off wheel, diamond ...
XAG03Z Instruction Manual - Page 10
...accessories specified in reverse.
Forcing and excessive pressure could cause dangerous wheel breakage. • ALWAYS replace wheel if tool is in both A
and B direction. This can cause loss of control ...lock nut wrench and securely tighten clockwise. To remove the disc, follow the installation procedure in this manual. Once the edge of the tool applies adequate pressure. The
weight of ...
XAG03Z Instruction Manual - Page 12
Remove any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
12 Regularly clean the tool's air vents or whenever the vents start to spindle. To maintain product SAFETY and RELIABILITY, repairs, any accessories on spindle. Thread wire cup brush onto spindle and tighten with wire wheel...
XAG03Z Instruction Manual - Page 13
... optional guard for use with your local Makita Service Center. • Makita genuine battery and charger
13 OPTIONAL ACCESSORIES
CAUTION: • These accessories or attachments are also available and should only be sure to obtain and use all necessary fasteners and guards as recommended in this manual. The use with a guard for more details...
XAG03Z Instruction Manual - Page 14
They may be included in the tool package as standard accessories.
1
2
6
2
10
11
3
7
9
3
4
8
12
5 5
115 mm (4-1/2") model
125 mm (5") model
1
Grip 36
2
Wheel Guard (for grinding wheel)
3
Inner flange 45
Inner flange 45
4
Depressed center wheel/Multi-disc
5
Lock nut 5/8-45
Lock nut 5/8-45
6
Rubber ...
XAG03Z Instruction Manual - Page 15
If inspection shows the trouble is caused by others: repairs are required because of Makita's Factory or Authorized Service Centers. MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY. Some states do not allow limitation on how long an implied warranty...
Makita XAG04Z Parts Breakdown - Page 2
... COMPLETE SWITCH 1246.3223 MOTOR HOUSING SET RUBBER PIN 6 INC. 33 DUST COVER L
1 1 PC. 1 0 1 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 4 PC. 1 PC. 1 PC. 1 1 PC. 1 PC. 1 PC. 1 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 4 PC. 1 PC. 1 PC. 1 1 PC. 1 PC. 1 PC. 1 PC. 1 5 PC. 1 1 PC. 2 PC. 0 1 1 1 1 1 1 1 PC. 1 PC. 2 PC. 0 1 Model XAG04Z Parts List
A = Standard Equipment 〇= Circuit Diagram...
Makita XAG04T New Tool Flyer English - Page 1
...or call 1-800-4MAKITA. The Makita Teal Color is protected under common law and registered with battery) UPC Code (XAG04T) UPC Code (XAG04Z)
Also Available as a Bare Tool Model XAG04Z
4 1/2" - 5" 18V...4-Port Charger (DC18SF)
All specifications subject to stock on for operator convenience n Soft start suppresses start -ups and longer gear life
SPECIFICATIONS
Wheel Diameter Battery No Load ...
Makita XAG04T Reviews
We have not received any reviews for Makita yet.