Makita XCU03PT1 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XCU03PT1 manuals!
Problems with Makita XCU03PT1?
Ask a Question
Free Makita XCU03PT1 manuals!
Problems with Makita XCU03PT1?
Ask a Question
Popular Makita XCU03PT1 Manual Pages
XCU03 Instruction Manual - Page 2
...ENGLISH (Original instructions)
SPECIFICATIONS
Model: Overall length (without notice.
• Specifications and battery cartridge may result.
2 ENGLISH Otherwise personal injury may differ from country to country.
• Weight, with 91PX
Guide bar
Guide bar length
Cutting length
Saw chain type (refer to the table below)
Sprocket
Number of teeth
Pitch
Recommended guide bar length...
XCU03 Instruction Manual - Page 4
...guide bar may cause chain breakage and/or kickback.
• Follow the manufacturer's sharpening and maintenance instructions for purposes not intended. Service
1.
A moment of inattention while operating chain saws may make exposed metal parts... the chain saw handles, with the saw chain and be controlled by a qualified repair person using only identical replacement parts. Proper...
XCU03 Instruction Manual - Page 5
... THESE INSTRUCTIONS. CAUTION: Only use ) replace strict adherence to follow the safety rules stated in this instruction manual may result in particular that: • The chain brake is working order and that it .
4. Use of overheating, possible burns and even an explosion. 4. It will also void the Makita warranty for tool. Starting the chain saw chain and guide bar...
XCU03 Instruction Manual - Page 8
... automatically shut down the
lock-off function.
NOTE: This chain saw , press the main power switch until the main power...installing the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to our authorized service... for proper repairs BEFORE further usage.
To turn off the main power switch when not in use the tool if it runs when you...
XCU03 Instruction Manual - Page 9
... is provided. Lock-off lever is performed, the saw with both hands when switching it on. Consult our authorized service center.
1. The saw then release the switch trigger completely. Unlocked position 3. Run the chain saw chain starts immediately.
2. Adjusting screw 9 ENGLISH Release the switch trigger to stop immediately when this test, stop within one...
XCU03 Instruction Manual - Page 12
..., use a safe support (saw chain when the motor is operating.
Oil tank (translucent)
After refilling, hold or steady it has been completely emptied, add oil up to operator. Start it may harm trees.
Keep proper footing and balance at all parts of the filler neck.
NOTICE: When filling the chain oil for Makita chain saws or...
XCU03 Instruction Manual - Page 13
...
► 1 .
When limbing, support the chain saw and the front one to -...grain cuts may only be deflected in the vicinity; • Any person involved has an unhindered path of retreat through a range of approximately 45° either side of kickback. Burrowing and parallel-to-grain cuts
CAUTION: Burrowing and parallel-to guide...the saw chain running, saw...
XCU03 Instruction Manual - Page 15
... ENGLISH The best cutting results are obtained with new one side only)
Sharpen the saw chain has been resharpened several times, have it sharpened in the figure.
► 1 . Saw chain -
Use a special round file (optional accessory) for
saw chain.
- Then the length of 30° must be guided more easily if a file holder
(optional accessory) is...
XCU03 Instruction Manual - Page 16
... a new saw chain. Have the sprocket replaced in the oil discharge hole during operation. These dust or particles may impair the oil to flow built-up in the guide bar ...time when you sharpen or replace the saw dust. Remove the sprocket cover and saw chain from the tool. File holder
- Remove the small dust or particles using the chain gauge tool (optional accessory). When a poor chain...
XCU03 Instruction Manual - Page 17
... tool, run it
-
-
- Failure to lubricate the saw must be worn out
Always fit a new locking ring when replacing the sprocket.
► 1 . Annually -
Guide bar
Inspection.
-
-
-
-
The user of the safety features, the following maintenance must not perform maintenance work is installed as shown in the instruction manual. Check item / Operating time
Chain saw...
XCU03 Instruction Manual - Page 18
... cartridge is blinking.
be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts for repair.
18 ENGLISH
The main power lamp is installed improperly. Oil guide groove is empty. Turn on the main power switch again. Chain catcher Inspection.
-
- Every 3 month
-
-
-
- TROUBLESHOOTING
Before asking for repair.
Fill the oil tank. Ask...
XCU03 Instruction Manual - Page 19
..., Makita will repair (or at our option, replace) without charge.
Should any trouble develop during this manual.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. Some states do not allow limitation on the chain saw. It must fit and fully cover the guide bar...
Makita XCU03 Parts Breakdown - Page 6
... SCREW 4X18
2
2 52
347079-3
CHAIN CATCHER
1
2 53
266326-2
TAPPING SCREW 4X18
1
2 54
346694-0
GUIDE PLATE ES
1
2 55
266166-8
TAPPING SCREW CT 3X8
1
2 56
346699-0
GUIDE PLATE CS
1
2 57
227496-2
...142288-7
WHEEL COMPLETE
1
Notes
rev 2_08-11-17
6 Part No. No.
XCU03 Tech Bulletin
XCU03 2 SPIKE BUMPER, GUIDE PLATE, BEVEL GEAR
Products with multiple versions are listed in...
Makita XCU03 Parts Breakdown - Page 8
...
Part No.
165246-6 196741-5 165245-8 163150-3 165201-8 165247-4 442-040-661 531-291-646 196519-6 196207-5 196742-3 196208-3 952-010-630
Description
GUIDE BAR, 14" 3/8 .043 SAW CHAIN SET 14" 3/8 .043 GUIDE BAR 12" 3/8 .043 GUIDE BAR 12" 3/8 .050 GUIDE BAR 14" 3/8 .050 GUIDE BAR 16" 3/8 .043 GUIDE BAR 16" 3/8 .050 SAW CHAIN SET 12" 3/8 .043 SAW CHAIN SET 12" 3/8 .050 SAW CHAIN SET 14...
Makita XCU03PT1 New Tool Flyer English - Page 1
...1
2
3
All specifications subject to gas chain saw off when operation is protected under common law and registered with battery 11.5 lbs. on hand. Shipping Weight (XCU03Z 10.5 lbs. 18V X2 (36V) LXT® LITHIUM-ION BRUSHLESS CORDLESS 14" CHAIN SAW KIT WITH 4 BATTERIES (5.0AH)
NEW TOOL OVERVIEW
XCU03PT1
ALSO AVAILABLE AS A BARE TOOL: XCU03Z
PRODUCT HIGHLIGHTS
POWER
Makita-built Outer...
Makita XCU03PT1 Reviews
We have not received any reviews for Makita yet.